Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID BATTERY SYSTEM
NM33C0E _51 Engine / Hybrid System _067713 HYBRID / BATTERY CONTROL _0330464 HYBRID BATTERY SYSTEM CO CONTROL F

HYBRID / BATTERY CONTROL  HYBRID BATTERY SYSTEM  CONTROL  HYBRID VEHICLE CONTROL ECU  


SYSTEM CONTROL


a.

State Of Charge (SOC)

i.

The hybrid vehicle control ECU assembly estimates the SOC of the HV battery from the accumulated amperage that is constantly and repeatedly being charged and discharged. In order to maintain the SOC at the appropriate level all the time, the hybrid vehicle control ECU assembly controls the hybrid system optimally.

W101107E07
1.917,1.958 1.917,0.875 1.917,0.875 1.667,0.875 true 2.917,1.792 2.917,0.792 2.917,0.792 3.25,0.792 true 0.385,0.76 1.688,1.073 1.302,0.313 10 SOC Control Target 3.333,0.688 5.125,1.021 1.792,0.333 10 Example of change in SOC 0.427,1.844 0.833,2.208 0.406,0.365 10 SOC 2.25,2.76 2.729,3.073 0.479,0.313 10 Time 5.323,1.521 6.927,1.865 1.604,0.344 10 Upper SOC Control Limit 5.198,1.865 6.333,2.219 1.135,0.354 10 Control Region 5.323,2.24 6.917,2.656 1.594,0.417 10 Lower SOC Control Limit



b.

Detection of Insulation Resistance Decrease

i.

The leak detection circuit is built into the battery smart unit (battery voltage sensor). The leak detection circuit constantly monitors that the insulation resistance between high-voltage circuits and body ground is maintained.


ii.

The hybrid vehicle control ECU assembly determines decreases in the insulation resistance based on the information from the battery smart unit (battery voltage sensor).


iii.

The leak detection circuit has an AC source and causes a small amount of AC to flow to the high-voltage circuit (positive and negative).


iv.

The more insulation resistance decreases, the more voltage steps down at the detection resistor and the lower the waves of AC. The insulation resistance value is detected based on the amplitude of AC waves.

W101611E40
0.51,0.219 2.219,0.594 1.708,0.375 10 false Hybrid Vehicle Control ECU Assembly 3.844,0.229 5.823,0.49 1.979,0.26 10 false Combination Meter Assembly 2.594,0.677 3.542,1.24 0.948,0.563 10 false CAN Communication Line 3.885,1.917 4.938,2.135 1.052,0.219 10 false HV Battery 0.833,2.781 1.646,3 0.813,0.219 10 false AC Source 5.115,2.865 7.125,3.083 2.01,0.219 10 false Insulation Resistance 3.26,1.25 4.625,1.469 1.365,0.219 10 false High-voltage Circuit 0.833,1.844 2,2.063 1.167,0.219 10 false Voltage Detection 0.771,3.167 3.813,3.49 3.042,0.323 10 false Battery Smart Unit (Battery Voltage Sensor) 0.844,2.396 2.115,2.615 1.271,0.219 10 false Detection Resistor 5.313,1.615 6.521,1.844 1.208,0.229 10 false High-voltage Load 1.448,1.385 3.031,1.635 1.583,0.25 10 false Serial Communication



c.

Cut-off of High-Voltage Circuits during Collision

i.

If the vehicle is involved in a collision as described below, the hybrid vehicle control ECU assembly will shut down the power supply by turning the system main relays off for safety.


ii.

The hybrid vehicle control ECU assembly receives the airbag deployment signal from the airbag sensor assembly during a frontal collision, side collision or rear collision.

W132097E05
0.385,0.792 1.479,1.094 1.094,0.302 10 false Frontal Collision 0.427,1.823 1.438,2.167 1.01,0.344 10 false Side Collision 0.219,2.177 1.542,2.531 1.323,0.354 10 false Rear Side Collision 1.958,1.729 2.875,1.927 0.917,0.198 10 false Impact 3.094,1.063 3.99,1.76 0.896,0.698 10 false Airbag Sensor Assembly 5.156,1.052 6.875,1.74 1.719,0.688 10 false Hybrid Vehicle Control ECU Assembly 4.052,1.5 5,2.052 0.948,0.552 10 false CAN Communication Line