Home › Vehicle Exterior › BODY PANEL › FRONT BODY PILLAR(for Type B)
BM33C0E _01 Vehicle Exterior _068296 BODY PANEL _0332845 FRONT BODY PILLAR(for Type B) F

BODY PANEL  FRONT BODY PILLAR(for Type B)  CUT AND JOIN REPLACEMENT SECTIONS (PATTERN 1)  


K140654

With the cowl top side upper panel assembly removed.


REMOVAL


Symbol Meaning
K108818

Remove Weld Points
K108827

Cut and Join Location
K108828

Cut Location for Supply Parts

a.

Remove the front body pillar upper outer.

K143830C01
2.583,1.646 1.906,0.75 1.906,0.75 1.521,0.75 false 1.354,0.656 1.667,0.813 0.313,0.156 10 false *1
*1 FRONT BODY PILLAR UPPER OUTER - -
K111603

Laser Screw Welding - -


K140276C01
1.208,2.292 1.521,2.448 0.313,0.156 10 false *a
*a 290 mm (11.42 in.) - -


K140277


b.

Roughly cut open the panel so that the adhesive can be reached. Cut through the adhesive with a cut chisel to remove the panel.

HINT:

In cases where the adhesive cannot be removed with a cut chisel, heat the adhesive with an industrial heater gun or gas burner taking care not to cause panel deformation by overheating.


K143257C01
0,0 0,0 false
K108837

Adhesive - -



c.

Remove the front body pillar reinforce sub-assembly lower.

K143831C01
1.135,5.104 1.458,5.104 1.458,5.104 1.927,4.573 false 0.969,5.021 1.281,5.177 0.313,0.156 10 false *1
*1 FRONT BODY PILLAR REINFORCE SUB-ASSEMBLY LOWER - -
K111603

Laser Screw Welding - -


K140280


d.

When replace only the outer panel, please cut off a necessary range depending on a damage range.

i.

Carefully cut the outer panel so not to damage the reinforcement.


ii.

Make sure that butt welding does not heat-affect the reinforcement when welding the outer panel.




INSTALLATION


Symbol Meaning
K108821

Spot Weld
K108823

Plug Weld
K108831

Butt Weld
K108834

Body Sealer

a.

Inspect the fitting of the related parts around the new parts before welding. This affects the appearance of the finish.


b.

Temporarily install the new parts and measure each part of the new parts in accordance with the body dimension diagram. (See the body dimensions)


c.

Apply adhesive (3MTM AutomixTM Panel Bonding Adhesive #8115).

HINT:
·

Apply a light coat of adhesive around the plug welding points.

·

Apply enough adhesive to the panels.



K143257C01
0,0 0,0 false
K108837

Adhesive - -



d.

Weld the front body pillar reinforce sub-assembly lower to the vehicle side.

K143832C01
2.594,2.698 3.083,2.313 3.083,2.313 3.354,2.313 false 3.396,2.219 3.708,2.375 0.313,0.156 10 false *1
*1 FRONT BODY PILLAR REINFORCE SUB-ASSEMBLY LOWER - -
K111603

Laser Screw Welding - -


K140282


e.

Before installing a new part, apply body sealer.

HINT:

Apply body sealer in an even, continuous bead.


K140283


f.

Weld the front body pillar upper outer to the vehicle side.

K143833C01
5.615,4.396 6.031,3.979 false 2.573,2.938 3.01,2.74 3.01,2.74 3.323,2.74 false 3.354,2.656 3.667,2.813 0.313,0.156 10 false *1
*1 FRONT BODY PILLAR UPPER OUTER - -
K111603

Laser Screw Welding - -


K140285


g.

After welding, apply the foamed sealing material to the corresponding parts. (See the painting/coating)


h.

After welding, apply body sealer to the corresponding parts. (See the painting/coating)


i.

After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.