OUTLINE
Exterior Light
The exterior lights consist of the following:
| *A | Models with Front Fog Light | - | - |
| *1 | Side Turn Signal Light Assembly | *2 | Headlight Assembly |
| *3 | Front Fog Light | - | - |
| *a | The illustrations shown are examples only. | - | - |
| *a | Clearance Light/Daytime Running Light | *b | Front Turn Signal Light |
| *c | Low Beam/High Beam | - | - |
| *1 | Center Stop Light Assembly | *2 | Rear Combination Light Assembly |
| *3 | Rear Light Assembly | *4 | License Plate Light Assembly |
| *A | Models with Rear Fog Light | - | - |
| *a | Taillight | *b | Rear Side Marker Light |
| *c | Rear Turn Signal Light | *d | Taillight/Stop Light |
| *e | Back-up Light | *f | Rear Fog Light |
The rear fog light is installed to the driver side of the vehicle.
Daytime Running Light System
The daytime running light system is designed to automatically illuminate the Light Emitting Diode (LED) lights during the daytime to keep the vehicle highly visible to other vehicles.
Light Auto Turn-off System
The light auto turn-off system is used to prevent the driver from leaving the vehicle with the headlights, clearance lights, front side marker lights, taillights, rear side marker lights or license plate lights on.
Automatic Light Control System
When the light control switch is in the AUTO position, the automatic light control sensor detects the ambient light level and automatically turns the headlights, clearance lights, front side marker lights, taillights, rear side marker lights or license plate lights on or off accordingly.
This system is controlled by the main body ECU (multiplex network body ECU).
Automatic Headlight Beam Level Control System
When the headlights are on, the automatic headlight beam level control system operates the headlight leveling motors in accordance with movement of the vehicle.
Emergency Brake Signal
The hazard warning lights flash automatically in the case of emergency braking to alert following drivers, thus helping to reduce rear-end accidents.
Automatic High Beam System
The automatic high beam system detects lights in front of the vehicle and automatically changes between high beams and low beams to support the driver during night driving.
Lane Change Flasher System
The lane change flasher system flashes the turn signal light a certain number of times when the turn signal switch is moved to the lane change position. By using the lane change flasher system when changing lanes, it is no longer necessary to hold the turn signal switch in the lane change position.
SPECIFICATION
| Light | Type | Wattage | |
|---|---|---|---|
|
*1: Models with front fog light *2: Models with rear fog light |
|||
| Headlight Assembly LH/RH | Low Beam/High Beam | LED x 1 | 29/34 |
| Front Turn Signal Light | LED x 11 | 10.3 | |
| Clearance Light/Daytime Running Light | LED x 12 | 1.1/18 | |
| Side Turn Signal Light Assembly | LED x 2 | 0.5 | |
| Fog Light Assembly*1 | LED x 2 | 5.9 | |
| Rear Combination Light Assembly LH/RH | Taillight | LED x 3 | 1.6 |
| Rear Side Marker Light | LED x 1 | ||
| Taillight/Stop Light | LED x 10 | 2.6 | |
| Rear Turn Signal Light | LED x 8 | 5.9 | |
| Rear Light Assembly LH/RH | Taillight | LED x 3 | 2.9 |
| Back-up Light | LED x 3 | 1.8 | |
| Rear Fog Light*2 | LED x 2 | 1.4 | |
| Center Stop Light Assembly | LED x 8 | 0.7 | |
| License Plate Light Assembly (LH/RH) | LED x 1 | 0.3 | |
The rear fog light is installed to the driver side of the vehicle.