Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM › 2018.08–2021.02
NM33C0E _58 Vehicle Interior _068285 HEATING / AIR CONDITIONING _0332682 AIR CONDITIONING SYSTEM CO CONTROL F

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM  CONTROL  AIR CONDITIONING CONTROL  


FUNCTION OF MAIN COMPONENTS


a.

The air conditioning system consists of the following parts:

Component Function

*: Models with 3-zone control

Radio and Display Receiver Assembly Allows operation and adjustment of the air conditioning system via switches.
Cooler Control Switch Assembly*
Air Conditioning Amplifier Assembly Transmits and receives data between the switches and sensors.
Compressor with Motor Assembly Performs suction, compression and discharge of refrigerant gas.
Blower Motor with Fan Sub-assembly High magnetic force magnets and ball bearings are used to achieve a compact and lightweight assembly.
Cooler Condenser Assembly A condenser is used to improve heat exchange efficiency.
Heater Radiator Unit Sub-assembly A Straight Flow Aluminum (SFA)-II heater radiator is used for compactness and high performance.
No. 1 Air Conditioning Radiator Damper Servo Sub-assembly
·

Damper Servo (Mode Switching)

·

Damper Servo (Driver Seat Air Mix)

·

Damper Servo (Front Passenger Seat Air Mix)


·

Controlled by the air conditioning amplifier assembly to move the mode control damper and switch the registers.

·

Controlled by the air conditioning amplifier assembly to move the driver seat air mix control damper.

·

Controlled by the air conditioning amplifier assembly to move the front passenger seat air mix control damper.


No. 2 Air Conditioning Radiator Damper Servo Sub-assembly
·

Damper Servo (Rear Mode Switching)


Driven by the air conditioning amplifier assembly to move the rear mode control damper.
No. 3 Air Conditioning Radiator Damper Servo Sub-assembly*
·

Damper Servo (Passenger Mode Switching)


Controlled by the air conditioning amplifier assembly to move the mode control damper and switch the register.
No. 4 Air Conditioning Radiator Damper Servo Sub-assembly*
·

Damper Servo (Rear Air Mix)


Controlled by the air conditioning amplifier assembly to move the rear air mix control damper.
No. 1 Blower Damper Servo Sub-assembly
·

Damper Servo (Fresh/Recirculation)


Driven by the air conditioning amplifier assembly to move the fresh/recirculation damper.
Evaporator Temperature Sensor (No. 1 Cooler Thermistor) Detects the temperature of the cool air past the no. 1 cooler evaporator sub-assembly and transmits the data to the air conditioning amplifier assembly.
Ambient Temperature Sensor (Thermistor Assembly) Detects ambient temperature and outputs it to the air conditioning amplifier assembly.
Cooler (Room Temperature Sensor) Thermistor Detects room temperature and outputs it to the air conditioning amplifier assembly.
Air Conditioning Thermistor Assembly Detects and sends the temperature of the windshield glass, and temperature and humidity around the windshield glass to the air conditioning amplifier assembly via the main body ECU (multiplex network body ECU).
Automatic Light Control Sensor Detects the changes in the amount of solar energy and outputs them to the air conditioning amplifier assembly via the main body ECU (multiplex network body ECU).
Air Conditioner Pressure Sensor Detects the refrigerant pressure and outputs data to the air conditioning amplifier assembly.
Electric Parking Brake Switch Assembly
·

ECO Switch


Sends the ECO switch on signal to the air conditioning amplifier assembly.
ECM Receives the signals from the engine coolant temperature sensor and transmits them to the air conditioning amplifier assembly.
Hybrid Vehicle Control ECU Assembly
·

Sends the drive mode control signal to the air conditioning amplifier assembly.

·

Controls the compressor with motor assembly in accordance with the state of the air conditioning system and hybrid control system.


Combination Meter Assembly Transmits the vehicle speed signal and front passenger presence signal to the air conditioning amplifier assembly.
Main Body ECU (Multiplex Network Body ECU) Receives the signals from the automatic light control sensor and transmits them to the air conditioning amplifier assembly.



SYSTEM CONTROL


a.

