Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM › from 2021.02
NM33C0E _51 Engine / Hybrid System _065792 CRUISE CONTROL _0321047 DYNAMIC RADAR CRUISE CONTROL SYSTEM CO CONTROL F

CRUISE CONTROL  DYNAMIC RADAR CRUISE CONTROL SYSTEM  CONTROL  CRUISE CONTROL  


FUNCTION OF MAIN COMPONENTS


a.

The main components in the dynamic radar cruise control system have the following functions:

Component Function

*1: Models with full-speed range following function

*2: Models with shift paddle switch (transmission shift switch assembly)

*3: Models with headup display

Millimeter Wave Radar Sensor Assembly Radiates millimeter radar waves forward, uses the reflected waves to detect the presence of a vehicle traveling ahead, the vehicle-to-vehicle distance, and the relative speed, and then sends this information to the forward recognition camera.
Forward Recognition Camera
·

Detects lane markers and objects on the road ahead using the image captured by the camera sensor.

·

While the system is in vehicle-to-vehicle distance control mode, the forward recognition camera detects the vehicle ahead based on signals from the millimeter wave radar sensor assembly and forward recognition camera. Then, the forward recognition camera calculates the acceleration or deceleration rate required in order to attain the target vehicle-to-vehicle distance, and outputs a request signal to the hybrid vehicle control ECU assembly.

·

Controls the supply of electric current to the camera heater when the ambient temperature is low.

·

If the forward recognition camera detects a malfunction in the dynamic radar cruise control system, it will store Diagnostic Trouble Codes (DTCs).


Camera Heater (Forward Recognition Hood) Control is performed by the forward recognition camera to supply electric current and heat the heater, preventing the windshield glass in front of the forward recognition camera from fogging up.
Steering Pad Switch Assembly Cruise Control Switch
·

Turns the cruise control system on and off.

·

Vehicle-to-vehicle distance control mode becomes be activated immediately after the main switch is turned on. The mode shifts to constant speed control mode by pressing and holding the switch more than 1.5 seconds.


CANCEL Switch A cancel signal is output to the hybrid vehicle control ECU assembly when this switch is operated.
+RES Switch The acceleration function and resuming of a preset speed can be performed by operating this switch. A signal is output to the hybrid vehicle control ECU assembly. when this switch is operated.
-SET Switch The deceleration function and vehicle speed setting resume signals are output to the hybrid vehicle control ECU assembly when this switch is operated.
Vehicle-to-vehicle Distance Control Switch While the system is in vehicle-to-vehicle distance control mode, the driver can operate the vehicle-to-vehicle distance control switch to select the vehicle-to-vehicle distance in three levels: long, middle and short.
Hybrid Vehicle Control ECU Assembly
·

Controls the dynamic radar cruise control system in accordance with signals from switches, sensors.

·

If the hybrid vehicle control ECU assembly detects a malfunction in the dynamic radar cruise control system, it will store Diagnostic Trouble Codes (DTCs).


Inverter with Converter Assembly MG ECU Built into the inverter with converter assembly. Controls the motive force of hybrid vehicle transaxle assembly in accordance with signals from the hybrid vehicle control ECU assembly.
Hybrid Vehicle Transaxle Assembly Generates motive force for the front wheels.
Combination Meter Assembly Cruise Control Indicator
·

Based on a cruise control indicator operation signal sent by the hybrid vehicle control ECU assembly, the combination meter assembly illuminates the cruise control indicator (constant speed control mode) or cruise control indicator (vehicle-to-vehicle distance control mode) when the cruise control system has been turned on using the cruise control switch on the steering pad switch assembly.

·

Based on a cruise control indicator operation signal sent by the hybrid vehicle control ECU assembly, the combination meter assembly turns off the cruise control indicator if a malfunction occurs in the cruise control system.


Cruise SET Indicator Cruise SET indicator illuminates when the vehicle speed is set.
Multi-information Display
·

Displays a warning message to alert the driver in accordance with a signal provided by the hybrid vehicle control ECU assembly.

·

During dynamic radar cruise control operation, the multi-information display receives signals from the hybrid vehicle control ECU assembly in order to display the system conditions.


Buzzer
·

Sounds a buzzer when it receives a signal from the hybrid vehicle control ECU assembly to alert the driver that the distance between vehicles is short.

·

If the hybrid vehicle control ECU assembly detects automatic cancel or warning signals while the vehicle is operating under cruise control, this buzzer sounds to inform the driver.


Master Warning Light Comes on when there is a malfunction in the system.
Turn Signal Switch Sends a turn signal command to the hybrid vehicle control ECU assembly.
Steering Sensor Detects the angle and direction of steering and transmits signals to the skid control ECU and hybrid vehicle control ECU assembly.
Airbag Sensor Assembly
·

Yawrate Sensor


Detects the yaw rate of the vehicle and transmits signals to the hybrid vehicle control ECU assembly.
Stop Light Switch Assembly Detects brake pedal depression and transmits its signal to the hybrid vehicle control ECU assembly.
Brake Booster with Master Cylinder Assembly Skid Control ECU
·

While the system is operating in vehicle-to-vehicle distance control mode, the skid control ECU operates the brake actuator in accordance with the brake request signal received from hybrid vehicle control ECU assembly.

·

Applies the brakes in accordance with signals from the hybrid vehicle control ECU assembly.


