Home › General › INTRODUCTION › WHEN REMOVING,INSTALLING,REPAIRING OR REPLACING PARTS › 2019.02–2020.08
BM33C0E _V1 General _068299 INTRODUCTION _0332869 WHEN REMOVING,INSTALLING,REPAIRING OR REPLACING PARTS F

INTRODUCTION  WHEN REMOVING,INSTALLING,REPAIRING OR REPLACING PARTS  WHEEL ALIGNMENT STANDARD  


The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after completing the front wheel alignment procedure are shown below.

Necessary Procedures After Procedure Performed
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed
Front wheel alignment adjustment
1.

Clear zero point calibration data.

2.

Perform yaw rate and acceleration sensor zero point calibration.


·

DTCs are stored

·

ABS warning light illuminates

·

Brake warning light / yellow (minor malfunction) illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions



MEASURE VEHICLE HEIGHT


NOTICE:
·

Before inspecting the wheel alignment, adjust the vehicle height to the specified value.

·

Be sure to perform measurement on a level surface.

·

If it is necessary to go under the vehicle for measurement, confirm that the parking brake is applied and the vehicle is secured with chocks.

·

Inspect while the vehicle is unloaded.

·

The standard value shown here is a value that is used for performing a wheel alignment and does not indicate the height of an actual vehicle.



a.

Bounce the vehicle up and down at the corners to stabilize the suspension.


b.
C370166N01
0.844,1.125 1,1.323 0.156,0.198 10 false A 2.406,1.198 2.563,1.396 0.156,0.198 10 false B 0.813,3.99 0.969,4.188 0.156,0.198 10 false C 2.375,4.031 2.531,4.229 0.156,0.198 10 false D

Measure the vehicle height.

Measurement Points:

A: Ground clearance of front wheel center


B: Ground clearance of center of bolt head of front lower No. 2 suspension arm bushing (rear bolt of front lower No. 1 suspension arm sub-assembly).


C: Ground clearance of rear wheel center


D: Ground clearance of center of bolt head of rear No. 2 suspension arm assembly and rear suspension member sub-assembly.


Vehicle Height (Unloaded Vehicle) (except Rough Road Area Specification):
Suspension Type Tire Size Front A - B Rear C - D
NORMAL 205/65R16 147 mm (5.79 in.) 47 mm (1.85 in.)
215/55R17 147 mm (5.79 in.) 47 mm (1.85 in.)
235/45R18 147 mm (5.79 in.) 47 mm (1.85 in.)
SPORT 215/55R17 148 mm (5.83 in.) 52 mm (2.05 in.)
235/45R18 148 mm (5.83 in.) 52 mm (2.05 in.)


Vehicle Height (Unloaded Vehicle) (for Rough Road Area Specification):
Suspension Type Tire Size Front A - B Rear C - D
NORMAL 215/55R17 134 mm (5.28 in.) 39 mm (1.54 in.)
235/45R18 134 mm (5.28 in.) 39 mm (1.54 in.)




INSPECT CAMBER, CASTER AND STEERING AXIS INCLINATION (FRONT WHEEL ALIGNMENT)


NOTICE:

Inspect while the vehicle is unloaded.


a.
C132440C16
2.396,1.104 2.51,0.823 2.51,0.823 2.74,0.823 false 0.604,0.708 1.031,0.708 1.031,0.708 1.031,1.458 false 2.76,0.729 2.99,0.906 0.229,0.177 10 false *b 0.448,0.604 0.688,0.781 0.24,0.177 10 false *a
*a Turning Radius Gauge
*b Camber-caster-kingpin Gauge


Install a camber-caster-kingpin gauge and place the front wheels on the center of a turning radius gauge.


b.

Inspect the camber, caster and steering axis inclination.

