Home › Vehicle Interior › PRE-COLLISION › PRE-COLLISION SYSTEM › 2017.09–2019.10
NM33C0E _58 Vehicle Interior _068355 PRE-COLLISION _0333260 PRE-COLLISION SYSTEM CO CONTROL F

PRE-COLLISION  PRE-COLLISION SYSTEM  CONTROL  PRE-COLLISION CONTROL  


FUNCTION OF MAIN COMPONENTS


Item Function

*1: Models with camera heater

*2: Models with headup display

Millimeter Wave Radar Sensor Assembly
·

Radiates millimeter wave forward, uses the reflected millimeter waves for detecting the presence of a vehicle ahead, the vehicle-to-vehicle distance, and the relative speed.

·

Determines whether a collision is imminent based on the information received from this sensor and forward recognition camera. It then outputs a brake assist standby request signal and pre-collision braking request signal if required.


Forward Recognition Camera
·

Acquires a video of the area in front of the vehicle, and performs image processing to recognize obstacles or vehicles ahead, and then transmits this information to the millimeter wave radar sensor assembly.

·

Operates the camera heater (forward recognition hood) to remove condensation from the part of the windshield in front of the forward recognition camera.


Camera Heater (Forward Recognition Hood)*1 Heats the sheet heater in accordance with the signals from the forward recognition camera.
Brake Booster with Master Cylinder Assembly Skid Control ECU
·

Receives a brake assist standby request signal from the millimeter wave radar sensor assembly, and switches the brake assist to standby mode. When a master cylinder pressure signal is input, it activates the brake assist.

·

Receives a pre-collision brake request signal from the millimeter wave radar sensor assembly, and then applies the brakes.

·

Transmits vehicle speed signals to the millimeter wave radar sensor assembly.


Combination Meter Assembly PCS Warning Light
·

Flashes or illuminates to warn the driver in accordance with signals from the millimeter wave radar sensor assembly.

·

Flashes when the system is malfunctioning.

·

Illuminates when the pre-collision system is not available due to certain reasons or when pre-collision brake and pre-collision brake assist operation are disabled using the VSC OFF switch.


Master Warning Light Illuminates to warn the driver in accordance with signals from the millimeter wave radar sensor assembly.
VSC OFF Indicator Light Illuminates when in the VSC OFF mode.
Multi-information Display
·

Displays a warning message to inform or warn the driver of the system condition in accordance with signals from the millimeter wave radar sensor assembly.

·

Disables the pre-collision system operation when selected PCS OFF mode in setting display function.

·

Changing the pre-collision warning timing when selected Far/Middle/Near in setting display function.


Buzzer Sounds to warn the driver in accordance with signals from the millimeter wave radar sensor assembly when the system is malfunctioning or the system determines that the possibility of a frontal collision is high.
Meter Mirror Sub-assembly*2 Displays "BRAKE!" on the windshield glass to inform or warn the driver of the system condition in accordance with signals from the millimeter wave radar sensor assembly.
Hybrid Vehicle Control ECU Assembly
·

Detects the shift position signal and accelerator pedal opening angle and sends that information to the millimeter wave radar sensor assembly.

·

Performs hybrid system output control based on information from the millimeter wave radar sensor assembly.


Airbag Sensor Assembly Detects the yaw rate and lateral/longitudinal deceleration of the vehicle and transmits the signal to the millimeter wave radar sensor assembly.
Network Gateway ECU Transmits the signal between the CAN communication bus.
Main Body ECU (Multiplex Network Body ECU) Outputs the specification signal of the vehicle to millimeter wave radar sensor assembly.
Steering Sensor Detects the angle and direction of steering and transmits a signal to the millimeter wave radar sensor assembly, skid control ECU and forward recognition camera.
Speed Sensor Detect the wheel speed of each of the 4 wheels and transmits the signal to the skid control ECU.
Stop Light Switch Assembly Stop Light Relay
·

Detects if the brake pedal is depressed and transmits a signal to the skid control ECU.

·

Illuminates the stop lights in accordance with the signals from the skid control ECU.


Steering Pad Switch Assembly Switch the display of multi-information display within combination meter assembly.
VSC OFF Switch Disables the pre-collision brake and pre-collision brake assist operation when VSC OFF mode.


FUNCTION


a.

The pre-collision system uses a radar sensor and camera sensor to detect vehicles in front of your vehicle.


b.