Brake Actuator Assembly Parking Brake ECU*1 During stop retention control, when parking brake ECU detects that the vehicle is parked through a driver side courtesy light switch signal or driver side seat belt buckle switch signal, or an electric parking brake switch assembly signal is input, the parking brake ECU operates the parking brake, then the dynamic radar cruise control system is canceled.
Electric Parking Brake Switch Assembly*1 Sends a parking brake application signal to the parking brake ECU.
Parking Brake Actuator Assembly LH/RH*1 Operates the parking brake actuator assembly according to signals from the parking brake ECU.
ECM Actuates the throttle control motor in accordance with the signals from the hybrid vehicle control ECU assembly.
Throttle Body with Motor Assembly Throttle Control Motor Adjusts the throttle valve opening angle in accordance with signals from the ECM.
Throttle Position Sensor Detects the throttle valve opening angle and outputs it to the ECM.
Shift Lever Position Sensor Detects the shift lever position and transmits signals to the hybrid vehicle control ECU assembly.
Shift Paddle Switch (Transmission Shift Switch Assembly)*2 While the vehicle is being driven in D mode or S mode, this switch outputs a signal to the hybrid vehicle control ECU assembly when the switch is pulled to "+" or "-".
Accelerator Pedal Sensor Assembly Detects the accelerator pedal depression angle and transmits it to the hybrid vehicle control ECU assembly.
VSC OFF Switch Detects the VSC OFF or TRC OFF signals and outputs it to the skid control ECU.
Meter Mirror Sub-assembly*3 The headup display receives signals from the combination meter assembly in order to display the system conditions.
Central Gateway ECU (Network Gateway ECU) Gateway function of CAN communication.



FUNCTION


a.

Function List

i.

The control of the dynamic radar cruise control system varies depending on the mode:

A: Constant speed control mode

B: Vehicle-to-vehicle distance control mode

C: Vehicle-to-vehicle distance control mode (Models with full-speed range following function)

Function Outline Mode
A B C

*1: Models with dynamic radar cruise control with road sign assist

*2: Models with shift paddle switch (transmission shift switch assembly)

○: Available

-: Not Available

Constant Speed Control The hybrid vehicle control ECU assembly compares the actual vehicle speed and the set speed and if the vehicle speed is lower than the set speed, it uses the throttle control motor to increase the throttle valve opening angle. ○ ○ ○
Deceleration Control Performs throttle control and brake control in order to decelerate the vehicle so that the vehicle-to-vehicle distance between the driver's own vehicle and the vehicle ahead equals the set distance. - ○ ○
Follow-up Control After performing deceleration control, the driver's own vehicle follows the vehicle ahead in order to maintain the proper vehicle-to-vehicle distance in accordance with the vehicle speed. - ○ ○
Acceleration Control Accelerates the vehicle in order to attain the set vehicle speed if the vehicle ahead or the driver's own vehicle has changed lanes. - ○ ○
Stop Control Detects if the vehicle ahead has stopped, performs motive force control and stops the vehicle while maintaining proper vehicle-to-vehicle distance. - - ○
Stop Retention Control Judges if the vehicle is stopped, performs brake control and keeps the vehicle stopped through the brake hold function. - - ○
Start Control Detects that the vehicle ahead starts moving again, displays the message on the multi-information display to urge the driver to perform the start-off operation (to operate the +RES switch on the steering pad switch assembly or depress the accelerator pedal), and resumes follow-up control after the vehicle is started. - - ○
Turn signal-linked Control If the turn signal switch is operated when changing lanes to the passing lane at a vehicle speed of approximately 80 km/h (50 mph) during follow-up control, the vehicle will begin preliminary acceleration; once the vehicle has changed lanes it will first maintain this preliminary acceleration, and then slowly accelerate to the set vehicle speed. - ○ ○
Dynamic Radar Cruise Control with Road Sign Assist*1 This function is turned on and while RSA system speed limit information is displayed, the speed limit can be set by push down the +RES switch to increase the set vehicle speed to the speed limit, or by push down the -SET switch to reduce the set vehicle speed to the speed limit. - - ○
Curve Speed Reduction Control When the system determines that it is necessary to restrain the vehicle speed due to a curve, the system uses throttle control and brake control to perform speed restraint. - ○ ○
Set Control When the dynamic radar cruise control system has been turned on using the cruise control switch on the steering pad switch assembly, either of the relevant vehicle speed conditions shown below is met, and the -SET switch on the steering pad switch assembly is pressed, the hybrid vehicle control ECU assembly stores the vehicle speed and maintains the vehicle constantly at that speed. ○ ○ ○
The vehicle is being driven at a speed of approximately 30 km/h to 200 km/h (20 mph to 125 mph). ○ - -
The vehicle is being driven at a speed of approximately 30 km/h to 180 km/h (20 mph to 110 mph). - ○ ○
When the vehicle is traveling at a speed of approximately 30 km/h (20 mph) or less and a vehicle ahead is detected, the set vehicle speed is set to the low speed limit [approximately 30 km/h (20 mph)]. - - ○
Low Speed Limit Control The low speed limit is the lowest speed that cruise control can be set at and it is designed to be approximately 30 km/h (20 mph). The cruise control cannot be set below that speed. If the vehicle speed drops below that speed while driving using cruise control, the cruise control will be canceled automatically. The set vehicle speed is kept in memory. ○ - -
The low speed limit is the lowest speed that cruise control can be set at and it is designed to be approximately 25 km/h (16 mph). The cruise control cannot be set below that speed. If the vehicle speed drops below that speed while driving using cruise control, the cruise control will be canceled automatically. The set vehicle speed is kept in memory. - ○ -
COAST Control While the -SET switch on the steering pad switch assembly is pushed continuously, the vehicle speed and the set vehicle speed change as follows, according to the mode: ○ ○ ○
·

The vehicle decelerates constantly.

·

The set vehicle speed changes to the speed at which the -SET switch is released.