Control List

Control Outline

*1: Models with 3-zone control

*2: If the temperature is set to MAX COLD, the A/C switch and recirculation switch are automatically turned on and remains unchanged in order to improve cooling efficiency. In this case, switch operation is enable by changing the set temperature or turning on either the DEFOGGER switch, the FOOT/DEFFOGER switch or the FOOT switch. (Models for Middle East)

Neural Network Control This control is capable of effecting complex control by artificially simulating the information processing method of the nervous system of living organisms in order to establish a complex input/output relationship that is similar to a human brain.
Outlet Air Temperature Control In compliance with the temperature set at the temperature setting switch, the neural network control calculates the outlet temperature based on the input signals from various sensors. In addition, corrections in accordance with the signals from the evaporator temperature sensor (no. 1 cooler thermistor) and the engine coolant temperature sensor are added to control the outlet air temperature.
Left and Right Independent Control The temperature setting for the driver and front passenger is controlled independently in order to provide a separate vehicle interior temperature for the right and left sides of the vehicle. Thus, air conditioning control that accommodates different occupant preferences has been realized.
3-zone Control*1 The temperature setting for the driver, front passenger and rear passengers is controlled independently in order to provide 3 vehicle interior temperature zones, one each for the driver, front passenger and rear passengers. Thus, air conditioning control that accommodates different occupant preferences has been realized.
Blower Control Controls the blower motor with fan sub-assembly in accordance with the airflow volume that has been calculated by the neural network control based on the input signals from various sensors.
Air Outlet Control Automatically switches the outlets in accordance with the outlet mode ratio that has been calculated by the neural network control based on the input signals from various sensors.
Air Inlet Control (AUTO Mode) Automatically controls the air inlet control damper in accordance with the airflow volume that has been calculated by neural network control.*2
Air Inlet Control (Manual Mode) When the reciculation switch is turned on, it switches to the inside air circulation, and when turned off, it switches to the outside air introduction.
However, depending on the set temperature, the outside air temperature, and the sunlight condition, it may be switched to the inside air circulation automatically to improve the cooling efficiency.*2
ECO Drive Mode Control
·

When ECO drive mode is selected, the air conditioning amplifier assembly enters ECO air conditioning mode.

·

Pressing the ECO air conditioning mode switch cancels the ECO air conditioning mode.


Refrigerant Volume Detection Control Judges a shortage of refrigerant volume based on signals from each sensor and informs the user by turning off the indicator light of the A/C switch.
Compressor Control
·

The air conditioning amplifier assembly calculates the target speed of the compressor based on the target evaporator temperature (which is calculated by the room temperature sensor, ambient temperature sensor (thermistor assembly) and solar sensor) and the actual evaporator temperature that is detected by the evaporator temperature sensor in order to control the compressor speed.

·

Turns the air conditioning on automatically when the AUTO button is pressed when the blower is on and the air conditioning is OFF.

·

Decreases the compressor speed in order to ensure quietness when the vehicle is stopped or the engine is off.


Parking Fresh Control By automatically switching to fresh air mode when the vehicle is parked. Ventilation of the parked vehicle is facilitated and outside air is introduced into the air conditioner unit assembly.
ECO Drive Mode Control When ECO drive mode is selected, the air conditioning amplifier assembly enters ECO air conditioning mode.
Electric Power Control When the vehicle voltage is below the specified level, the air conditioning amplifier assembly saves the power source of some systems in accordance with the voltage signal from the hybrid vehicle control ECU assembly.


b.

Neural Network Control

i.

In the previous automatic air conditioning system, the air conditioning amplifier assembly determined the required outlet air temperature and blower air volume in accordance with a calculation formula that had been obtained based on information received from the sensors. However, because the senses of a person are rather complex, a given temperature is sensed differently depending on the environment in which the person is situated. For example, a given amount of solar radiation can feel comfortably warm in a cold climate, but extremely uncomfortable in a hot climate. Therefore, as a technique for performing a high level of control, a neural network is used in the automatic air conditioning system. With this technique, the data that has been collected under varying environmental conditions is stored in the air conditioning amplifier assembly, which effects control to provide enhanced air conditioning comfort.


ii.

The neural network control consists of neurons in an input layer, an intermediate layer, and an output layer. The input layer neurons process the input data of the ambient temperature, the amount of sunlight and the room temperature based on the signals of the switches and sensors, and output them to the intermediate layer neurons. Based on this data, the intermediate layer neurons adjust the strength of the links among the neurons. The sum of this data is then calculated by the output layer neurons in the form of the required outlet temperature, solar correction, target airflow volume and outlet mode control volume. Accordingly, the air conditioning amplifier assembly controls the servo motors and blower motor with fan sub-assembly in accordance with the control volumes that have been calculated by neural network control.

