Home › Engine / Hybrid System › A25A-FXS (ENGINE MECHANICAL) › ENGINE UNIT › 2019.02–2020.08
NM33C0E _51 Engine / Hybrid System _067342 A25A-FXS ENGINE MECHANICAL _0328458 ENGINE UNIT GE GENERAL F

A25A-FXS ENGINE MECHANICAL  ENGINE UNIT  GENERAL  GENERAL  


OUTLINE


a.

The A25A-FXS engine is an in-line 4-cylinder, 2.5 liter, 16 valve DOHC engine.


b.

The engine adopts the Dual Variable Valve Timing-intelligent (Dual VVT-i) system which realizes optimal valve timing by using electric motors to actuate the intake camshaft actuators and engine oil pressure to actuate the exhaust camshaft actuators. In addition, this engine uses a high-expansion ratio Atkinson cycle, Direct injection 4-stroke gasoline engine Superior version (D-4S) system, Direct Ignition System (DIS), Electronic Throttle Control System-intelligent (ETCS-i) and Exhaust Gas Recirculation (EGR) system employing a highly efficient EGR cooler. Thus, improved engine performance, quietness, fuel economy and cleaner emissions have been achieved.



SPECIFICATION


Engine Type A25A-FXS

*1: Except models for Australia

*2: Models for Australia

*3: Emission regulations differ depending on the specifications of the vehicle.

*4: The figure shown is the weight of the part without coolant and oil.

No. of Cyls. & Arrangement 4-cylinder, In-line
Valve Mechanism 16-valve DOHC, Chain Drive
(With VVT-iE and VVT-i)
Combustion Chamber Pentroof Type
Flow of Intake and Exhaust Gasses Cross-flow
Fuel System Sequential Multiport Fuel Injection (SFI) D-4S
Ignition System Direct Ignition System (DIS)
Displacement cm3 (cu. in.) 2487 (151.8)
Bore x Stroke mm (in.) 87.5 x 103.4 (3.44 x 4.07)
Compression Ratio 14.0 : 1
Max. Output (EEC) kW@rpm 131@5700
Max. Torque (EEC) N*m@rpm 221@3600 to 5200
Valve Timing Intake Open -34° to 26° BTDC
Closed 114° to 54° ABDC
Exhaust Open 9° to 44° BBDC
Closed 35° to 0° ATDC
Spark Plug Type DENSO Made FC16HR-Q8
Plug Gap mm (in.) 0.7 to 0.8 (0.0276 to 0.0315)
Firing Order 1 - 3 - 4 - 2
Octane Rating 87 or higher
Research Octane Number 91 or higher*1
95 or higher*2
Emission Regulation*3 LEVIII-SULEV30
EURO IV
EURO V
EURO VI
EURO VId-TEMP
Engine Service Mass*4 (Reference) kg (lb) 126.9 (280)

Performance Curve
W139034E01
1.333,2.313 1.792,2.51 0.458,0.198 10 false 160 1.333,2.021 1.792,2.219 0.458,0.198 10 false 180 1.333,1.74 1.792,1.938 0.458,0.198 10 false 200 1.333,1.458 1.792,1.656 0.458,0.198 10 false 220 1.333,1.167 1.792,1.365 0.458,0.198 10 false 240 1.292,0.865 1.75,1.063 0.458,0.198 10 false (N*m) 0.604,1.698 1.135,1.938 0.531,0.24 10 false Torque 2.906,4.344 3.906,4.594 1,0.25 10 false Engine Speed 2.104,3.948 2.479,4.156 0.375,0.208 10 false 1000 2.531,3.948 2.906,4.156 0.375,0.208 10 false 2000 2.958,3.948 3.333,4.156 0.375,0.208 10 false 3000 3.385,3.948 3.76,4.156 0.375,0.208 10 false 4000 3.823,3.948 4.198,4.156 0.375,0.208 10 false 5000 4.25,3.948 4.625,4.156 0.375,0.208 10 false 6000 4.646,3.948 5.021,4.156 0.375,0.208 10 false (rpm) 5.125,3.583 5.5,3.792 0.375,0.208 10 false 0 5.125,3.188 5.5,3.396 0.375,0.208 10 false 20 5.125,2.792 5.5,3 0.375,0.208 10 false 40 5.125,2.417 5.5,2.625 0.375,0.208 10 false 60 5.125,2.031 5.5,2.24 0.375,0.208 10 false 80 5.125,1.656 5.5,1.865 0.375,0.208 10 false 100 5.125,1.25 5.5,1.458 0.375,0.208 10 false 120 5.125,0.865 5.5,1.073 0.375,0.208 10 false 140 5.042,0.615 5.417,0.823 0.375,0.208 10 false (kW) 5.656,2.021 6.229,2.24 0.573,0.219 10 false Output


MAIN FEATURES


a.