○ - -
·

The set vehicle speed decreases in increments of 5 km/h or 5 mph [Example: 103 →100 → 95 → 90 → 85 km/h (mph)].

·

The vehicle decelerates rapidly. The vehicle will remain at the speed that the vehicle is traveling at when the -SET switch is released.


- ○ ○
Tap Down Control When the -SET switch on the steering pad switch assembly is pushed momentarily (approximately 0.6 seconds or less), the vehicle speed and the set vehicle speed change as follows, according to the mode: ○ ○ ○
·

The vehicle will decelerate in increments of approximately 1 km/h or 1 mph each time the -SET switch is pushed.

·

However, if the difference between the actual vehicle speed and the set vehicle speed is greater than 5 km/h (3 mph), the set vehicle speed will change to the speed at which the vehicle was being driven at the time the -SET switch was operated.


○ - -
The vehicle will decelerate in increments of approximately 1 km/h or 1 mph for each time the -SET switch is pushed. - ○ ○
Accelerator Control While the +RES switch on the steering pad switch assembly is pushed continuously, the vehicle speed and the set vehicle speed change as follows, according to the mode: ○ ○ ○
·

The vehicle will accelerate constantly.

·

The set vehicle speed changes to the speed at which the +RES switch is released.


○ - -
·

The set vehicle speed increases in increments of 5 km/h or 5 mph [Example: 83 → 85 → 90 → 95 → 100 km/h (mph)].

·

The vehicle will accelerate to the speed that is set at the time the +RES switch is released. However, only the set vehicle speed will change during follow-up control.


- ○ ○
If the steering pad switch assembly is pressed momentarily (approximately 0.6 seconds or less) to the -SET switch when the vehicle speed is increased by pressing the accelerator pedal, the system will memorize the set vehicle speed at that speed. (If you press the -SET switch faster than the upper speed limit, the system will memorize the upper speed limit as the set speed.) ○ ○ ○
Resume Control If the vehicle speed is above the low speed limit, the +RES switch on the steering pad switch assembly can be pushed to resume cruise control operation and reach the vehicle speed that was set at the time the driver canceled cruise control. ○ ○ ○
Even if the vehicle speed drops below the low speed limit, resumption can be performed when the vehicle speed increases to above the low speed limit. However, resumption can be performed even if the vehicle speed is below the low speed limit when the vehicle is running in mode C and there is a vehicle ahead. - - ○
If the vehicle ahead changes driving lanes during follow-up control, the vehicle speed is gradually increased to the set vehicle speed. At this time, the vehicle speed can be increased promptly by pushing the +RES switch on the steering pad switch assembly. - ○ ○
After the vehicle ahead has started running again under stop retention control and then the message that urges the driver to perform the start-off operation has been displayed, when the steering pad switch assembly is pushed to the +RES switch, follow-up control is resumed and the vehicle can be accelerated up to the set speed. - - ○
Tap Up Control When the +RES switch on the steering pad switch assembly is pushed momentarily (approximately 0.6 seconds or less), the vehicle speed and the set vehicle speed change as follows: ○ ○ ○
·

The vehicle will accelerate in increments of approximately 1 km/h or 1 mph for each time the +RES switch was pushed.

·

However, if the difference between the actual vehicle speed and the set vehicle speed is greater than 5 km/h (3 mph), the set vehicle speed will not change.


○ - -
The vehicle will accelerate in increments of approximately 1 km/h or 1 mph for each time the +RES switch is pushed. - ○ ○
Manual Cancel Control If any of the following signals are sent to the hybrid vehicle control ECU assembly, the cruise control is canceled accordingly:
·

Stop light switch on signal (The brake pedal is depressed).

·

Shift lever is moved from D to any other position.

·

When 1st, 2nd or 3rd range is selected in D position by shift paddle switch (Transmission shift switch assembly).*2

·

CANCEL switch on signal (CANCEL switch on the steering pad switch assembly is pushed).

·

Cruise control switch off signal sent to the hybrid vehicle control ECU assembly.

·

Electric parking brake is applied. (Only during full-speed range following function vehicle-to-vehicle distance control mode)


○ ○ ○
Automatic Cancel Control When an automatic cancel signal is sent to the hybrid vehicle control ECU assembly, cruise control operation is canceled. At this time, the type of warning sent to the driver and the control resumption condition varies according to the cancel signal. ○ ○ ○
Mode Switching Control The following operations switch modes:
·

Vehicle-to-vehicle distance control mode is activated immediately after the switch is turned on. The mode is changed to constant speed control mode by pressing and holding the switch for more than 1.5 seconds while the dynamic radar cruise control system is turned off.


○ ○ ○
Other Cancel Conditions
·

VSC operates during cruise control driving.

·

TRC operates for a certain period of time while the cruise control.

·

TRC is off or VSC is off.

·

Pre-collision system operates during cruise control driving.

·

Ignition switch off.

·

Drive start control operates during cruise control driving. (Only during full-speed range following function vehicle-to-vehicle distance control mode)

·

Parking support brake system operates during cruise control driving. (Only during full-speed range following function vehicle-to-vehicle distance control mode)


○ ○ ○
Diagnosis If a malfunction occurs in the dynamic radar cruise control system during cruise control operation, the hybrid vehicle control ECU assembly cancels cruise control and memorizes information related to the malfunction. ○ ○ ○



b.

Constant Speed Control Mode

i.

The hybrid vehicle control ECU assembly compares the set vehicle speed and the actual vehicle speed, and performs constant speed control in order to attain the set vehicle speed.



c.