Y128416E01
2.99,0.073 4.208,0.396 1.219,0.323 10 false Intermediate Layer 3.958,0.385 5.177,0.708 1.219,0.323 10 false Output Layer 2.396,0.385 3.615,0.708 1.219,0.323 10 false Input Layer 4.594,0.74 6.354,1.094 1.76,0.354 10 false Target Output Temperature 1.188,0.74 2.948,1.094 1.76,0.354 10 false Ambient Temperature 1.323,1.406 2.677,1.781 1.354,0.375 10 false Amount of Sunlight 1.333,2.01 2.688,2.385 1.354,0.375 10 false Room Temperature 2.677,3.125 3.177,3.438 0.5,0.313 10 false Control 0.313,4.083 1.448,4.427 1.135,0.344 10 false Input Processing 2.333,3.563 3.531,3.865 1.198,0.302 10 false Neural Networking 2.49,4.104 3.333,4.521 0.844,0.417 10 false Target Outlet Temperature 0.385,5.25 1.198,5.802 0.813,0.552 10 false Temperature Setting 0.375,6.51 1.208,6.823 0.833,0.313 10 false Sensor Input 0.385,7.583 1.219,7.896 0.833,0.313 10 false Switch Input 0.594,8.458 2.698,8.771 2.104,0.313 10 false : Neural network operation range 2.313,4.896 3.5,5.344 1.188,0.448 10 false Amount of Sunlight Correction 2.479,5.698 3.344,6.271 0.865,0.573 10 false Target Airflow Volume 2.51,6.531 3.313,6.823 0.802,0.292 10 false Outlet Mode 2.583,7.281 3.24,7.563 0.656,0.281 10 false Inlet Mode 2.531,7.823 3.375,8.104 0.844,0.281 10 false Compressor 3.969,4.583 5.24,5.052 1.271,0.469 10 false Temperature Control Correction 3.865,5.708 5.365,6.208 1.5,0.5 10 false Various Types of Airflow Volume Corrections 3.906,6.427 5.344,6.938 1.438,0.51 10 false Various Types of Mode Corrections 4.063,7.167 5.135,7.698 1.073,0.531 10 false Various Types of Corrections 5.792,4.094 6.927,4.438 1.135,0.344 10 false Output Correction 5.885,4.635 6.833,5.125 0.948,0.49 10 false Air Mix Control Damper 5.917,5.833 6.813,6.135 0.896,0.302 10 false Blower Motor 5.938,6.438 6.771,6.958 0.833,0.521 10 false Mode Control Damper 5.854,7.146 6.823,7.656 0.969,0.51 10 false Air Inlet Control Damper 5.958,7.875 6.802,8.156 0.844,0.281 10 false Compressor



c.

ECO Drive Mode Control

i.

During ECO drive mode, the air conditioning amplifier assembly restricts air conditioning system performance under specified conditions, thus improving fuel economy.


ii.

The ECO drive mode control is activated when the integration control and panel assembly (drive mode select) is operated, and then restricts air conditioning system performance as described below:

Control Outline
Inside/Outside Air Switch Control If the outside air temperature exceeds a certain limit, the mode switches to inside air recirculation.
Blower Level Control In AUTO mode, the blower level is lowered to the specified value and control is performed. Also, when in warm-up control, the blower level decreases.
Heater and Compressor Control The operation of the heater or the compressor with motor assembly is decreased, to a reserved operation level.



d.

Refrigerant Volume Detection Control

i.

The air conditioning amplifier assembly judges the volume of refrigerant from the ambient temperature, refrigerant pressure and the temperature of the cool air just past the no. 1 cooler evaporator sub-assembly. When the air conditioning amplifier assembly judges that there is a refrigerant shortage, it turns off the indicator light of the A/C switch. At that time, the compressor with pulley assembly stops operating.



e.

Parking Fresh Control

i.

While parking, fresh air introduction mode is automatically selected to enhance ventilation and reduce any odor remaining in the air conditioning unit, thus odor during engine start-up is minimized.

Timing Chart (Sample)
Y167022E20
1.302,2.875 3.688,3.094 2.385,0.219 10 false When last mode is fresh air mode 1.313,3.115 4.198,3.354 2.885,0.24 10 false When last mode is recirculated air mode 1.948,2.302 2.844,2.625 0.896,0.323 10 false Ignition Switch Off 2.969,2.313 3.573,2.542 0.604,0.229 10 false 1 Minute 4.417,2.313 5.344,2.656 0.927,0.344 10 false Ignition Switch ON 5.417,2.323 6.344,2.781 0.927,0.458 10 false Time (min.) 3.365,0.25 4.719,0.667 1.354,0.417 10 false Fresh air introduction while parking mode 1.688,0.365 2.51,0.615 0.823,0.25 10 false Last Mode 0.958,1.031 1.781,1.281 0.823,0.25 10 false Fresh air 0.573,1.542 2.083,1.771 1.51,0.229 10 false Recirculated air 0.094,1.25 0.865,1.479 0.771,0.229 10 false Air Inlet




DIAGNOSIS


a.

The air conditioning amplifier assembly has a self-diagnosis function. It stores any operation malfunctions in the air conditioning system or heater system in memory in the form of Diagnostic Trouble Codes (DTCs). For details, refer to the Repair Manual.