The A25A-FXS engine has achieved the following through the use of the items listed in the table below.

i.

High performance and reliability


ii.

Low noise and vibration


iii.

Lightweight and compact design


iv.

Good serviceability


v.

Clean emissions and improved fuel economy

Item i ii iii iv v

○: Applicable

-: Not applicable

*: Models with engine oil cooler (oil cooler assembly)

The high-expansion ratio Atkinson cycle is adopted. ○ - - - ○
Engine Proper An aluminum cylinder block sub-assembly is used. - - ○ - -
Spiny-type liners are used in the cylinder bores. ○ - - - -
A cylinder block water jacket spacer is used. ○ - - - ○
The piston skirt is coated with resin. ○ ○ - - ○
An offset crankshaft is used. ○ ○ - - ○
Laser cladded valve seats are used for the intake side. ○ - - - ○
A resin gear engine balancer assembly is used. - ○ ○ - -
A chain cover that consists of the timing chain cover assembly and No. 2 timing gear cover assembly is used. ○ - - - -
Bolts with smaller heads than standard bolts of the same thread diameter are used. ○ - ○ - -
Valve Mechanism The Variable Valve Timing-intelligent by Electric motor (VVT-iE) system is used for the intake camshafts. ○ - - - ○
The Variable Valve Timing-intelligent (VVT-i) system is used for the exhaust camshafts. ○ - - - ○
A chain sub-assembly and No. 1 chain tensioner assembly are used. - ○ - ○ -
Valve lash adjuster assemblies are used. ○ ○ - ○ -
No. 1 valve rocker arm sub-assemblies are used. ○ - - - ○
Lubrication System A cartridge type oil filter sub-assembly is used. - - - ○ -
An electronically controlled variable displacement oil pump is used. ○ - - - ○
An engine oil level sensor is used. - - - - ○
An engine oil cooler (oil cooler assembly) is used.* ○ - - - -
Cooling System TOYOTA Genuine Super Long Life Coolant (SLLC) is used. - - - ○ -
A variable passage cooling system is used. ○ - - - ○
An electric engine water pump assembly is used. - - - - ○
Intake and Exhaust System An intake manifold made of plastic is used. - ○ ○ - -
A linkless type throttle body with motor assembly is used. - - ○ ○ -
A stainless steel exhaust manifold assembly is used. - - ○ - -
Emission Control System A step motor type Exhaust Gas Recirculation (EGR) valve is used. ○ - - - ○
A water-cooled type Exhaust Gas Recirculation (EGR) cooler is used. ○ - - - ○
An ultra thin-wall, high-cell density ceramic type Three-Way Catalytic converter (TWC) is used. - - - - ○
Fuel System A Direct injection 4-stroke gasoline engine Superior version (D-4S) system is used. ○ - - - ○
A fuel returnless system is used. - - ○ ○ ○
Quick connectors are used to connect the fuel hoses with the fuel pipes. - - - ○ -
10-hole type low pressure port fuel injector assemblies are used. ○ - - - ○
6-hole type high pressure direct fuel injector assemblies are used. ○ ○ - - ○
Ignition System The Direct Ignition System (DIS) is used. ○ - - ○ ○
Long-reach type iridium-tipped spark plugs are used. ○ - - ○ ○
Engine Control System Magnetic Resistance Element (MRE) type camshaft position sensors and crank position sensor are used. ○ - - - ○
The Electronic Throttle Control System-intelligent (ETCS-i) is used. ○ - - - ○
An evaporative emission control system is used. - - - - ○



b.

Location of small-head bolts

W135894

W135895

Models without Engine Oil Cooler (Oil Cooler Assembly)
W135896

Models with Engine Oil Cooler (Oil Cooler Assembly)
W136600