Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › from 2022.01
RM33A0E _57 Power Source / Network _065377 NETWORKING _0321446 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Tire Pressure Monitor ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Tire Pressure Monitor ECU Communication Stop Mode Any of the following conditions are met:
·

Communication stop for "Tire Pressure" is indicated on the "Communication Bus Check" screen of the GTS.

Click here(Click here)

·

Communication stop history for "Tire Pressure" is indicated on the "Communication Bus Check (Detail)" screen of the GTS. (The Lost Communication Time value for "Tire Pressure" is 6 or more.)

Click here(Click here)

·

Communication system DTCs (DTCs that start with U) that correspond to "Tire Pressure Monitor ECU Communication Stop Mode" in "DTC Combination Table" are output.

Click here(Click here)


·

Tire pressure warning ECU and receiver branch line or connector

·

Power source circuit of tire pressure warning ECU and receiver

·

Tire pressure warning ECU and receiver ground circuit

·

Tire pressure warning ECU and receiver



WIRING DIAGRAM

C382003E26
1.729,1.438 2.042,1.635 0.313,0.198 10 false 19 1.771,0.854 2.083,1.052 0.313,0.198 10 false 8 0.281,1.969 0.708,2.24 0.427,0.271 10 false R99 0.625,1.969 2.719,2.281 2.094,0.313 10 false No. 3 Junction Connector 2.26,3.271 3.396,3.594 1.135,0.323 10 false from Battery 1.708,2.448 3.302,2.844 1.594,0.396 10 false from IG1-NO. 1 Relay 3.885,2.281 5.094,2.625 1.208,0.344 10 false ECU-IG1 NO. 4 3.917,3.115 5.063,3.427 1.146,0.313 10 false ECU-B NO. 2 5.385,0.854 5.698,1.052 0.313,0.198 10 false 9 5.333,1.438 5.646,1.635 0.313,0.198 10 false 10 5.396,2.333 5.708,2.531 0.313,0.198 10 false 1 5.385,3.156 5.698,3.354 0.313,0.198 10 false 7 5.344,3.979 5.656,4.177 0.313,0.198 10 false 12 5.677,4.125 6.052,4.385 0.375,0.26 10 false GND 5.688,3.281 6,3.479 0.313,0.198 10 false +B 5.688,2.479 6.146,2.802 0.458,0.323 10 false IG 5.677,1.573 6.167,1.844 0.49,0.271 10 false CANL 5.677,0.99 6.208,1.323 0.531,0.333 10 false CANH 5.219,4.823 5.719,5.094 0.5,0.271 10 false R127 5.594,4.823 7.031,5.281 1.438,0.458 10 false Tire Pressure Warning ECU and Receiver

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (TIRE PRESSURE WARNING ECU AND RECEIVER BRANCH LINE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the R127 tire pressure warning ECU and receiver connector.


c.
C482146C07
1.469,0.313 1.896,0.583 0.427,0.271 1.604,2.24 1.604,2.99 1.604,2.99 1.438,2.99 true 1.802,2.24 1.802,2.99 1.802,2.99 1.969,2.99 true 0.125,0.083 0.438,0.281 0.313,0.198 10 false *a 1.521,0.375 1.979,0.563 0.458,0.188 10 false R127 1.01,2.906 1.625,3.188 0.615,0.281 10 false CANH 2.031,2.906 2.542,3.146 0.51,0.24 10 false CANL
*a Front view of wire harness connector
(to Tire Pressure Warning ECU and Receiver)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R127-9 (CANH) - R127-10 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Result
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (TIRE PRESSURE WARNING ECU AND RECEIVER)

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
C482146C08
1.49,0.406 1.917,0.677 0.427,0.271 1.198,2.25 1.198,2.833 1.198,2.833 1.031,2.833 true 2.219,2.24 2.219,2.823 2.219,2.823 2.385,2.823 true 1.188,1.792 1.188,0.875 1.188,0.875 1.021,0.875 true 0.125,0.083 0.438,0.281 0.313,0.198 10 false *a 1.542,0.458 2.01,0.656 0.469,0.198 10 false R127 0.781,2.75 1.094,2.948 0.313,0.198 10 false +B 0.844,0.792 1.458,1.073 0.615,0.281 10 false IG 2.458,2.75 2.865,3 0.406,0.25 10 false GND
*a Front view of wire harness connector
(to Tire Pressure Warning ECU and Receiver)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R127-12 (GND) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



b.

Reconnect the cable to the negative (-) battery terminal.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
R127-7 (+B) - Body ground Always 11 to 14 V
R127-1 (IG) - Body ground Ignition switch ON 11 to 14 V



Result:
Result
OK
NG



OK

REPLACE TIRE PRESSURE WARNING ECU AND RECEIVER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)