When the system determines that the possibility of a frontal collision with a vehicle is high, a warning operates to urge the driver to take evasive action and the potential brake pressure is increased to help the driver avoid the collision.


c.

If the system determines that the possibility of a frontal collision with a vehicle is extremely high, the brakes are automatically applied to help avoid the collision or help reduce the impact of the collision.

i.

Pre-collision warning

·

When the system determines that the possibility of a frontal collision is high, a buzzer will sound and a warning message will be displayed on the multi-information display to urge the driver to take evasive action.



ii.

Pre-collision brake assist

·

When the system determines that the possibility of a frontal collision is high, the system applies greater braking force in relation to how strongly the brake pedal is depressed.



iii.

Pre-collision braking

·

When the system determines that the possibility of a frontal collision is high, the system warns the driver. If the system determines that the possibility of a frontal collision is extremely high, the brakes are automatically applied to help avoid the collision or reduce the collision speed.




d.

The pre-collision system can be disabled/enabled and the warning timing can be changed.



OPERATING CONDITIONS


a.

The pre-collision system is enabled and the system determines that the possibility of a frontal collision with a vehicle is high.


b.

Each function is operational at the following speeds:

Pre-collision warning:
·

Vehicle speed is between approximately 10 and 110 mph (15 and 180 km/h).

·

The relative speed between your vehicle and the vehicle ahead is approximately 7 mph (10 km/h) or more.


Pre-collision brake assist:
·

Vehicle speed is between approximately 20 and 110 mph (30 and 180 km/h).

·

The relative speed between your vehicle and the vehicle ahead is approximately 20 mph (30 km/h) or more.


Pre-collision braking:
·

Vehicle speed is between approximately 10 and 110 mph (15 and 180 km/h).

·

The relative speed between your vehicle and the vehicle ahead is approximately 7 mph (10 km/h) or more.


i.

The system may not operate in the following situations:

·

If a 12-volt battery terminal has been disconnected and reconnected and then the vehicle has not been driven for a certain amount of time.

·

If the shift position is in R.

·

If VSC is disabled (only the pre-collision warning function will be operational).




c.

Cancelation of the pre-collision braking

i.

If either of the following occur while the pre-collision braking function is operating, it will be canceled:

·

The accelerator pedal is depressed strongly.

·

The steering wheel is turned sharply or abruptly.




d.

Conditions under which the system may operate even if there is no possibility of a collision.

i.

In some situations such as the following, the system may determine that there is a possibility of a frontal collision and operate.

·

When passing a vehicle.

·

When changing lanes while overtaking a preceding vehicle.

·

When overtaking a preceding vehicle that is changing lanes.

·

When overtaking a preceding vehicle that is making a left/right turn.

Y206028

·

When passing a vehicle in an oncoming lane that is stopped to make a right/left turn.

Y206029

·

When driving on a road where relative location to vehicle ahead in an adjacent lane may change, such as on a winding road.

Y206030

·

When rapidly closing on a vehicle ahead.

·

If the front of the vehicle is raised or lowered, such as when the road surface is uneven or undulating.

·

When approaching objects on the roadside, such as guardrails, utility poles, trees, or walls.

·

When there is a vehicle or object by the roadside at the entrance of a curve.

Y224102

·

When driving on a narrow path surrounded by a structure, such as in a tunnel or on an iron bridge.

·

When there is a metal object (manhole cover, steel plate, etc.), steps, or a protrusion on the road surface or roadside.

·

When passing through a place with a low structure above the road (low ceiling, traffic sign, etc.).

Y186313

·

When passing under an object (billboard, etc.) at the top of an uphill road.

Y190952

·

When rapidly closing on an electric toll gate barrier, parking area barrier, or other barrier that opens and closes.

·

When using an automatic car wash.

·

When driving through or under objects that may contact the vehicle, such as thick grass, tree branches, or a banner.

Y186314

·

When the vehicle is hit by water, snow, dust, etc. from a vehicle ahead.

·

When driving through steam or smoke.

·

When there are patterns or paint on the road or a wall that may be mistaken for a vehicle.

·

When driving near an object that reflects radio waves, such as a large truck or guardrail.

·

When driving near a TV tower, broadcasting station, electric power plant, or other location where strong radio waves or electrical noise may be present.





SYSTEM CONTROL


a.

