Home › Vehicle Exterior › BODY PANEL › ROOF PANEL(for Moon Roof)
BM33C0E _01 Vehicle Exterior _068296 BODY PANEL _0333357 ROOF PANEL(for Moon Roof) F

BODY PANEL  ROOF PANEL(for Moon Roof)  ASSEMBLY REPLACEMENT  


K140673

REMOVAL


Symbol Meaning
K108818

Remove Weld Points

a.

If reusing the roof panel reinforcement, trim the hemming location using a disc sander, etc.


b.

Roughly cut open the panel so that the adhesive can be reached. Cut through the adhesive with a cut chisel to remove the panel.

HINT:

In cases where the adhesive cannot be removed with a cut chisel, heat the adhesive with an industrial heater gun or gas burner taking care not to cause panel deformation by overheating.


K140234C01
0,0 0,0 false
K108837

Adhesive - -


K141440C01
1.656,5.365 1.771,5.365 1.771,5.365 1.958,5.135 false 1.49,5.26 1.802,5.417 0.313,0.156 10 false *a
*a Disc Sander - -
K111603

Laser Screw Welding - -


K140237



INSTALLATION


Symbol Meaning
K108823

Plug Weld
K108834

Body Sealer

a.

Inspect the fitting of the related parts around the new parts before welding. This affects the appearance of the finish.


b.

Temporarily install the new parts and measure each part of the new parts in accordance with the body dimension diagram. (See the body dimensions)


c.

Before temporarily installing the new parts, apply body sealer and adhesive (3MTM AutomixTM Panel Bonding Adhesive #8115) to the roof panel reinforcement.

HINT:

Apply enough body sealer and adhesive to the panels.


K140239C01
5.083,0.833 5.469,0.406 5.469,0.406 5.583,0.406 false 4.635,0.802 4.875,0.354 4.875,0.354 5,0.354 false 4.094,0.781 4.198,0.188 4.198,0.188 4.365,0.188 false 3.698,0.771 3.792,0.229 3.792,0.229 3.885,0.229 false 2.51,0.896 2.76,0.344 2.76,0.344 2.938,0.344 false 2.958,0.229 3.271,0.385 0.313,0.156 10 false *1 3.927,0.115 4.24,0.271 0.313,0.156 10 false *1 4.385,0.083 4.698,0.24 0.313,0.156 10 false *1 5.021,0.24 5.333,0.396 0.313,0.156 10 false *1 5.615,0.313 5.927,0.469 0.313,0.156 10 false *1
*1 ROOF PANEL REINFORCEMENT - -
K108837

Adhesive - -



d.

Before temporarily installing the new parts, weld the roof panel and roof panel reinforcement with the standard number of welding points.


e.

Bend the flange hem with a wooden hammer and dolly.

HINT:

Bend the panel gradually so as not to distort it.


K140240C01
1.052,5.083 1.208,5.083 1.208,5.083 1.469,4.833 false 1.292,3.417 1.438,3.417 1.438,3.417 1.75,3.969 false 2.104,4.021 2.354,3.594 2.354,3.594 2.51,3.594 false 2.615,0.729 2.75,0.323 2.75,0.323 2.875,0.323 false 3.865,0.771 3.927,0.458 3.927,0.458 4.021,0.458 false 4.26,0.74 4.354,0.448 4.354,0.448 4.448,0.448 false 4.771,0.781 4.938,0.417 4.938,0.417 5.042,0.417 false 5.208,0.74 5.792,0.229 5.792,0.229 5.938,0.229 false 5.771,0.854 6.125,0.656 6.125,0.656 6.271,0.656 false 6.313,0.552 6.625,0.708 0.313,0.156 10 false *1 4.052,0.354 4.365,0.51 0.313,0.156 10 false *2 0.896,4.979 1.208,5.135 0.313,0.156 10 false *a 1.115,3.313 1.427,3.469 0.313,0.156 10 false *b 2.542,3.479 2.854,3.635 0.313,0.156 10 false *c 2.906,0.219 3.219,0.375 0.313,0.156 10 false *2 4.469,0.344 4.781,0.5 0.313,0.156 10 false *2 5.073,0.323 5.385,0.479 0.313,0.156 10 false *2 5.99,0.125 6.302,0.281 0.313,0.156 10 false *2
*1 ROOF PANEL *2 ROOF PANEL REINFORCEMENT
*a Wooden Hammer *b Dolly
*c Cloth Tape - -



f.

Before temporarily installing the new parts, apply body sealer to the windshield header panel.

HINT:

Apply enough body sealer to the panels.


K141442C01
5.563,0.844 5.938,0.198 5.938,0.198 6.094,0.198 false 3.427,0.792 3.927,0.26 3.927,0.26 4.052,0.26 false 1.656,0.938 1.875,0.24 1.875,0.24 1.99,0.24 false 2.01,0.125 2.323,0.281 0.313,0.156 10 false *1 4.083,0.156 4.396,0.313 0.313,0.156 10 false *2 6.125,0.104 6.438,0.26 0.313,0.156 10 false *3
*1 WINDSHIELD HEADER PANEL *2 ROOF PANEL REINFORCEMENT
*3 BACK WINDOW FRAME - -


K141441C01
0,0 0,0 false
K111603

Laser Screw Welding - -


K140238


g.

After welding, apply the foamed sealing material to the corresponding parts. (See the painting/coating)


h.

After welding, apply body sealer to the corresponding parts. (See the painting/coating)


i.

After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.