Home › Audio / Visual / Telematics › TELEMATICS › TELEMATICS SYSTEM (for eCall) › 2019.02–2021.02
NM33C0E _56 Audio / Visual / Telematics _079890 TELEMATICS _0387679 TELEMATICS SYSTEM(for eCall) CO CONTROL F

TELEMATICS  TELEMATICS SYSTEM(for eCall)  CONTROL  eCall SERVICE  


FUNCTION OF MAIN COMPONENTS


a.

The main components in the eCall system have the following functions:

Component Function

*1: Except models with navigation system (JBL premium model)

*2: Models with navigation system (JBL premium model)

Communication Telematics Box
·

Houses the microphones and speaker.

·

Receives the user's voice through the microphones.

·

Outputs the operators voice of PSAP through the speaker.


Roof Console Box Sub-assembly Houses the manual (SOS) switch.
Major Components of Roof Console Box Sub-assembly Manual (SOS) Switch When pressed, allows the driver to connect to and communicate with the PSAP as an emergency assistance button (SOS) service.
Manual (SOS) Switch Indicator Green
·

Turns on when the system is operating normally.

·

Blinks during a call and turns off when the system is malfunctioning.


Red
·

Illuminates to warn the user when a malfunction occurs in the system.

·

Turns off when the system is operating normally.


Telematics Transceiver (Data Communication Module)
·

Connects to the PSAP and allows the driver to speak with the call center operator when the automatic emergency call service or the manual emergency call service is active.

·

The cellular phone module makes or receives calls.

·

The telematics transceiver (data communication module) receives signals from the GNSS antenna, calculates the position of the vehicle and transmits it to the PSAP.

·

Controls the on/off and blinking actions of the manual (SOS) switch indicator.

·

Dims the manual (SOS) switch indicator when the taillight relay on signal is received.

·

When communicating with PSAP, sends the users voice picked up by the communication telematics box (microphones), and outputs the operators voice through the communication telematics box (speaker).


Mobilephone Battery (Back-up Battery) Is built into the telematics transceiver (data communication module) and supplies power to the telematics transceiver (data communication module) when the automatic emergency call service is activated and the vehicle battery cannot supply power.
Telephone Antenna Assembly Telephone Antenna Is for a cellular phone antenna which is compatible with the transmission and reception of frequency bands of cellular phones. It transmits signals from the telematics transceiver (data communication module) and receives signals from the call center.
GNSS Antenna Receives the signals from GNSS satellites and transmits these signals to the telematics transceiver (data communication module).
Airbag Sensor Assembly Sends an activation signal to the telematics transceiver (data communication module) when the airbags deploy or a collision is detected. (An automatic emergency call service is made.)
Radio and Display Receiver Assembly*1 Receives the mute signal from the telematics transceiver (data communication module) to mute any audio sound.
Stereo Component Amplifier Assembly*2
DLC3 Allows system diagnosis to be performed when Global TechStream (GTS).



FUNCTION


a.

Automatic Emergency Call Service

·

If any of the airbags are deployed due to a serious collision, the telematics transceiver (data communication module) receives the deployment signal from the airbag sensor assembly. After receiving the deployment signal, the telematics transceiver (data communication module) automatically makes an emergency call and transmits the vehicle location and user information to the PSAP closest to the vehicle.

·

The system is then automatically connected to a PSAP and the user can talk to a PSAP operator. The PSAP operator contacts the emergency services when the user is unable to answer.

Automatic Emergency Call Service Image
Y178729C01
1.719,1.448 2.031,1.646 0.313,0.198 10 false *a 3.75,1.323 4.063,1.521 0.313,0.198 10 false *b 5.615,1.198 5.927,1.396 0.313,0.198 10 false *c
*a Airbag Deployment or Collision Detection *b Public Safety Answering Point (PSAP)
*c Ambulance - -




b.

Manual Emergency Call Service

·

By pushing the manual (SOS) switch during an on-road emergency, the telematics transceiver (data communication module) transmits the vehicle location and user information, and calls to the PSAP closest to the vehicle.

·

The PSAP operator determines the level of the emergency based on the vehicle location and from the conversation with the user, and contacts the emergency services if necessary.

Manual Emergency Call Service Image
Y178730C01
1.948,1.365 2.26,1.563 0.313,0.198 10 false *1 4.906,1.354 5.219,1.552 0.313,0.198 10 false *a
*1 Manual (SOS) Switch - -
*a Public Safety Answering Point (PSAP) - -




c.

eCall Mode

There are 3 modes depending on the vehicle status.

Mode Type Available Services

*1: Once activation has started, the system performs the activation process repeatedly until completion. To avoid transmitting radio waves unnecessarily, make sure to perform activation in an eCall service support area.

*2: For some destinations, only eCall Only Mode is available.

Shipping Mode
·

Mode the DCM (telematics transceiver) is in from the factory and during shipping.

·

The power switch can be turned on (IG) without transmitting radio waves.

·

The system will activate if the manual (SOS) switch is pushed and held for 3 seconds when in an eCall service support area in a mobile phone reception area.*1


eCall Only Mode*2 Only eCall functions can be utilized.
Live Mode
·

When activation has completed, the system changes to live mode.

·

All functions of eCall can be utilized in live mode.






DIAGNOSIS


a.

If there is a malfunction in the system, the telematics transceiver (data communication module) stores Diagnostic Trouble Codes (DTCs) in its memory. For details, refer to the Repair Manual.