Camber (Unloaded Vehicle) (except Rough Road Area Specification):
Suspension Type Tire Size Camber Inclination Right-left Difference
NORMAL 205/65R16 -0°30' +/- 0°45' (-0.50° +/- 0.75°) 0°45' (0.75°) or less
215/55R17 -0°30' +/- 0°45' (-0.50° +/- 0.75°)
235/45R18 -0°30' +/- 0°45' (-0.50° +/- 0.75°)
SPORT 215/55R17 -0°30' +/- 0°45' (-0.50° +/- 0.75°)
235/45R18 -0°30' +/- 0°45' (-0.50° +/- 0.75°)


Camber (Unloaded Vehicle) (for Rough Road Area Specification):
Suspension Type Tire Size Camber Inclination Right-left Difference
NORMAL 215/55R17 -0°20' +/- 0°45' (-0.33° +/- 0.75°) 0°45' (0.75°) or less
235/45R18 -0°20' +/- 0°45' (-0.33° +/- 0.75°)


Caster (Unloaded Vehicle) (except Rough Road Area Specification):
Suspension Type Tire Size Caster Inclination Right-left Difference
NORMAL 205/65R16 5°20' +/- 0°45' (5.33° +/- 0.75°) 0°45' (0.75°) or less
215/55R17 5°20' +/- 0°45' (5.33° +/- 0.75°)
235/45R18 5°20' +/- 0°45' (5.33° +/- 0.75°)
SPORT 215/55R17 5°25' +/- 0°45' (5.42° +/- 0.75°)
235/45R18 5°25' +/- 0°45' (5.42° +/- 0.75°)


Caster (Unloaded Vehicle) (for Rough Road Area Specification):
Suspension Type Tire Size Caster Inclination Right-left Difference
NORMAL 215/55R17 5°20' +/- 0°45' (5.33° +/- 0.75°) 0°45' (0.75°) or less
235/45R18 5°20' +/- 0°45' (5.33° +/- 0.75°)


Steering Axis Inclination (Unloaded Vehicle) (except Rough Road Area Specification):
Suspension Type Tire Size Steering Axis Inclination Reference
NORMAL 205/65R16 12°50' (12.83°)
215/55R17 12°50' (12.83°)
235/45R18 12°50' (12.83°)
SPORT 215/55R17 12°50' (12.83°)
235/45R18 12°50' (12.83°)


Steering Axis Inclination (Unloaded Vehicle) (for Rough Road Area Specification):
Suspension Type Tire Size Steering Axis Inclination Reference
NORMAL 215/55R17 12°30' (12.50°)
235/45R18 12°30' (12.50°)




INSPECT TOE-IN (FRONT WHEEL ALIGNMENT)


NOTICE:

Inspect while the vehicle is unloaded.


a.

Bounce the vehicle up and down at the corners to stabilize the suspension.


b.

Release the parking brake and move the shift lever to N.


c.

Push the vehicle straight ahead approximately 5 m (16.4 ft.). (Step C)


d.
C188968C01
0.833,0.583 0.833,1.115 false 1.365,0.583 1.365,0.99 1.365,0.99 0.833,0.99 false 2.521,1.333 2.521,1.667 false 0.74,1.135 0.917,1.302 0.177,0.167 10 *a 2.427,1.698 2.604,1.854 0.177,0.156 10 *b
*a Tread Center Mark
*b Dimension B
V100135

Front of the Vehicle


Put tread center marks on the rearmost points of the front wheels and measure the distance between the marks (dimension B).


e.

Slowly push the vehicle straight ahead to cause the front wheels to rotate 180°. Use the front tire valve as a reference point.

HINT:

Do not allow the wheels to rotate more than 180°. If the wheels rotate more than 180°, perform the procedure from step C again.



f.
C188969C01
0.646,1.271 0.646,1.635 false 1.917,0.542 2.052,0.698 0.135,0.156 10 C 3.073,0.552 3.208,0.708 0.135,0.156 10 D 2.5,0.719 2.635,0.875 0.135,0.156 10 A 2.51,1.542 2.646,1.698 0.135,0.156 10 B 0.563,1.656 0.74,1.813 0.177,0.156 10 *a
*a Dimension A
V100135

Front of the Vehicle


Measure the distance between the tread center marks on the front of the wheels (dimension A).

