Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM › 2019.02–2021.02
NM33C0E _59 Vehicle Exterior _068036 LIGHTING (EXT) _0331933 LIGHTING SYSTEM CO CONTROL F

LIGHTING (EXT)  LIGHTING SYSTEM  CONTROL  AUTOMATIC HIGH BEAM  


FUNCTION OF MAIN COMPONENTS


Component Function

*1: Except models with automatic headlight beam level control system

*2: Models with automatic headlight beam level control system

Forward Recognition Camera Determines when to turn the high beams on and off after identifying the lights of oncoming vehicles, preceding vehicles and other lights from the picture information of its camera sensor. Then, the sensor sends high beam request signals to the main body ECU (multiplex network body ECU).
Main Body ECU (Multiplex Network Body ECU)
·

Receives a switch on signal from the automatic high beam switch.

·

Receives an AUTO or head position signal and high beam position signal from the steering sensor.

·

Receives the high beam request signal from the forward recognition camera and transmits a signal to DIM relay*1.

·

Receives the high beam request signal from the forward recognition camera and transmits a signal to headlight ECU sub-assembly LH*2.


No. 1 Engine Room Relay Block and No. 1 Junction Block Assembly
·

DIM Relay*1


Supplies power to the high beams.
Headlight ECU Sub-assembly LH/RH*2 Receives the headlight control signal from the main body ECU (multiplex network body ECU) and changes between the high beams and low beams.
Hybrid Vehicle Control ECU Assembly Outputs a signal to indicate that the shift lever is in R. Based on this signal, the forward recognition camera determines the direction of vehicle movement.
Brake Booster with Master Cylinder Assembly
·

Skid Control ECU


Outputs information about the average speed of the driving wheels. This information is used by the forward recognition camera to control switching between the high and low beams of the automatic high beam system.
Combination Meter Assembly
·

Illuminates the automatic high beam indicator to inform the driver when the automatic high beam system is activated.

·

Illuminates the high beam indicator to inform the driver when the high beams are on.

·

Displays a warning message when a malfunction is detected in the automatic high beam system.


Airbag Sensor Assembly Outputs yawrate information.
Automatic Light Control Sensor Detects the ambient light level and transmits a signal to the main body ECU (multiplex network body ECU).
Automatic High Beam Switch Outputs the switch on signal to the main body ECU (multiplex network body ECU).
Turn Signal Switch
·

Light Control Switch

·

Headlight Dimmer Switch


Outputs the light control switch and headlight dimmer switch signal.
Steering Sensor Receives light control switch signal and headlight dimmer switch signal from the turn signal switch and transmits it to the main body ECU (multiplex network body ECU).


SYSTEM CONTROL


Function Operation Condition

*1: Models for Europe

*2: Except models for Europe

Active When all of the following conditions are met, the automatic high beam system is activated and the automatic high beam indicator light turns on:
·

The power switch is on (IG).

·

The light control switch is in the AUTO or HEAD position and the low beam headlights are on.

·

The headlight dimmer switch is in the high beam position.

·

The automatic high beam switch is ON.

·

The shift is in any position other than R.


High Beams on When all of the following conditions are met, the automatic high beam system turns on the high beams after a short delay:
·

Vehicle speed is more than approximately 40 km/h (25 mph).*1

·

Vehicle speed is more than approximately 30 km/h (19 mph).*2

·

The area in front of the vehicle is dark.

·

No oncoming vehicles are present with the headlights on.

·

No preceding vehicles are present with the taillights on.

·

Few streetlights are present along the street ahead.


High Beams off When any of the following conditions is met, the automatic high beam system turns off the high beams after a short delay:
·

Vehicle speed is less than approximately 30 km/h (19 mph).*1

·

Vehicle speed is less than approximately 25 km/h (16 mph).*2

·

The area in front of the vehicle is not dark.

·

An oncoming vehicle with headlights on is detected.

·

A preceding vehicle with taillights on is detected.

·

Several streetlights are present along the street ahead.




FUNCTION


a.

When passing an oncoming vehicle:

·

When the automatic high beam system is operating and an oncoming vehicle is detected within the camera detection area, the high beams turn off.

·

When an oncoming vehicle passes out of camera sensor range, the automatic high beam system turns the high beams on after a short delay.


Y100276C02
5.177,3.229 5.177,3.427 false 3.25,0.375 3.563,0.573 0.313,0.198 10 *a 3.99,1.844 4.302,2.042 0.313,0.198 10 *b 5.146,3.458 5.458,3.656 0.313,0.198 10 *c
*a Detection Area *b Delay
*c Camera Sensor Angle - -


HINT:
·

The detection distance varies depending on detected objects.

·

The timing of turning on and off the high beams varies depending on the intensity of oncoming (and preceding) vehicle lights.




b.

When passing a preceding vehicle:

·

When the automatic high beam system is operating and a preceding vehicle is detected within the camera detection area, the high beams turn off.

·

When a preceding vehicle passes out of camera sensor range, the automatic high beam system turns the high beams on after a short delay.


Y134696C01
4.99,3.5 4.99,3.281 false 3.198,0.438 3.51,0.594 0.313,0.156 10 false *a 2.656,3.406 2.969,3.563 0.313,0.156 10 false *b 4.927,3.542 5.24,3.698 0.313,0.156 10 false *c
*a Detection Area *b Delay
*c Camera Sensor Angle - -


HINT:

The timing of turning on and off the high beams varies depending on the intensity of the preceding vehicle lights.




DIAGNOSIS


a.

When the main body ECU (multiplex network body ECU) detects a malfunction in the automatic high beam control system, Diagnostic Trouble Codes (DTCs) are stored in memory.


b.

The DTCs can be read using the Global TechStream (GTS). For details, refer to the Repair Manual.