Vehicle-to-vehicle Distance Control Mode

·

In vehicle-to-vehicle distance control mode, the hybrid vehicle control ECU assembly performs constant speed control function, deceleration control function, follow-up control function, acceleration control function, stop control function*, stop retention control function*, start control function*, turn signal-linked control function or curve speed reduction control function based on the information about the vehicle ahead transmitted from the millimeter wave radar sensor assembly and forward recognition camera.

*: Models with full-speed range following function


i.

Constant Speed Control Function

·

The hybrid vehicle control ECU assembly compares the set vehicle speed and the actual vehicle speed, and performs constant speed control by regulating the throttle in order to attain the set vehicle speed. The forward recognition camera uses the millimeter wave radar sensor assembly signal and information from the forward recognition camera to determine the condition in front of the vehicle and sends acceleration/deceleration requests to the hybrid vehicle control ECU assembly.

Y270310E03
1.771,0.333 5.75,0.531 3.979,0.198 10 false Forward Recognition Camera 4.813,0.302 6.698,0.781 1.885,0.479 10 false Millimeter Wave Radar Sensor Assembly 0.708,2.406 1.854,2.615 1.146,0.208 10 false Own Vehicle 5.427,1.896 6.292,2.188 0.865,0.292 10 false MG ECU 5.396,2.198 6.375,2.448 0.979,0.25 10 false - MG2 Control 5.615,2.656 6.594,2.906 0.979,0.25 10 false ECM 5.125,2.885 6.635,3.125 1.51,0.24 10 false Throttle Control Motor 5.125,3.188 6.635,3.427 1.51,0.24 10 false - Throttle Valve Control 3,2.167 3.906,2.792 0.906,0.625 10 false Hybrid Vehicle Control ECU Assembly 5.042,1.458 6.594,1.698 1.552,0.24 10 false Acceleration Control



ii.

Deceleration Control Function

·

The forward recognition camera calculates the target deceleration rate in accordance with signals from the millimeter wave radar sensor assembly, forward recognition camera and transmits a deceleration request signal to the hybrid vehicle control ECU assembly. Upon receiving this signal, the hybrid vehicle control ECU assembly performs engine, MG2 and brake control in order to cause the vehicle to decelerate.

·

This control is not performed in the presence of a parked vehicle or object or below the settable vehicle speed range.

Y270311E01
0.75,1.385 1.875,1.677 1.125,0.292 10 false Vehicle Ahead 0.833,3.927 1.958,4.219 1.125,0.292 10 false Own Vehicle 4.813,0.26 6.708,0.75 1.896,0.49 10 false Millimeter Wave Radar Sensor Assembly 2.958,1.833 4.333,2.24 1.375,0.406 10 false Hybrid Vehicle Control ECU Assembly 5.146,1.146 6.427,1.365 1.281,0.219 10 false Acceleration Control 1.156,0.281 2.99,0.594 1.833,0.313 10 false Forward Recognition Camera 5.604,1.51 6.313,1.729 0.708,0.219 10 false MG ECU 5.427,1.813 6.708,2.031 1.281,0.219 10 false - MG2 Control 5.667,2.25 6.125,2.5 0.458,0.25 10 false ECM 5.219,2.854 6.635,3.083 1.417,0.229 10 false - Throttle Valve Control 5.115,3.438 6.458,3.74 1.344,0.302 10 false Deceleration Control 5.292,3.917 6.635,4.219 1.344,0.302 10 false Skid Control ECU 5.354,4.208 6.448,4.49 1.094,0.281 10 false - Brake Control 5.208,2.5 6.625,2.698 1.417,0.198 10 false Throttle Control Motor

·

If the forward recognition camera determines that further deceleration is necessary, it transmits a brake request signal to the hybrid vehicle control ECU assembly. Upon receiving this signal, the hybrid vehicle control ECU assembly transmits a brake request signal to the skid control ECU. The skid control ECU then controls the brake actuator to apply the brakes.

·

At this time, if the deceleration rate is higher than a predetermined value, the skid control ECU outputs a stop light illumination request signal to the stop lights in order to warn any vehicles behind.

Y270312E01
3.021,1.771 4.396,2.625 1.375,0.854 10 false Hybrid Vehicle Control ECU Assembly 1.115,0.281 3.094,0.604 1.979,0.323 10 false Forward Recognition Camera 4.792,0.26 6.667,0.75 1.875,0.49 10 false Millimeter Wave Radar Sensor Assembly 5.052,1.063 6.927,1.552 1.875,0.49 10 false Acceleration Control 5.573,1.458 6.646,1.875 1.073,0.417 10 false MG ECU 5.573,1.823 6.646,2.24 1.073,0.417 10 false - MG2 Control 5.74,2.219 6.813,2.635 1.073,0.417 10 false ECM 5.208,2.438 6.635,2.698 1.427,0.26 10 false Throttle Control Motor 5.313,2.813 6.74,3.073 1.427,0.26 10 false - Throttle Valve Control 5.177,3.406 6.573,3.667 1.396,0.26 10 false Deceleration Control 5.385,4.188 6.781,4.448 1.396,0.26 10 false - Brake Control 5.313,3.885 6.708,4.146 1.396,0.26 10 false Skid Control ECU 0.865,2.802 2.24,3.656 1.375,0.854 10 false Own Vehicle 0.729,3.958 2.104,4.813 1.375,0.854 10 false Vehicle Behind 0.802,1.49 2.177,2.344 1.375,0.854 10 false Vehicle Ahead

·

If the vehicle is not decelerating adequately, the hybrid vehicle control ECU assembly sounds a buzzer. The buzzer is sounded to urge the driver to depress the brake pedal.

