Home › Vehicle Exterior › VEHICLE PROXIMITY NOTIFICATION SYSTEM › VEHICLE PROXIMITY NOTIFICATION SYSTEM › 2018.08–2020.08
NM33C0E _59 Vehicle Exterior _075981 VEHICLE PROXIMITY NOTIFICATION SYSTEM _0369610 VEHICLE PROXIMITY NOTIFICATION SYSTEM CO CONTROL F

VEHICLE PROXIMITY NOTIFICATION SYSTEM  VEHICLE PROXIMITY NOTIFICATION SYSTEM  CONTROL  VEHICLE PROXIMITY NOTIFICATION CONTROL  


FUNCTION OF MAIN COMPONENTS


Component Function
Vehicle Approaching Speaker Controller Controls starting and stopping of operation, sound pitch and volume level based on signals received from an hybrid vehicle control ECU assembly, speed sensor and stop light switch.
Vehicle Approaching Speaker Assembly Emits warning sounds based on the operation signal received from the vehicle approaching speaker controller.
Hybrid Vehicle Control ECU Assembly
·

Outputs a signal to the vehicle approaching speaker controller when the shift lever is in P.

·

Outputs an engine running signal to the vehicle approaching speaker controller.


Combination Meter Assembly
·

Outputs a vehicle speed signal to the vehicle approaching speaker controller.

·

Displays a warning message when there is a malfunction in the vehicle proximity notification system.


Stop Light Switch Assembly Outputs a brake pedal state signal to the vehicle approaching speaker controller.


OPERATING CONDITION


Condition Outline
System Active The vehicle proximity notification system operates (emits a warning sound) when either of the following conditions is met:
·

The vehicle speed is 0 km/h (0 mph) or higher, the engine is stopped, the stop light is off and the shift position is other than P.*

·

The vehicle speed is 25 km/h (15 mph) or less, the engine is stopped and the shift position is other than P.


System Stop The vehicle proximity notification system stops operating when any of the following conditions is met:
·

The engine starts.

·

The vehicle speed is more than 25 km/h (15 mph).

·

With a vehicle speed of 0 km/h (0 mph), the stop light on signal is received continuously for more than approximately 1 second.

·

With a vehicle speed of 0 km/h (0 mph), the shift P position signal is received continuously for more than approximately 1 second.

·

With a vehicle speed of 0 km/h (0 mph), the stop light off signal is received continuously for more than approximately 3 seconds (such as when the vehicle is stopped, and in neutral with the parking brake applied).



HINT:

*: When the system is stopped due to a vehicle speed of 0 km/h (0 mph) and the stop light switch assembly off signal is received continuously for more than approximately 3 seconds, the system operates again when any of the following conditions is met:

- A vehicle speed signal of 1 km/h (1 mph) or more is received.

- The brake pedal is operated.




SYSTEM CONTROL


Control Outline

*1: The customizable functions can be turned on or off using the Techstream. For details, refer to the Repair Manual.

*2: When audibility enhancing control is performed, the system starts operating using this control.

Vehicle Speed Linked Control
·

Emits the warning sound by controlling the pitch of the sound in accordance with the vehicle speed.

·

The warning sound becomes higher as the vehicle accelerates and it becomes lower as the vehicle decelerates.


Audibility Enhancing Control*1 When the vehicle proximity notification system is not sounding and the vehicle is stopped (vehicle speed of 0 km/h (0 mph)), if the system operates due to a vehicle speed signal or brake pedal operation (system is changed from being disabled to enabled), the warning sound volume becomes higher than usual for about 1 second to warn people around the vehicle that the vehicle may move.
Fade-in/Fade Out Control When the system starts operating, the warning sound volume gradually increases*2, and when system operation is stopped, the sound volume gradually decreases.


FUNCTION


a.

Warning Indication

i.

The combination meter assembly uses the multi-information display to notify the driver of vehicle proximity notification system malfunctions.


ii.

When the system is not available, the following warning occurs to warn the driver.

When a system malfunction is detected
Multi-information Display Detail DTC
Proximity Notification System Malfunction Visit Your Dealer This message appears when the vehicle approaching speaker controller detects a system malfunction Repair is required DTCs are stored




DIAGNOSIS


a.

The vehicle approaching speaker controller will also store Diagnostic Trouble Codes (DTCs). The DTCs can be read by using the Techstream. For details, refer to the Repair Manual.