Home › Engine / Hybrid System › A25A-FKS (ENGINE CONTROL) › SFI SYSTEM (w/o Canister Pump Module) › from 2021.02
RM33A0E _51 Engine / Hybrid System _065341 A25A-FKS ENGINE CONTROL _0344647 SFI SYSTEM(w/o Canister Pump Module) C

A25A-FKS ENGINE CONTROL  SFI SYSTEM(w/o Canister Pump Module)  P223711  O2 Sensor Positive Current Control Bank 1 Sensor 1 Circuit Short to Ground  P223712  O2 Sensor Positive Current Control Bank 1 Sensor 1 Circuit Short to Battery  P223713  A/F (O2) Sensor Positive Current Control Bank 1 Sensor 1 Circuit Open  P223716  O2 Sensor Positive Current Control Bank 1 Sensor 1 Circuit Voltage Below Threshold  P223717  O2 Sensor Positive Current Control Bank 1 Sensor 1 Circuit Voltage Above Threshold  P22371B  A/F (O2) Sensor Positive Current Control Bank 1 Sensor 1 Circuit Resistance Above Threshold  P225111  O2 Sensor Negative Current Control Bank 1 Sensor 1 Circuit Short to Ground  P225112  O2 Sensor Negative Current Control Bank 1 Sensor 1 Circuit Short to Battery  


DESCRIPTION

Refer to DTC P003012.

Click hereEngine / Hybrid System>A25A-FKS (ENGINE CONTROL)>SFI SYSTEM (w/o Canister Pump Module)>P003012

HINT:

Although the DTC titles say O2 sensor, these DTCs relate to the air fuel ratio sensor (sensor 1).


DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P223711 O2 Sensor Positive Current Control Bank 1 Sensor 1 Circuit Short to Ground The A1A+ voltage is 1.26 V or less for 5 seconds or more (2 trip detection logic).
·

Short in air fuel ratio sensor (sensor 1) circuit

·

Air fuel ratio sensor (sensor 1)

·

ECM


Comes on DTC stored SAE Code: P2238
P223712 O2 Sensor Positive Current Control Bank 1 Sensor 1 Circuit Short to Battery The A1A+ voltage is higher than 4.47 V for 5 seconds or more (2 trip detection logic).
·

Open or short in air fuel ratio sensor (sensor 1) circuit

·

Air fuel ratio sensor (sensor 1)

·

ECM


Comes on DTC stored SAE Code: P2239
P223713 A/F (O2) Sensor Positive Current Control Bank 1 Sensor 1 Circuit Open An open or ground short in the circuit between terminals A1A+ and A1A- of the air fuel ratio sensor (sensor 1) while the engine is running (2 trip detection logic).
·

Open or short in air fuel ratio sensor (sensor 1) circuit

·

Air fuel ratio sensor (sensor 1)

·

ECM


Comes on DTC stored SAE Code: P2237
P223716 O2 Sensor Positive Current Control Bank 1 Sensor 1 Circuit Voltage Below Threshold Difference between terminals A1A+ and A1A- is 0.2 V or less for 5 seconds or more (2 trip detection logic).
·

Open or short in air fuel ratio sensor (sensor 1) circuit

·

Air fuel ratio sensor (sensor 1)

·

ECM


Comes on DTC stored SAE Code: P2238
P223717 O2 Sensor Positive Current Control Bank 1 Sensor 1 Circuit Voltage Above Threshold Difference between terminals A1A+ and A1A- is higher than 1.04 V for 5 seconds or more (2 trip detection logic).
·

Open or short in air fuel ratio sensor (sensor 1) circuit

·

Air fuel ratio sensor (sensor 1)

·

ECM


Comes on DTC stored SAE Code: P2239
P22371B A/F (O2) Sensor Positive Current Control Bank 1 Sensor 1 Circuit Resistance Above Threshold The air fuel ratiosensor (sensor 1) impedance is higher than 185 Ω (2 trip detection logic).
·

Open or short in air fuel ratio sensor (sensor 1) circuit

·

Air fuel ratio sensor (sensor 1)

·

ECM


Comes on DTC stored SAE Code: P2238
P225111 O2 Sensor Negative Current Control Bank 1 Sensor 1 Circuit Short to Ground The A1A- voltage is 1.07 V or less for 5 seconds or more (2 trip detection logic).
·