Y270313E03
0.76,1.698 1.823,2.031 1.063,0.333 10 false Vehicle Ahead 0.813,3.292 1.875,3.625 1.063,0.333 10 false Own Vehicle 0.771,4.313 1.833,4.646 1.063,0.333 10 false Vehicle Behind 1.729,0.229 3.677,0.469 1.948,0.24 10 false Forward Recognition Camera 4.802,0.208 6.698,0.656 1.896,0.448 10 false Millimeter Wave Radar Sensor Assembly 5.552,0.938 6.448,1.177 0.896,0.24 10 false Warning 5.573,1.385 6.469,1.625 0.896,0.24 10 false Buzzer 5.156,2.042 6.698,2.281 1.542,0.24 10 false Acceleration Control 5.531,2.469 6.26,2.677 0.729,0.208 10 false MG ECU 5.74,3.219 6.25,3.49 0.51,0.271 10 false ECM 5.281,3.781 6.708,4 1.427,0.219 10 false - Throttle Valve Control 5.177,4.375 6.573,4.656 1.396,0.281 10 false Deceleration Control 5.26,4.833 6.427,5.115 1.167,0.281 10 false Skid Control ECU 5.354,5.177 6.396,5.406 1.042,0.229 10 false - Brake Control 2.885,2.969 4.271,3.427 1.385,0.458 10 false Hybrid Vehicle Control ECU Assembly 5.188,3.49 6.844,3.708 1.656,0.219 10 false Throttle Control Motor 5.417,2.792 6.469,2.979 1.052,0.188 10 false - MG2 Control



iii.

Follow-up Control Function

·

After performing deceleration control, the forward recognition camera transmits request signals to the hybrid vehicle control ECU assembly so that the vehicle can follow the vehicle ahead while maintaining the proper vehicle-to-vehicle distance according to the vehicle speed. Upon receiving these signals, these ECUs control the motive force in order to perform follow-up control.

·

3 stages (long, middle and short) of vehicle-to-vehicle distance can be selected by operating the vehicle-to-vehicle distance control switch.

Y270314E03
0.917,3.344 2.01,3.896 1.094,0.552 10 false Vehicle-to-vehicle Distance 0.781,2.656 1.906,2.885 1.125,0.229 10 false Vehicle Ahead 0.76,4.177 1.74,4.417 0.979,0.24 10 false Own Vehicle 1.573,0.802 3.469,1.063 1.896,0.26 10 false Forward Recognition Camera 4.844,0.813 6.75,1.208 1.906,0.396 10 false Millimeter Wave Radar Sensor Assembly 4.76,1.615 6.76,1.99 2,0.375 10 false Steering Pad Switch Assembly 4.927,2.156 6.594,2.688 1.667,0.531 10 false Vehicle-to-vehicle Distance Control Switch 5.125,3.031 6.688,3.302 1.563,0.271 10 false Acceleration Control 5.781,3.438 6.375,3.688 0.594,0.25 10 false MG ECU 5.677,3.76 6.635,4.021 0.958,0.26 10 false - MG2 Control 5.906,4.208 6.396,4.438 0.49,0.229 10 false ECM 5.438,4.781 6.896,5 1.458,0.219 10 false - Throttle Valve Control 5.208,5.302 6.708,5.479 1.5,0.177 10 false Deceleration Control 5.281,5.74 6.781,5.917 1.5,0.177 10 false Skid Control ECU 5.344,6.104 6.844,6.281 1.5,0.177 10 false - Brake Control 2.865,3.906 4.24,4.458 1.375,0.552 10 false Hybrid Vehicle Control ECU Assembly 5.365,4.479 6.823,4.656 1.458,0.177 10 false Throttle Control Motor



iv.

Acceleration Control Function

·

If the forward recognition camera detects (based on the millimeter wave radar sensor assembly and forward recognition camera) that either the vehicle ahead or the driver has changed lanes, an acceleration request signal is transmitted to the hybrid vehicle control ECU assembly in order to attain the set vehicle speed. Upon receiving this signal, the hybrid vehicle control ECU assembly controls the motive force of the engine and MG2 in order to perform acceleration control.

Y270315E01
2.135,0.25 3.458,0.781 1.323,0.531 10 false Forward Recognition Camera 4.729,0.25 6.625,0.74 1.896,0.49 10 false Millimeter Wave Radar Sensor Assembly 5.177,1.354 6.594,1.594 1.417,0.24 10 false Acceleration Control 5.51,1.781 6.271,1.99 0.76,0.208 10 false MG ECU 5.396,2.115 6.5,2.385 1.104,0.271 10 false - MG2 Control 2.813,2.229 4.208,2.823 1.396,0.594 10 false Hybrid Vehicle Control ECU Assembly 5.667,2.552 6.177,2.844 0.51,0.292 10 false ECM 5.25,3.125 6.844,3.375 1.594,0.25 10 false - Throttle Valve Control 1.24,1.438 2.219,1.698 0.979,0.26 10 false Vehicle Ahead 0.771,3.01 1.75,3.271 0.979,0.26 10 false Own Vehicle 5.135,2.823 6.729,3.073 1.594,0.25 10 false Throttle Control Motor



v.

Stop Control Function (Models with Full-speed Range Following Function)

·

During vehicle-to-vehicle distance control mode, if the vehicle ahead stops, the forward recognition camera maintains an appropriate vehicle-to-vehicle distance while at the same time calculating the necessary driving force to stop the vehicle, and sends a drive request signal to the hybrid vehicle control ECU assembly and skid control ECU. When the hybrid vehicle control ECU assembly and skid control ECU receive this signal, they control the driving force and stop the vehicle.

