Home › Vehicle Exterior › BODY PANEL › CENTER BODY PILLAR(for Type B) › from 2018.04
BM33C0E _01 Vehicle Exterior _068296 BODY PANEL _0332846 CENTER BODY PILLAR(for Type B) F

BODY PANEL  CENTER BODY PILLAR(for Type B)  CUT AND JOIN REPLACEMENT SECTIONS  


K140656

REMOVAL


Symbol Meaning
K108818

Remove Weld Points
K108820

Remove Weld Points
K108826

Cut with Disc Sander etc.
K108827

Cut and Join Location
K108828

Cut Location for Supply Parts

a.

Be careful when cutting as foamed sealing material is located near the cutting position.

K145508C01
0,0 0,0 false
K108840

Foamed Sealing Material - -


K140309C04
3.938,0.49 4.25,0.646 0.313,0.156 10 false *a
*a 20 mm (0.79 in.) - -


K145524C01
1.844,3.063 2.156,3.219 0.313,0.156 10 false *a
*a 315 mm (12.40 in.) - -


K145525

K140312C04
0.719,0.844 1.031,1 0.313,0.156 10 false *a 4.156,0.865 4.469,1.021 0.313,0.156 10 false *a 0.271,0.26 0.583,0.417 0.313,0.156 10 false *A 3.688,0.26 4,0.417 0.313,0.156 10 false *B
*A PATTERN 1 *B PATTERN 2
*a 30 mm (1.18 in.) - -
K111603

Laser Screw Welding - -



b.

When replace only the outer panel, please cut off a necessary range depending on a damage range.

i.

Carefully cut the outer panel so not to damage the reinforcement.


ii.

Make sure that butt welding does not heat-affect the reinforcement when welding the outer panel.




INSTALLATION


Symbol Meaning
K108821

Spot Weld
K108823

Plug Weld
K108825

Plug Weld
K108830

Fillet Weld
K108831

Butt Weld

a.

Inspect the fitting of the related parts around the new parts before welding. This affects the appearance of the finish.


b.

Temporarily install the new parts and measure each part of the new parts in accordance with the body dimension diagram. (See the body dimensions)


c.

Weld the No. 3 inner pillar sub-assembly to the vehicle side.

K143869C01
2.01,1.865 2.313,1.646 2.313,1.646 2.552,1.646 false 5.427,1.875 5.729,1.656 5.729,1.656 5.969,1.656 false 0.25,0.25 0.563,0.406 0.313,0.156 10 false *A 3.688,0.26 4,0.417 0.313,0.156 10 false *B 2.594,1.552 2.906,1.708 0.313,0.156 10 false *1 0.958,4.5 1.271,4.656 0.313,0.156 10 false *a 1.208,2.802 1.521,2.958 0.313,0.156 10 false *b 2.479,2.76 2.792,2.917 0.313,0.156 10 false *b 6,1.573 6.313,1.729 0.313,0.156 10 false *1
*A PATTERN 1 *B PATTERN 2
*1 NO. 3 INNER PILLAR SUB-ASSEMBLY - -
*a 10 mm (0.39 in.) *b 17 mm (0.67 in.)
K111603

Laser Screw Welding - -



d.

Weld the center body pillar reinforce sub-assembly upper to the vehicle side.

K145526C01
4.156,2.25 5.083,1.958 5.083,1.958 5.5,1.958 false 5.563,1.875 5.875,2.031 0.313,0.156 10 false *1
*1 CENTER BODY PILLAR REINFORCE SUB-ASSEMBLY UPPER - -
K111603

Laser Screw Welding - -


K143870


e.

Be careful when welding as foamed sealing material is located near the area that is cut and joined together.

K145508C02
0,0 0,0 false
K108840

Foamed Sealing Material - -



f.

Weld the rocker panel outer to the vehicle side.

K145527C01
2.302,2.083 2.729,2.083 2.729,2.083 3.583,2.406 false 2.115,1.99 2.427,2.146 0.313,0.156 10 false *1
*1 ROCKER PANEL OUTER - -
K111603

Laser Screw Welding - -



g.

After welding, apply the foamed sealing material to the corresponding parts. (See the painting/coating)


h.

After welding, apply body sealer to the corresponding parts. (See the painting/coating)


i.

After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.