Home › Suspension › TIRE PRESSURE MONITORING › TIRE PRESSURE WARNING SYSTEM › from 2021.02
NM33C0E _53 Suspension _065793 TIRE PRESSURE MONITORING _0321057 TIRE PRESSURE WARNING SYSTEM DE DETAILS F

TIRE PRESSURE MONITORING  TIRE PRESSURE WARNING SYSTEM  DETAILS  TIRE PRESSURE WARNING VALVE AND TRANSMITTER  


CONSTRUCTION


a.

The tire pressure warning valve and transmitters are integrated in the tire valves. Each transmitter consist of a lithium battery, sensor and transmitter.


b.

Make sure not to damage the urethane covered backside of the transmitter (the surface opposite to the side with the ID code) with anything sharp.


c.

The transmitter directly measures tire pressure, temperature, and centrifugal acceleration.


d.

The transmitter transmits the measured tire inflation pressure and temperature values to the tire pressure warning ECU and receiver on a frequency of 315 MHz.*

*: Models for Taiwan


e.

The transmitter transmits the measured tire inflation pressure and temperature values to the tire pressure warning ECU and receiver on a frequency of 434 MHz.*

*: Except models for Taiwan


f.

Depending on the timing of the data transmission, it may take several minutes to receive the data from the tire pressure warning valve and transmitter.


g.

The ID code is written on the tire pressure warning valve and transmitter.

Models for Taiwan
X141132C01
1.927,1.531 2.625,1 2.625,1 2.823,1 true 1.417,0.75 1.854,0.417 1.854,0.417 2.052,0.417 true 2.115,1.74 2.75,1.271 2.75,1.271 2.948,1.271 true 6.052,1.635 6.458,1.052 6.458,1.052 6.656,1.052 true 2.104,0.323 2.323,0.51 0.219,0.188 10 false *1 2.865,0.906 3.073,1.083 0.208,0.177 10 false *2 3,1.188 3.219,1.406 0.219,0.219 10 false *3 6.708,0.958 6.906,1.135 0.198,0.177 10 false *a
*1 Tire Pressure Warning Valve and Transmitter *2 Valve Core
*3 Valve Cap - -
*a ID Code (Hexadecimal 7 Digits) - -


Except models for Taiwan
X141126C01
2.25,1.781 2.792,0.75 2.792,0.75 2.958,0.75 true 1.531,2.406 1.698,2.406 1.698,2.406 2.104,1.635 true 1.792,2.604 1.958,2.604 1.958,2.604 2.333,1.896 true 2.021,1.49 2.552,0.479 2.552,0.479 2.719,0.479 true 1.667,1.094 2.115,0.302 2.115,0.302 2.281,0.302 true 1.385,0.771 1.74,0.125 1.74,0.125 1.906,0.125 true 5.792,1.646 6.177,0.927 6.177,0.927 6.344,0.927 true 1.958,0.031 2.271,0.188 0.313,0.156 10 false *1 2.333,0.208 2.646,0.365 0.313,0.156 10 false *2 2.771,0.385 3.083,0.542 0.313,0.156 10 false *3 1.354,2.313 1.667,2.469 0.313,0.156 10 false *4 3.01,0.656 3.323,0.813 0.313,0.156 10 false *5 1.625,2.521 1.938,2.677 0.313,0.156 10 false *6 6.396,0.823 6.708,0.979 0.313,0.156 10 false *a
*1 Tire Pressure Warning Valve and Transmitter *2 Grommet
*3 Washer *4 Nut
*5 Valve Core *6 Valve Cap
*a ID Code (Hexadecimal 7 Digits) - -


HINT:
·

The lithium batteries of the tire pressure warning valve and transmitters are non-replaceable. If the battery is depleted, the tire pressure warning valve and transmitter must be replaced. (Battery life: approximately 10 years)

·

When replacing a tire pressure warning valve and transmitter, each of the tire pressure warning valve and transmitter ID codes must be registered. If even one of the tire pressure warning valve and transmitters is replaced, the ID codes of all tire pressure warning valve and transmitters must be registered again. Record all existing ID codes before beginning the process to enter new ID codes.

·

To register an ID code, use the Global TechStream (GTS) to enter the ID code that is indicated on the tire pressure warning valve and transmitter.

·

Be careful not to damage the tire pressure warning valve and transmitters when removing and reinstalling them.

·

Replace the grommet and valve core with new ones when the tire pressure warning valve and transmitter is replaced or removed and reinstalled. This is necessary to ensure sealing performance.

·

When replacing a valve cap, use only the specified cap. If an unspecified cap is used, it may seize to the tire pressure warning valve and transmitter.

·

For details, refer to the Repair Manual.