·

At this time, the skid control ECU outputs a stop light illumination request signal in order to inform anyone who might be following the vehicle.

·

The distance between the driver's own vehicle and the preceding vehicle when the vehicles are stopped is set to approximately 3 m to 5 m (10 ft. to 16 ft.) regardless of the vehicle-to-vehicle distance preset by using the vehicle-to-vehicle distance control switch.

Y270316E02
1.833,0.354 3.667,0.76 1.833,0.406 10 false Forward Recognition Camera 4.865,0.385 6.74,0.792 1.875,0.406 10 false Millimeter Wave Radar Sensor Assembly 3.021,2.427 4.396,2.948 1.375,0.521 10 false Hybrid Vehicle Control ECU Assembly 5.156,1.458 6.521,1.781 1.365,0.323 10 false Acceleration Control 5.615,1.958 6.354,2.208 0.74,0.25 10 false MG ECU 5.521,2.281 6.688,2.49 1.167,0.208 10 false - MG Control 5.771,2.719 6.188,2.917 0.417,0.198 10 false ECM 5.344,3.323 6.823,3.542 1.479,0.219 10 false - Throttle Valve Control 4.583,3.885 6.063,4.094 1.479,0.208 10 false Deceleration Control 3.823,4.448 5.01,4.677 1.188,0.229 10 false Skid Control ECU 5.844,4.792 6.854,5.031 1.01,0.24 10 false Stop Light On 0.896,4.26 2.083,4.49 1.188,0.229 10 false Vehicle Behind 0.896,1.833 2.083,2.063 1.188,0.229 10 false Vehicle Ahead 0.896,3.115 2.083,3.344 1.188,0.229 10 false Own Vehicle 5.271,3.01 6.75,3.229 1.479,0.219 10 false Throttle Control Motor 3.885,4.833 5.073,5.063 1.188,0.229 10 false - Brake Control



vi.

Stop Retention Control Function (Models with Full-speed Range Following Function)

·

After the vehicle has stopped under stop control, the hybrid vehicle control ECU assembly transmits a stop retention request signal to the skid control ECU. Upon receiving this signal, the skid control ECU activates the brake hold function and keeps the vehicle stopped.

HINT:

If the vehicle ahead starts off within approximately 3 seconds after own vehicle stops, follow-up cruising will be resumed.

Y270317E02
3.083,1.938 4.458,2.542 1.375,0.604 10 false Hybrid Vehicle Control ECU Assembly 1.552,0.427 3.49,0.729 1.938,0.302 10 false Forward Recognition Camera 4.292,0.438 6.844,0.885 2.552,0.448 10 false Millimeter Wave Radar Sensor Assembly 1.052,1.802 2.104,2.198 1.052,0.396 10 false Vehicle Ahead 0.99,3.281 2.042,3.677 1.052,0.396 10 false Own Vehicle 4.26,3.302 5.833,3.563 1.573,0.26 10 false Stop Retention Control 3.427,3.781 4.583,4.052 1.156,0.271 10 false Skid Control ECU 3.49,4.104 4.646,4.375 1.156,0.271 10 false - Brake Control 5.573,3.729 6.729,4 1.156,0.271 10 false Stop Holding 5.604,4.188 6.583,4.458 0.979,0.271 10 false Stop Light On




vii.

Start Control Function (Models with Full-speed Range Following Function)

·

When the forward recognition camera detects that the vehicle ahead starts moving again from the millimeter wave radar sensor assembly and forward recognition camera signal, it displays the messages on the multi-information display and headup display* to urge the driver to perform the start-off operation (to push the +RES switch or depress the accelerator pedal).

*: Models with headup display

·

Upon receiving the start-off operation signal generated by pushing the +RES switch on the steering pad switch assembly or by depressing the accelerator pedal, the forward recognition camera transmits a motive force request signal to the hybrid vehicle control ECU assembly. Upon receiving this signal, the hybrid vehicle control ECU assembly controls the motive force, starts the vehicle and resumes follow-up control.

HINT:

Pressing the +RES switch while the vehicle ahead stops will resume follow-up cruising if the vehicle ahead starts off within approximately 3 seconds after the switch is pressed.


Y270318E02
1.688,0.25 3.5,0.594 1.813,0.344 10 false Forward Recognition Camera 4.729,0.219 6.625,0.688 1.896,0.469 10 false Millimeter Wave Radar Sensor Assembly 3.219,1.25 7.115,1.688 3.896,0.438 10 false Start-off Operation Request Display on Multi-information Display and Headup Display* 3.823,2.167 6.635,2.573 2.813,0.406 10 false Steering Pad Switch Assembly (+RES Switch Signal) 3.5,1.781 5.771,1.969 2.271,0.188 10 false Accelerator Pedal Operation Signal 0.073,5.844 2.104,6.063 2.031,0.219 10 false *: Models with Headup Display 2.688,3.615 4.063,4 1.375,0.385 10 false Hybrid Vehicle Control ECU Assembly 5.323,3.552 6.354,3.76 1.031,0.208 10 false - MG2 Control 5.469,3.208 6.458,3.365 0.99,0.156 10 false MG ECU 5.031,2.802 6.563,3 1.531,0.198 10 false Acceleration Control 5.573,3.99 6.115,4.25 0.542,0.26 10 false ECM 5.146,4.573 6.646,4.771 1.5,0.198 10 false - Throttle Valve Control 4.333,5.063 6.052,5.313 1.719,0.25 10 false Stop Retention Control 3.385,5.667 5.104,5.917 1.719,0.25 10 false Skid Control ECU 3.448,6.104 4.688,6.354 1.24,0.25 10 false - Brake Control 5.865,5.604 6.719,5.844 0.854,0.24 10 false Stop Holding 5.854,6.115 6.833,6.344 0.979,0.229 10 false Stop Light Off 0.74,4.521 1.802,4.76 1.063,0.24 10 false Own Vehicle 0.75,2.625 1.813,2.865 1.063,0.24 10 false Vehicle Ahead 5.094,4.292 6.594,4.49 1.5,0.198 10 false Throttle Control Motor



viii.

