FUNCTION OF MAIN COMPONENTS
| Component | Function | |
|---|---|---|
|
*1: Models with parking assist monitor system *2: Models with headup display |
||
| Clearance Warning ECU Assembly | ·
Judges the approximate distance between the vehicle and an obstacle based on signals from the ultrasonic sensors. Output signals are sent to the combination meter assembly, rear television camera assembly*1 or headup display (meter mirror sub-assembly)*2. ·
Sounds the No. 1 clearance warning buzzer. |
|
| Front Corner Ultrasonic Sensor LH/RH | Detects the distance between the vehicle and an obstacle. | |
| Rear Corner Ultrasonic Sensor LH/RH | ||
| No. 1 Clearance Warning Buzzer | Sounds to inform the driver according to the distance to the obstacle. | |
| Combination Meter Assembly | TOYOTA Parking Assist-sensor Indicator Light | Illuminates to inform the driver when the system operation conditions are met. |
| Multi-information Display | ·
Displays the location of the obstacle and the approximate distance between the vehicle and the obstacle. ·
Displays an indication of a malfunction or freezing of an ultrasonic sensor to inform the driver. ·
The sound volume can be chosen on the setup screen for the TOYOTA parking assist sensor system. |
|
| Master Warning Light | Illuminates in accordance with the indication on the multi-information display. | |
| Combination Meter Assembly | Sends the vehicle speed signal to the clearance warning ECU assembly. | |
| Radio and Display Receiver Assembly | Displays the location of an obstacle and the approximate distance between the vehicle and the obstacle. | |
| Headup Display (Meter Mirror Sub-assembly)*2 | Displays the location of an obstacle and the approximate distance between the vehicle and the obstacle. | |
| Rear Television Camera Assembly*1 | ·
Captures images of the area behind the vehicle. ·
The clearance sonar information is superimposed on the captured image. Then, the image is sent to the radio and display receiver assembly as video signals. |
|
| Steering Pad Switch Assembly | Sends operation signals from switches to the spiral cable sub-assembly. | |
| Spiral Cable Sub-assembly | Sends operation signals from the steering pad switch assembly to the combination meter assembly. | |
| Shift Lever Position Sensor | Sends the shift position signal to the hybrid vehicle control ECU assembly. | |
| Hybrid Vehicle Control ECU Assembly | Sends the shift position signal to the clearance warning ECU assembly. | |
| Air Conditioner Amplifier Assembly | Sends outside temperature information to the clearance warning ECU assembly. | |
| Main Body ECU (Multiplex Network Body ECU) | Sends model destination signal (information to indicate the market the vehicle was built for) to the clearance warning ECU assembly. | |
SYSTEM CONTROL
Detection Area
The detection areas of the ultrasonic sensor are as shown in the following illustration.
These detection areas are applicable when positioning a 60 mm (2.36 in.) diameter pole parallel or perpendicular to the ground. The ranges vary depending on the measuring method and type of obstacle.
| *a | Approximately 650 mm (25.6 in.) | *b | Approximately 500 mm (19.7 in.) |
| *c | Approximately 850 mm (33.5 in.) | *d | Approximately 400 mm (15.7 in.) |
| *e | Approximately 200 mm (7.87 in.) | *f | Approximately 450 mm (17.7 in.) |
| *g | Approximately 600 mm (23.6 in.) | *h | Detection Area |
The ultrasonic sensor side view detection range area (labeled*1) represents the cross section of the top view of the lines of detection range A. The area*1 does not represent the entire side view detection range.
The operating condition of each sensor differs according to its installed position as shown in the table below:
| Installation Position | Operating Condition |
|---|---|
| Front Corner | ·
Power switch is on (IG). ·
System is activated. ·
Shift lever is in a position other than P. ·
Vehicle speed is approximately 10 km/h (6 mph) or less. |
| Rear Corner | ·
Power switch is on (IG). ·
System is activated. ·
Shift lever is in R. ·
Vehicle speed is approximately 10 km/h (6 mph) or less. |
DIAGNOSIS
If a system malfunction is detected, the clearance warning ECU assembly stores Diagnostic Trouble Codes (DTCs) in its memory. For details, refer to the Repair Manual.