Pre-collision Brake Assist

i.

When the driver depresses the brake pedal after the pre-collision system has determined that there is the possibility of a collision, brake fluid pressure is increased. If the possibility of a collision is still high, brake fluid pressure is further increased.

Y212889E01
1.354,0.188 2.167,0.531 0.813,0.344 10 false Possibility of collision 2.635,0.198 3.25,0.542 0.615,0.344 10 false Operation of pedal 3.833,0.208 4.792,0.563 0.958,0.354 10 false High possibility of collision 5.198,0.198 5.781,0.375 0.583,0.177 10 false Collision 0.49,0.896 0.833,1.094 0.344,0.198 10 false Time 0.781,1.406 1.656,1.75 0.875,0.344 10 false Normal driving condition 2.01,1.406 2.583,1.594 0.573,0.188 10 false Stand-by 2.948,1.396 4.385,1.917 1.438,0.521 10 false Up hydraulic brake pressurization from pre-collision brake assist 4.583,1.417 5.177,1.969 0.594,0.552 10 false Hydraulic pressure further up 2.969,2.531 4.406,3.073 1.438,0.542 10 false Pressurization starts at the same time of brake pedaling 0.063,3.5 0.625,3.99 0.563,0.49 10 false Brake hydraulic pressure 0.135,4.74 0.552,4.927 0.417,0.188 10 false Speed 2.927,5.146 4.094,5.469 1.167,0.323 10 false Pre-collision Brake Assist 5.24,5.573 7.094,5.927 1.854,0.354 10 false Speed reduction amount when high possibility of collision 5.26,4.813 6.219,5.031 0.958,0.219 10 false Normal braking 5.281,3.844 6.219,4.052 0.938,0.208 10 false Normal braking 5.25,3.323 7.083,3.656 1.833,0.333 10 false Effection of pre-collision brake assist pressurization 5.25,2.656 7.031,2.979 1.781,0.323 10 false Boost oil pressure when high possibility of collision



b.

Pre-collision Braking

i.

When the pre-collision system detects an object such as a vehicle in front of the vehicle and determines that the possibility of a collision is high, the system displays a warning message on the multi-information display, and sounds the buzzer to warn the driver.


ii.

When the pre-collision system determines that a collision is imminent, the system performs pre-collision braking control.

Y183736E16
1.271,1.583 1.438,1.583 1.438,1.583 1.625,1.365 true 2.563,1.594 2.385,1.594 2.385,1.594 2.292,1.385 true 6.01,0.292 6.656,0.625 0.646,0.333 10 false Collision 4.417,0.281 5.802,1 1.385,0.719 10 false Unavoidable collision 2.656,0.271 4.302,0.542 1.646,0.271 10 false High possibility of collision 1.125,0.271 2.5,0.531 1.375,0.26 10 false Possibility of collision 0.385,1.094 0.823,1.323 0.438,0.229 10 false Time 1.021,1.49 1.344,1.75 0.323,0.26 10 false Far 1.729,1.521 2.177,1.781 0.448,0.26 10 false Middle 2.615,1.5 2.938,1.76 0.323,0.26 10 false Near 0.677,2.021 1.573,2.354 0.896,0.333 10 false Normal driving 1.698,2.031 5.354,2.333 3.656,0.302 10 true Warning ("BRAKE!" is displayed and buzzer is sounded)* 3.208,2.5 4.5,2.802 1.292,0.302 10 false Pre-collision Braking 0.104,3.542 0.604,4.042 0.5,0.5 10 false Vehicle speed 6.25,4.521 7.052,4.948 0.802,0.427 10 false Deceleration effect 0.323,5.781 6.708,6.531 6.385,0.75 10 false *: Warning timing can be selected from far, middle or near by operating the steering pad switch assembly and multi-information display.




DIAGNOSIS


a.

Initial Check

i.

The millimeter wave radar sensor assembly performs an initial check on the system for approximately 3 seconds after the power switch has been turned to ON.



b.

Monitor Function

i.

After completing the initial check, the pre-collision system becomes ready to operate. During this time, the millimeter wave radar sensor assembly periodically monitors the system for any malfunctions.



c.

Diagnostic Trouble Code (DTC)

i.

If the millimeter wave radar sensor assembly detects a malfunction in the pre-collision system, it stores a 5 digit Diagnostic Trouble Code (DTC) in memory.