Home › Vehicle Exterior › BODY PANEL › ROCKER PANEL(for Type B) › 2017.09–2018.04
BM33C0E _01 Vehicle Exterior _068296 BODY PANEL _0332847 ROCKER PANEL(for Type B) F

BODY PANEL  ROCKER PANEL(for Type B)  CUT AND JOIN REPLACEMENT SECTIONS  


K140660

With the front body pillar cut and join replacement sections (pattern 1) removed.


REMOVAL


Symbol Meaning
K108818

Remove Weld Points
K108820

Remove Weld Points
K108826

Cut with Disc Sander etc.
K108827

Cut and Join Location
K108828

Cut Location for Supply Parts

a.

Do not butt weld or heat repair because the heat decreases the strength of areas where ultra high strength steel is used. (See the introduction)


b.

Carefully cut the No. 3 inner pillar sub-assembly so not to damage A.

K143834C01
3.531,7.292 3.333,7.292 3.333,7.292 3.24,6.99 false 3.396,5.917 3.083,5.625 3.083,5.625 2.885,5.625 false 3.552,7.208 3.865,7.365 0.313,0.156 10 false *1 4.938,3.344 5.25,3.5 0.313,0.156 10 false *a 4.302,6.167 4.615,6.323 0.313,0.156 10 false *b 2.75,5.552 3.063,5.708 0.313,0.156 10 false A
*1 NO. 3 INNER PILLAR SUB-ASSEMBLY - -
*a 95 mm (3.74 in.) *b 120 mm (4.72 in.)


K140330

K140331

K140332C01
3.667,0.333 3.979,0.49 0.313,0.156 10 false *A 3.688,2.583 4,2.74 0.313,0.156 10 false *B
*A PATTERN 1 *B PATTERN 2
K111603

Laser Screw Welding - -


K140333C01
0.271,0.344 0.583,0.5 0.313,0.156 10 false *A 3.688,0.344 4,0.5 0.313,0.156 10 false *B
*A PATTERN 1 *B PATTERN 2
K111603

Laser Screw Welding - -




INSTALLATION


Symbol Meaning
K108821

Spot Weld
K108823

Plug Weld
K108825

Plug Weld
K108827

Cut and Join Location
K108830

Fillet Weld
K108831

Butt Weld

a.

Inspect the fitting of the related parts around the new parts before welding. This affects the appearance of the finish.


b.

Temporarily install the new parts and measure each part of the new parts in accordance with the body dimension diagram. (See the body dimensions)


c.

If the entire supply part is not needed, remove the part of the supply part that is needed.

K140334C01
3.563,4.365 3.75,4.646 3.75,4.646 4.01,4.646 false 4.063,4.573 4.375,4.729 0.313,0.156 10 false *1 4.708,3.563 5.021,3.719 0.313,0.156 10 false *a
*1 NO. 3 INNER PILLAR SUB-ASSEMBLY - -
*a 120 mm (4.72 in.) - -



d.

Before temporarily installing the new parts, weld the center body pillar reinforce sub-assembly lower and No. 3 inner pillar sub-assembly with the standard number of welding points.

K143835C01
4.521,1.688 4.75,1.26 4.75,1.26 4.948,1.26 false 2.427,2.635 2.604,2.635 2.604,2.635 2.885,2.313 false 2.271,2.552 2.583,2.708 0.313,0.156 10 false *1 5,1.188 5.313,1.344 0.313,0.156 10 false *2
*1 CENTER BODY PILLAR REINFORCE SUB-ASSEMBLY LOWER *2 NO. 3 INNER PILLAR SUB-ASSEMBLY



e.

Weld the center body pillar reinforce sub-assembly lower and NO. 3 inner pillar sub-assembly to the vehicle side.