Short in air fuel ratio sensor (sensor 1) circuit

·

Air fuel ratio sensor (sensor 1)

·

ECM


Comes on DTC stored SAE Code: P2252
P225112 O2 Sensor Negative Current Control Bank 1 Sensor 1 Circuit Short to Battery The A1A- voltage is higher than 3.93 V for 5 seconds or more (2 trip detection logic).
·

Open or short in air fuel ratio sensor (sensor 1) circuit

·

Air fuel ratio sensor (sensor 1)

·

ECM


Comes on DTC stored SAE Code: P2253

MONITOR DESCRIPTION

These DTCs are stored when there is an open or short in the air fuel ratio sensor (sensor 1) circuit, or the air fuel ratio sensor (sensor 1) output value is abnormal. The voltage of the air fuel ratio sensor (sensor 1) is monitored while the ignition switch ON, and the impedance (impedance is an electrical term that indicates the difficulty of flow of current) is checked while engine running. If the voltage of the air fuel ratio sensor (sensor 1) is outside the normal range, or the impedance is outside the normal range, the ECM illuminates the MIL and stores a DTC.

MONITOR STRATEGY

Required Sensors/Components Air fuel ratio sensor (sensor 1)
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Start the engine and wait 5 minutes or more [A].

7.

Turn the GTS on.

8.

Enter the following menus: Powertrain / Engine / Trouble Codes [B].

9.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



10.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

11.

Input the DTC: P223711, P223712, P223713, P223716, P223717, P22371B, P225111 or P225112.

12.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions



HINT:
·

If the judgment result is NORMAL, the system is normal.

·

If the judgment result is ABNORMAL, the system has a malfunction.

·

If the judgment result is INCOMPLETE, idle the engine for 5 minutes and check the DTC judgment result again.




CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:
·

Sensor 1 refers to the sensor closest to the engine assembly.

·

Sensor 2 refers to the sensor farthest away from the engine assembly.

·

Refer to "Data List / Active Test" [A/F (O2) Sensor Current B1S1].

Click hereEngine / Hybrid System>A25A-FKS (ENGINE CONTROL)>SFI SYSTEM (w/o Canister Pump Module)>DATA LIST / ACTIVE TEST

·

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK TERMINAL VOLTAGE (AIR FUEL RATIO SENSOR (SENSOR 1) VOLTAGE)
A402437C10
0.552,0.948 0.979,1.198 0.427,0.25 1.917,1.24 2.302,1.875 true 1.552,1.25 1.156,1.875 true 0.635,0.99 1.094,1.188 0.458,0.198 10 false C50 2.188,1.906 2.646,2.104 0.458,0.198 10 false A1A- 0.552,0.156 1.01,0.354 0.458,0.198 10 false *a 0.99,1.906 1.448,2.104 0.458,0.198 10 false A1A+
*a Front view of wire harness connector
(to Air Fuel Ratio Sensor (Sensor 1))


HINT:

Make sure that the connector is properly connected. If it is not, securely connect it and check for DTCs again.


a.

Disconnect the air fuel ratio sensor (sensor 1) connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C50-3 (A1A+) - Body ground Ignition switch ON 2.8 to 3.0 V
C50-4 (A1A-) - Body ground Ignition switch ON 2.3 to 2.7 V
C50-3 (A1A+) - C50-4 (A1A-) Ignition switch ON 0.1 to 0.7 V



HINT:

Perform "Inspection After Repair" after replacing the air fuel ratio sensor (sensor 1).

Click hereEngine / Hybrid System>A25A-FKS (ENGINE CONTROL)>SFI SYSTEM (w/o Canister Pump Module)>INITIALIZATION


Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR (SENSOR 1) - ECM)
2.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR (SENSOR 1) - ECM)
a.

Disconnect the air fuel ratio sensor (sensor 1) connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C50-1 (HA1A) - C57-9 (HA1A) Always Below 1 Ω
C50-3 (A1A+) - C57-95 (A1A+) Always Below 1 Ω
C50-4 (A1A-) - C57-94 (A1A-) Always Below 1 Ω
C50-1 (HA1A) or C57-9 (HA1A) - Body ground and other terminals Always 10 kΩ or higher
C50-3 (A1A+) or C57-95 (A1A+) - Body ground and other terminals Always 10 kΩ or higher
C50-4 (A1A-) or C57-94 (A1A-) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR