OUTLINE
The combination meter assembly has a built-in meter ECU and buzzer.
A multi-information display on which various kinds of information is displayed is integrated.
| *a | Multi-information Display | *b | The illustrations are examples that shows the locations of the indicators. |
| *A | Type A | *B | Type B |
| *C | Type C | - | - |
| *a | Multi-information Display | *b | The illustrations are examples that shows the locations of the indicators. |
Headup Display
A headup display has been adopted to enable the driver to see driving information more easily within their field of view.
The meter mirror sub-assembly and the structure of the windshield glass enables the headup display to project an image as if it is displayed outside of the windshield glass.
| *a | Projected Image from the Headup Display | *b | The illustrations shown are examples only. |
| *a | Projected Image from the Headup Display | *b | The illustrations shown are examples only. |
MAIN FEATURES
Combination Meter Assembly (Models with 4.2 Inch Multi-information Display)
Opening/Ending Ceremony
An opening ceremony which allows for anticipation of a pleasant drive is used. The opening ceremony operates as follows:
The following illustration shows the flow of the opening and ending ceremony from when the power switch is off and then the engine is started, to when the power switch is turned off again.
| *a | IG ON | *b | IG OFF |
| *c | The illustrations shown are examples only. | - | - |
When the power switch is turned on (IG), the multi-information display illuminates.
Then, the needles, gauges and panels of the speedometer, hybrid system indicator, engine coolant temperature gauge and fuel gauge illuminates.
When the power switch is turned off, only the odometer and clock* are displayed on the multi-information display.
The needles, gauges and panels of the speedometer, hybrid system indicator, engine coolant temperature gauge and fuel gauge fade out.
Then, the odometer and clock* fade out.
*: Models with clock (Combination meter assembly)
Multi-information Display
The multi-information display is located at the center of the combination meter assembly.
The multi-information display shows the following information.
| Item | Outline |
|---|---|
|
*1: Except models with Toyota Safety Sense *2: Models with Toyota Safety Sense *3: Models with audio system *4: Models with voice recognition system *5: Models with clock (combination meter assembly) *6: Models with drive mode select switch *7: Models with blind spot monitor system *8: Models with TOYOTA parking assist-sensor system *9: Models with rear camera detection system |
|
| Shift Position Indicator | The current shift position is displayed. |
| Outside Temperature | ·
The outside temperature is displayed. ·
When the outside temperature drops below 3°C (37°F), an ice warning to warn the driver to drive with caution due to possibly icy road conditions. After the ice warning flashes 10 times, the ice warning stay on. When the temperature reaches 5°C (41°F), the ice warning goes off. |
| Indicator | ·
When the display conditions are met, the following indicators illuminate. -
Eco Mode Indicator*6 -
Sport Mode Indicator*6 -
Cruise Control Indicator*1 -
Cruise Control Indicator (Constant Speed Control Mode)*2 -
Cruise Control Indicator (Vehicle-to-Vehicle Distance Control Mode)*2 -
Cruise SET Indicator -
ECO Indicator -
Lane Tracing Assist Indicator*2 -
EV Drive Indicator -
AGC (Auto Glide Control) Indicator -
Blind Spot Monitor Indicator*7 -
Clearance Sonar OFF Indicator*8 -
RCD OFF Indicator*9 |
| Drive Mode | ·
The currently selected drive mode is displayed. -
ECO Mode -
SPORT Mode -
EV Mode |
| Dynamic Radar Cruise Control System/Lane Tracing Assist System State*2 | Displays the operating state of the dynamic radar cruise control system and lane tracing assist system. |
| Information | ·
The following information can be displayed on the multi-information display by switching the tabs. -
Drive Information Tab -
Audio Information Tab*3 -
Driving Assist System Information Tab*2 -
Warning Message Tab -
Settings Tab
|
| Interrupt Display | ·
When the display conditions are met, the following screen is interrupt display. -
Advisory Display/Warning Display -
Driving Assist System Information*2 -
Incoming Telephone Display*3 -
Audio Information Display*3 -
Voice Recognition Display*4 -
Rheostat |
| Vehicle Power Source State | ·
The vehicle power source state is displayed. ·
The following indicator is displayed on the multi-information display. -
Smart Indicator |
| ODO/TRIP Meter | ·
The odometer, trip meter A or trip meter B are displayed. ·
The item shown can be switched by pressing the ODO/TRIP switch. |
| Clock*5 | The current time is displayed. |
| Light Control Rheostat | Meter panel luminance can be changed by using the rheostat switch. |
The drive information shows the following information.
| Item | Outline |
|---|---|
| Drive Information | ·
The following items can be displayed. -
Trip (After Start) (1)
Average Fuel Consumption After Engine Start-up (2)
Average Vehicle Speed After Engine Start-up (3)
Elapsed Time After Engine Start-up -
Total (After Reset) (1)
Current Fuel Consumption (Bar Display) (2)
Average Fuel Consumption Between Reset Operations (3)
Total Average Vehicle Speed Between Reset Operations -
Tank (After Refuel) (1)
Cruising Range (2)
Average Fuel Consumption After Refueling ·
In addition to the above functions, the following items can be displayed. -
Energy Monitor -
Vehicle speed -
Blank
|
Combination Meter Assembly (Models with 7 Inch Multi-information Display)
Opening/Ending Ceremony
| *a | IG ON | *b | IG OFF |
| *c | The illustrations shown are examples only. | - | - |
When the power switch is turned on (IG), the needles, gauges and panels of the speedometer, hybrid system indicator, engine coolant temperature gauge and fuel gauge illuminates.
The multi-information display illuminates.
When the power switch is turned off, only the odometer and clock* are displayed on the multi-information display.
The needles, gauges and panels of the speedometer, hybrid system indicator, engine coolant temperature gauge and fuel gauge fade out.
Then, the odometer and clock* fade out.
*: Models with clock (Combination meter assembly)
Multi-information Display
The multi-information display is located at the center of the combination meter assembly.
The multi-information display shows the following information.
| Item | Outline |
|---|---|
|
*1: Models with blind spot monitor system *2: Models with TOYOTA parking assist-sensor system *3: Models with Toyota Safety Sense *4: Models with cruise control system *5: Models with front fog light *6: Models with rear fog light *7: Models with navigation system *8: Models with audio system *9: Models with voice recognition system *10: Models with clock (combination meter assembly) *11: Models with rear camera detection system |
|
| Indicator | ·
When the display conditions are met, the following indicators illuminate. -
Blind Spot Monitor Indicator*1 -
RCTA (Rear Crossing Traffic Alert) Indicator*1 -
Clearance Sonar Indicator*2 -
Lane Tracing Assist Indicator*3 -
Cruise SET Indicator*3, *4 -
Cruise Control Indicator*4 -
Cruise Control Indicator (Constant Speed Control Mode)*3 -
Cruise Control Indicator (Vehicle-to-Vehicle Distance Control Mode)*3 -
Automatic High Beam Indicator*3 -
Front Fog Light Indicator*5 -
Rear Fog Light Indicator*6 -
EV Drive Indicator -
AGC (Auto Glide Control) Indicator -
RCD OFF Indicator*11 |
| Drive Mode | ·
The currently selected drive mode is displayed. -
ECO Mode -
SPORT Mode -
EV Mode |
| Dynamic Radar Cruise Control System/Lane Tracing Assist System State | Displays the operating state of the dynamic radar cruise control system and lane tracing assist system. |
| Information | ·
The following information can be displayed on the multi-information display by switching the tabs. -
Warning Message Tab -
Fuel Economy Tab -
Driving Assist System Information Tab*3, *7 -
Audio Information Tab*8 -
Vehicle Information Tab -
Settings Tab
|
| Outside Temperature | ·
The outside temperature is displayed. ·
When the outside temperature drops below 3°C (37°F), an ice warning to warn the driver to drive with caution due to possibly icy road conditions. After the ice warning flashes 10 times, the ice warning stay on. When the temperature reaches 5°C (41°F), the ice warning goes off. |
| Shift Position Indicator | The current shift position is displayed. |
| ODO/TRIP Meter | ·
The odometer, trip meter A or trip meter B are displayed. ·
The item shown can be switched by pressing the ODO/TRIP switch. |
| Interrupt Display | ·
When the display conditions are met, the following screen is interrupt display. -
Advisory Display/Warning Display -
Driving Assist System Information*3, *7 -
Incoming Telephone Display*8 -
Audio Information Display*8 -
Voice Recognition Display*9 -
Rheostat |
| Vehicle Power Source State | ·
The vehicle power source state is displayed. ·
The following indicator is displayed on the multi-information display. -
Smart Indicator |
| Clock*10 | The current time is displayed. |
| Light Control Rheostat | Meter panel luminance can be changed by using the rheostat switch. |
The fuel economy tab shows the following information
| Fuel Economy Information | ·
The following items can be displayed. -
Current Fuel Consumption -
Average Fuel Economy (After Start) -
Driving Range -
Gadget
(1)
No Display (2)
Average Speed (After Start) (3)
Average Speed (After Reset) (4)
Distance Travelled (After Start) (5)
Distance Travelled (After Reset) (6)
Elapsed Time (After Start) (7)
Elapsed Time (After Reset) -
Average Fuel Economy
(1)
After Reset (2)
After Refuel |
| Eco Guide | ·
The following items can be displayed. -
ECO Acceleration Guidance -
ECO Judg -
Digital speed -
Auto Glide Control |
| Digital Speed | ·
The following items can be displayed. -
Digital speed -
Driving Range |
| EV Ratio | ·
The following items can be displayed. -
EV Ratio -
Drive Time -
Digital speed |
The driving assist system information tab shows the following information
|
*1: Models with navigation system *2: Models with Toyota Safety Sense |
|
| Navigation System Information*1 | ·
The following items can be displayed. -
Compass -
Turn-by-turn |
| Dynamic Radar Cruise Control System Information*2 | Dynamic radar cruise control system operation information is displayed. |
| Lane Tracing Assist System Information*2 | lane tracing assist system operation information is displayed. |
The audio information tab shows the following information
|
*: Models with audio system |
|
| Audio Information* | The audio source or an audio track can be selected.