Toe-in (Unloaded Vehicle) (except Rough Road Area Specification):
Suspension Type Tire Size Specified Condition
NORMAL 205/65R16 C + D: 0°11' +/- 0°10' (0.19° +/- 0.17°)
A - B: 2.2 +/- 2.0 mm (0.0866 +/- 0.0787 in.)
215/55R17 C + D: 0°11' +/- 0°10' (0.19° +/- 0.17°)
A - B: 2.2 +/- 2.0 mm (0.0866 +/- 0.0787 in.)
235/45R18 C + D: 0°11' +/- 0°10' (0.19° +/- 0.17°)
A - B: 2.2 +/- 2.0 mm (0.0866 +/- 0.0787 in.)
SPORT 215/55R17 C + D: 0°10' +/- 0°10' (0.17° +/- 0.17°)
A - B: 2.0 +/- 2.0 mm (0.0787 +/- 0.0787 in.)
235/45R18 C + D: 0°10' +/- 0°10' (0.17° +/- 0.17°)
A - B: 2.0 +/- 2.0 mm (0.0787 +/- 0.0787 in.)


Toe-in (Unloaded Vehicle) (for Rough Road Area Specification):
Suspension Type Tire Size Specified Condition
NORMAL 215/55R17 C + D: 0°12' +/- 0°10' (0.21° +/- 0.17°)
A - B: 2.4 +/- 2.0 mm (0.0945 +/- 0.0787 in.)
235/45R18 C + D: 0°12' +/- 0°10' (0.21° +/- 0.17°)
A - B: 2.4 +/- 2.0 mm (0.0945 +/- 0.0787 in.)


HINT:

Measure "B - A" only when "C + D" cannot be measured.


If the toe-in is not within the specified range, adjust it at the steering rack ends.



INSPECT WHEEL ANGLE (FRONT WHEEL ALIGNMENT)


a.
C132439C03
0.863,0.204 1.036,0.381 0.173,0.177 10 *b 0.538,0.204 0.713,0.381 0.176,0.177 10 *a 2.397,0.204 2.57,0.381 0.173,0.177 10 *b 2.725,0.204 2.901,0.381 0.176,0.177 10 *a
*a Inside
*b Outside
V100135

Front of the Vehicle


Put tread center marks on the rearmost points of a turning radius gauge.


b.

Turn the steering wheel fully to the left and right and measure the turning angle.

NOTICE:

Inspect while the vehicle is unloaded.


Wheel Turning Angle (Unloaded Vehicle) (except Rough Road Area Specification):
Suspension Type Tire Size Inside Wheel Outside Wheel
NORMAL 205/65R16 38°15' +/- 2°00' (38.25° +/- 2.00°) 32°50' (32.83°)
215/55R17 38°15' +/- 2°00' (38.25° +/- 2.00°) 32°50' (32.83°)
235/45R18 36°55' +/- 2°00' (36.92° +/- 2.00°) 32°00' (32.00°)
SPORT 215/55R17 38°15' +/- 2°00' (38.25° +/- 2.00°) 32°50' (32.83°)
235/45R18 36°55' +/- 2°00' (36.92° +/- 2.00°) 31°55' (31.92°)


Wheel Turning Angle (Unloaded Vehicle) (for Rough Road Area Specification):
Suspension Type Tire Size Inside Wheel Outside Wheel
NORMAL 215/55R17 38°40' +/- 2°00' (38.67° +/- 2.00°) 33°05' (33.08°)
235/45R18 37°20' +/- 2°00' (37.33° +/- 2.00°) 32°15' (32.25°)


If the right and left inside wheel angles differ from the specified value, check and adjust the right and left steering rack end lengths.




Necessary Procedures After Procedure Performed
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed
Rear wheel alignment adjustment
1.

Clear zero point calibration data.

2.

Perform yaw rate and acceleration sensor zero point calibration.


·

DTCs are stored

·

ABS warning light illuminates

·

Brake warning light / yellow (minor malfunction) illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions



INSPECT CAMBER (REAR WHEEL ALIGNMENT)


NOTICE:

Inspect while the vehicle is unloaded.


a.
C107736C10
2.052,1.26 2.375,1.26 false 2.406,1.167 2.656,1.385 0.25,0.219 10 *a
*a Camber-caster-kingpin Gauge


Install a camber-caster-kingpin gauge.


b.