Turn signal-linked Control Function

·

If the turn signal switch is operated when changing lanes to the passing lane at a vehicle speed of approximately 80 km/h (50 mph) during follow-up control, the vehicle will begin preliminary acceleration; once the vehicle has changed lanes it will first maintain this preliminary acceleration, and then slowly accelerate to the set vehicle speed.

Y270319E02
1.781,0.698 2.813,0.906 1.031,0.208 10 false Vehicle Ahead 4,0.719 5.031,0.927 1.031,0.208 10 false Vehicle Ahead 6.354,0.365 6.854,0.75 0.5,0.385 10 false Vehicle Ahead 1.75,2.875 2.781,3.083 1.031,0.208 10 false Own Vehicle 3.948,2.458 4.979,2.667 1.031,0.208 10 false Own Vehicle 4.729,2.083 5.521,2.333 0.792,0.25 10 false Own Vehicle 2.927,4.031 5.49,4.281 2.563,0.25 10 false Millimeter Wave Radar Sensor Assembly 3.583,4.948 4.885,5.198 1.302,0.25 10 false Turn Signal Switch 2.469,6.438 3.854,7.01 1.385,0.573 10 false Hybrid Vehicle Control ECU Assembly 4.635,5.604 6.031,5.875 1.396,0.271 10 false Acceleration Control 5.094,6.021 5.833,6.292 0.74,0.271 10 false MG ECU 4.938,6.313 5.854,6.573 0.917,0.26 10 false - MG2 Control 5.219,6.781 6.396,6.979 1.177,0.198 10 false ECM 4.667,7.083 6.458,7.271 1.792,0.188 10 false Throttle Control Motor 0.75,5.531 2.031,5.896 1.281,0.365 10 false Forward Recognition Camera 4.896,7.354 6.563,7.573 1.667,0.219 10 false - Throttle Valve Control



ix.

Dynamic Radar Cruise Control with Road Sign Assist (Models with Dynamic Radar Cruise Control with Road Sign Assist)

·

This function is turned on and while RSA system speed limit information is displayed, the speed limit can be set by push down the +RES switch to increase the set vehicle speed to the speed limit, or by push down the -SET switch to reduce the set vehicle speed to the speed limit.

Y230943E11
4.073,0.302 6.948,0.719 2.875,0.417 10 false Operation Request Display on Multi-information Display and Headup Display* 4.813,1.031 6.75,1.552 1.938,0.521 10 false Steering Pad Switch Assembly (+RES/-SET Switch Signal) 5.406,1.875 6.833,2.146 1.427,0.271 10 false Acceleration Control 3.688,2.344 4.635,2.906 0.948,0.563 10 false Hybrid Vehicle Control ECU Assembly 5.354,2.438 6.708,2.719 1.354,0.281 10 false Throttle Control Motor 5.458,2.76 6.927,3.021 1.469,0.26 10 false - Throttle Valve Control 1.792,2.604 3.094,3.052 1.302,0.448 10 false Forward Recognition Camera 0.135,3.438 2.604,3.688 2.469,0.25 10 false *: Models with Headup Display



x.

Curve Speed Reduction Control Function

·

When the system determines that it is necessary to restrain the vehicle speed according to information from the sensors while driving in vehicle-to-vehicle distance control mode, displays on the headup display* and multi-information display are used to inform the driver that the curve speed reduction control function is operating.

*: Models with Headup Display

·

When control performed by the curve speed reduction control function completes, the display turns off and the vehicle returns to the set speed of the radar cruise control system according to the conditions.

Y251787E02
1.729,3.135 2.146,2.031 2.146,2.031 2.438,2.031 true 2.479,1.927 4.365,2.458 1.885,0.531 10 false Starts decelerating based on information from sensors 0.24,3.51 3.5,3.771 3.26,0.26 10 false This illustration is only for explanatory purposes.



xi.

Automatic Cancel Control

·

If one of the conditions listed below occurs while the vehicle is being driven using cruise control, speed control by the cruise control system will be canceled. Then, the following warning items will appear for the driver.

Constant Speed Control Mode
Situation Warning
Multi-information Display
Y124297

Buzzer
If the conditions listed below occurs, the hybrid vehicle control ECU assembly clears the set vehicle speed and cancels the cruise control.
·

An open or short circuit in the stop light switch assembly.


Speed control by the cruise control system is disabled until the power switch is turned on (IG) again.
Cruise Control
Malfunction
Visit Your
Dealer
Illuminates Sounds
If the following condition occurs, the hybrid vehicle control ECU assembly clears the set vehicle speed and cancels the cruise control.
·

Malfunction in the hybrid control system.


Speed control by the cruise control system is disabled until the power switch is turned on (IG) again.
- Illuminates -
If any of the following conditions occur, the hybrid vehicle control ECU assembly cancels the cruise control.
·

Stop light switch assembly input signal is abnormal.

·

Cancel circuit malfunction.

·

Brake control system malfunction.

·

Communication malfunction between the skid control ECU and hybrid vehicle control ECU assembly.