|
The vehicle information tab shows the following information
|
*1: Models with tire inflation pressure display function *2: Models with Toyota Safety Sense *3: Models with TOYOTA parking assist-sensor system *4: Models with blind spot monitor system |
|
| Energy Monitor | The energy monitor is displayed. |
| Tire Pressure Status*1 | ·
Receives and displays the tire pressure of each tire. ·
Tire pressure is displayed as blank when the tire pressure signal cannot be received. ·
The tire pressure value is highlighted to warn the driver if the tire pressure drops below the threshold. |
| System Status | ·
The following systems can be set to on/off: -
Pre-collision System*2 -
Clearance Sonar System*3 -
Blind Spot Monitor System*4 -
Rear Crossing Traffic Alert*4
|
The tire pressure status or system status can be selected by pressing the left/right switch of the steering pad switch assembly.
Eco Guide
The fuel economy tab displays the ECO accelerator guidance and ECO driving score.
| *a | ECO Accelerator Guidance | *b | Eco Score |
| *c | The illustrations shown are examples only. | - | - |
The ECO acceleration guidance displays a bar graph to indicate ideal acceleration for Eco-friendly manner.
| *a | Eco Area | *b | Power Area |
| *c | Eco Driving Ratio Based on Acceleration | *d | Zone of Eco Acceleration |
| *e | The illustrations shown are examples only. | - | - |
The ECO accelerator guidance for ideal acceleration displays different values for each driving condition.
The ECO score displays the score of driving conditions (start, cruise and stop) rated out of 5.
Keeping the ECO accelerator guidance within the ECO acceleration zone when driving the vehicle will result in a high start and cruise ECO driving score.
Releasing the accelerator pedal earlier than usual before depressing the brake pedal will result in a high stop ECO driving score.
The total ECO driving score is rated out of 100 points.
When the power switch is on (READY), an ECO driving score is provided for each individual cycle which spans from start to stop.
When the power switch is turned off, the total ECO driving score from power switch on (READY) to power switch off is displayed.
| *a | Start | *b | Cruise |
| *c | Stop | *d | Score |
| *e | The illustrations shown are examples only. | - | - |
| Start | Bar graph to display ECO driving score when accelerating from stopped. |
| Cruise | Bar graph to display ECO driving score when cruising. |
| Stop | Bar graph to display ECO driving score when decelerating to stopped. |
| Score | Total ECO driving score based on ECO accelerator guidance. |
Hybrid System Indicator
The hybrid system indicator displays the total of the HV battery and engine output as the hybrid system output.
The scale for the hybrid system indicator is divided into 3 areas (Charge, Eco, Power). The role of each area is as follows.
| *a | Charge Area | *b | Hybrid Eco Area |
| *c | Eco Area | *d | Power Area |
| *e | The illustrations shown are examples only. | - | - |
| Area | Function |
|---|---|
| Charge | The Charge area indicates when energy is being regenerated. |
| Eco | ·
The Eco area indicates when the vehicle is being driven in an Eco-friendly manner. ·
The Hybrid Eco area indicates that the vehicle is driven in a manner that promotes frequent motor only operation. (Based on various conditions, the hybrid vehicle control ECU assembly controls if the engine should be stopped to enhance fuel efficiency.) |
| Hybrid Eco | |
| Power | The Power area indicates that the eco-friendly driving range is being exceeded (during full power driving, etc.). |
Headup Display
The headup display shows the following information:
The illustrations shown are examples only.
The illustrations shown are examples only.
| Area | Displayed Item |
|---|---|
|
*1: Models with Toyota Safety Sense *2: Models with TOYOTA parking assist-sensor system *3: Models with navigation system *4: Models with audio system *5: Models with Road Sign Assist System |
|
| Full screen | Pre-collision System Display*1 |
| a | TOYOTA Parking Assist-sensor System Display*2 |
| b | ·
The following items can be displayed. -
Dynamic Radar Cruise Control System Display*1 -
Lane Tracing Assist System Display*1 -
TOYOTA parking assist-sensor system detection display*2 -
Navigation System Display*3 -
Compass*3 -
Road Sign Assist System Display*5 |
| c | ·
The following items can be displayed. -
Hands off steering wheel alert display*1 -
Unsteady driving alert display*1 -
Master Warning -
Outside temperature/icy street warning display -
Information -
Telephone*4 -
Audio system operation status display*4 -
Tachometer |
| d | Speedometer |
| e | Shift Position Indicator |