Inspect the camber.

Camber (Unloaded Vehicle) (except Rough Road Area Specification):
Suspension Type Tire Size Camber Inclination Right-left Difference
NORMAL 205/65R16 -1°05' +/- 0°45' (-1.08° +/- 0.75°) 0°45' (0.75°) or less
215/55R17 -1°05' +/- 0°45' (-1.08° +/- 0.75°)
235/45R18 -1°05' +/- 0°45' (-1.08° +/- 0.75°)
SPORT 215/55R17 -1°10' +/- 0°45' (-0.83° +/- 0.75°)
235/45R18 -1°10' +/- 0°45' (-0.83° +/- 0.75°)


Camber (Unloaded Vehicle) (for Rough Road Area Specification):
Suspension Type Tire Size Camber Inclination Right-left Difference
NORMAL 215/55R17 -0°55' +/- 0°45' (-0.92° +/- 0.75°) 0°45' (0.75°) or less
235/45R18 -0°55' +/- 0°45' (-0.92° +/- 0.75°)


HINT:

Camber is not adjustable. If the measurement is not within the specified range, inspect the suspension parts for damage and/or wear, and replace them if necessary.




INSPECT TOE-IN (REAR WHEEL ALIGNMENT)


NOTICE:

Inspect while the vehicle is unloaded.


a.

Bounce the vehicle up and down at the corners to stabilize the suspension.


b.

Release the parking brake and move the shift lever to N.


c.

Push the vehicle straight ahead approximately 5 m (16.4 ft.). (Step A)


d.
C188968C02
0.83,0.579 0.83,1.114 false 1.361,0.579 1.361,0.992 1.361,0.992 0.83,0.992 false 0.739,1.134 0.912,1.302 0.173,0.168 10 *a 2.432,1.697 2.607,1.858 0.176,0.161 10 *b 2.522,1.33 2.522,1.671 false
*a Tread Center Mark
*b Dimension B
V100135

Front of the Vehicle


Put tread center marks on the rearmost points of the rear wheels and measure the distance between the marks (dimension B).


e.

Slowly push the vehicle straight ahead to cause the rear wheels to rotate 180°. Use the rear tire valve as a reference point.

HINT:

Do not allow the wheels to rotate more than 180°. If the wheels rotate more than 180°, perform the procedure from step A again.



f.
C188969C02
0.646,1.271 0.646,1.635 false 1.917,0.542 2.052,0.698 0.135,0.156 10 C 3.073,0.552 3.208,0.708 0.135,0.156 10 D 2.5,0.719 2.635,0.875 0.135,0.156 10 A 2.51,1.542 2.646,1.698 0.135,0.156 10 B 0.563,1.656 0.74,1.813 0.177,0.156 10 *a
*a Dimension A
V100135

Front of the Vehicle


Measure the distance between the tread center marks on the front of the rear wheels (dimension A).

Camber (Unloaded Vehicle) (except Rough Road Area Specification):
Suspension Type Tire Size Camber Inclination Right-left Difference
NORMAL 205/65R16 -1°05' +/- 0°45' (-1.08° +/- 0.75°) 0°45' (0.75°) or less
215/55R17 -1°05' +/- 0°45' (-1.08° +/- 0.75°)
235/45R18 -1°05' +/- 0°45' (-1.08° +/- 0.75°)
SPORT 215/55R17 -1°10' +/- 0°45' (-0.83° +/- 0.75°)
235/45R18 -1°10' +/- 0°45' (-0.83° +/- 0.75°)


Camber (Unloaded Vehicle) (for Rough Road Area Specification):
Suspension Type Tire Size Camber Inclination Right-left Difference
NORMAL 215/55R17 -0°55' +/- 0°45' (-0.92° +/- 0.75°) 0°45' (0.75°) or less
235/45R18 -0°55' +/- 0°45' (-0.92° +/- 0.75°)


HINT:

Measure "B - A" only when "C + D" cannot be measured.


If the toe-in is not within the specified range, adjust it at the rear suspension toe adjust cam sub-assembly.