K143836C01
3.531,3.479 3.073,2.313 3.073,2.313 2.833,2.313 false 2.25,4.052 2.073,4.333 2.073,4.333 1.833,4.333 false 1.677,4.25 1.99,4.406 0.313,0.156 10 false *1 2.667,2.229 2.979,2.385 0.313,0.156 10 false *2
*1 CENTER BODY PILLAR REINFORCE SUB-ASSEMBLY LOWER *2 NO. 3 INNER PILLAR SUB-ASSEMBLY
*a Ultra High Strength Steel Welding Point *b Ultra High Strength Steel Welding Point


Follow the welding conditions below when welding ultra high strength steel to assure sufficient weld strength. (When repairing this model)

When welding 2 panels together including 980 MPa ultra high strength steel.

*a: Spot weld Pressure 2940 N (300 kgf, 661 lbf)
Weld current 10000 A
Weld time 18 Cyc.(0.27 Sec.)
*b: Plug weld Plug diameter 10 mm (0.39 in.)
Wire type AWS A5.18 ER70S-3
Shield gas Metal active gas

NOTICE:

Be sure to use Metal active gas (Ar 80% + CO2 20%) as the shield gas when plug welding.Sufficient weld strength cannot be assured when using 100% CO2 shield gas.



K140337C01
3.688,0.26 4,0.417 0.313,0.156 10 false *A 3.667,2.51 3.979,2.667 0.313,0.156 10 false *B
*A PATTERN 1 *B PATTERN 2
*a Ultra High Strength Steel Welding Point - -
K111603

Laser Screw Welding - -


Follow the welding conditions below when welding ultra high strength steel to assure sufficient weld strength. (When repairing this model)

When welding 2 panels together including 980 MPa ultra high strength steel.

*a: Plug weld Plug diameter 10 mm (0.39 in.)
Wire type AWS A5.18 ER70S-3
Shield gas Metal active gas

NOTICE:

Be sure to use Metal active gas (Ar 80% + CO2 20%) as the shield gas when plug welding.Sufficient weld strength cannot be assured when using 100% CO2 shield gas.



K140338C01
0.271,0.344 0.583,0.5 0.313,0.156 10 false *A 3.688,0.333 4,0.49 0.313,0.156 10 false *B 2.031,1.781 2.344,1.938 0.313,0.156 10 false *b
*A PATTERN 1 *B PATTERN 2
*a Ultra High Strength Steel Welding Point *b 15 mm (0.59 in.)
K111603

Laser Screw Welding - -


Follow the welding conditions below when welding ultra high strength steel to assure sufficient weld strength. (When repairing this model)

When welding 2 panels together including 980 MPa ultra high strength steel.

*a: Plug weld Plug diameter 10 mm (0.39 in.)
Wire type AWS A5.18 ER70S-3
Shield gas Metal active gas

NOTICE:

Be sure to use Metal active gas (Ar 80% + CO2 20%) as the shield gas when plug welding.Sufficient weld strength cannot be assured when using 100% CO2 shield gas.




f.

Weld the rocker panel outer to the vehicle side.

K143837C01
2.135,3.563 1.875,3.146 1.875,3.146 1.615,3.146 false 1.448,3.063 1.76,3.219 0.313,0.156 10 false *1
*1 ROCKER PANEL OUTER - -
*a Ultra High Strength Steel Welding Point - -


Follow the welding conditions below when welding ultra high strength steel to assure sufficient weld strength. (When repairing this model)

When welding more than 3 panels together including 980 MPa ultra high strength steel. (When plug welding a third panel to 2 panels which are welded under the conditions described above.)

*a: Plug weld Plug diameter Same as the standard method (See the introduction)
Wire type AWS A5.18 ER70S-3
Shield gas Metal active gas

NOTICE:

Be sure to use Metal active gas (Ar 80% + CO2 20%) as the shield gas when plug welding.Sufficient weld strength cannot be assured when using 100% CO2 shield gas.



K140340


g.

After welding, apply the foamed sealing material to the corresponding parts. (See the painting/coating)


h.

After welding, apply body sealer to the corresponding parts. (See the painting/coating)


i.

After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.