Speed control by the cruise control system is disabled until the power switch is turned on (IG) again.
Cruise Control
Malfunction
Visit Your
Dealer
Illuminates Sounds
If the following condition occurs, the hybrid vehicle control ECU assembly cancels the cruise control while retaining the set vehicle speed in its memory.
·

The vehicle speed drops below the low speed limit [approximately 30 km/h (20 mph)].


- Does not illuminate -
If the following condition occurs, the hybrid vehicle control ECU assembly clears the set vehicle speed and cancels the cruise control.
·

The vehicle speed drops more than 16 km/h (10 mph) below the set vehicle speed.


- Does not illuminate -
If any of the following conditions occur, the hybrid vehicle control ECU assembly clears the set vehicle speed and cancels speed control by the cruise control system.
·

VSC operates during cruise control driving.

·

TRC operates for a certain period of time during cruise control driving.

·

TRC is off or VSC is off.

·

Drive start control operates during cruise control driving.

·

Pre-collision system operates during cruise control driving.


- Does not illuminate -

Vehicle-to-vehicle Distance Control Mode
Situation Warning
Multi-information Display
Y124297

Buzzer

*1: Models with full-speed range following function

*2: Models without full-speed range following function

If the conditions listed below occurs, the hybrid vehicle control ECU assembly clears the set vehicle speed and cancels the cruise control.
·

An open or short circuit in the stop light switch assembly.


Speed control by the cruise control system is disabled until the power switch is turned on (IG) again.
Cruise Control
Malfunction
Visit Your
Dealer
Illuminates Sounds
If the following condition occurs, the hybrid vehicle control ECU assembly clears the set vehicle speed and cancels the cruise control.
·

Malfunction in the hybrid control system.


Speed control by the cruise control system is disabled until the power switch is turned on (IG) again.
- Illuminates -
If one of the conditions listed below occurs, the hybrid vehicle control ECU assembly clears the set vehicle speed and cancels the cruise control.
·

Malfunction of the millimeter wave radar sensor assembly.

·

Misalignment of the axis of the millimeter wave radar sensor assembly.

·

Malfunction in the dynamic radar cruise control system other than those given above.

·

Stop light switch assembly input signal is abnormal.

·

Cancel circuit malfunction.

·

The brake holding control system is malfunction.*1


Speed control by the cruise control system is disabled until the power switch is turned on (IG) again.
Cruise Control
Malfunction
Visit Your
Dealer
Illuminates Sounds
If the following condition occurs, the hybrid vehicle control ECU assembly cancels the cruise control while retaining the set vehicle speed in its memory.
·

The millimeter wave radar sensor assembly or the radar sensor cover are dirty.


Speed control by the cruise control system is prohibited until the condition is corrected or the cruise control system is turned off and back on again using the cruise control switch on the steering pad switch assembly.
Radar Cruise
Control
Unavailable
See Owner's Manual
Illuminates Sounds
If any of the following conditions occur, the hybrid vehicle control ECU assembly cancels the cruise control while retaining the set vehicle speed in its memory.
·

The measurement becomes extremely unstable due to poor weather conditions.

·

Brake control by the dynamic radar cruise control system is temporarily unavailable.

·

Misalignment of the axis of the millimeter wave radar sensor assembly.

·

A Malfunction in the forward recognition camera.

·

Forward recognition camera temporarily not available.


Speed control by the cruise control system is prohibited until the condition is corrected or the cruise control system is turned off and back on again using the cruise control switch on the steering pad switch assembly.
Radar Cruise
Control
Unavailable
Illuminates Sounds
If the following condition occurs, the hybrid vehicle control ECU assembly cancels the cruise control while retaining the setting vehicle speed in its memory.*2
·

The vehicle speed drops below the low speed limit. [approximately 25 km/h (16 mph)].


- Does not illuminate Sounds
Twice
If any of the following conditions occur, the hybrid vehicle control ECU assembly cancels speed control by the cruise control system.*1
·

Stop light switch assembly input signal is abnormal.

·

Malfunction in the millimeter wave radar sensor assembly.

·

Beam axis of millimeter wave radar sensor assembly misaligned.

·

The electric parking brake system is malfunctioning.

·

An open or short circuit in the stop light switch assembly.

·

Problem with cruise control switch cancel circuit.

·

The millimeter wave radar sensor assembly or the radar sensor cover are dirty.

·

Brake control by the dynamic radar cruise control system is temporarily unavailable.

·

The forward recognition camera is temporarily unavailable.


Cruise Control Fault
Press Brake to
Deactivate
Visit Your Dealer
Illuminates Sounds
If any of the following conditions occur while the vehicle stopped, the hybrid vehicle control ECU assembly cancels control of vehicle speed by the dynamic radar cruise control system.*1
·

The driver door is opened.

·

The vehicle is parked for a long period of time.

·

The vehicle is driving on as steep hill.

·

A preceding vehicle is not detected.

·

The driver seat belt is unfastened.


Radar Cruise Control Unavailable Press Brake to Resume Driving Does not illuminate -
If any of the following conditions occur, the hybrid vehicle control ECU assembly clears the set vehicle speed and cancels speed control by the cruise control system.
·

VSC operates during cruise control driving.

·

TRC operates for a certain period of time during cruise control driving.

·

TRC is off or VSC is off.

·

Drive start control operates during cruise control driving.

·

Electric parking brake operates.*1

·

Parking support brake system operates during cruise control driving.*1

·

Pre-collision system operates during cruise control driving.


- Does not illuminate -





DIAGNOSIS


a.

In order to make system inspections easier to perform, a diagnosis function is used in consideration of serviceability. The DTCs of malfunctioning parts can be read by connecting the Global TechStream (GTS). For details, refer to the Repair Manual.