OPERATION
Warning Indication
The combination meter assembly uses the multi-information display, PCS warning light, VSC OFF indicator light and buzzer to provide the driver with pre-collision system malfunction and indications.
| *1 | Combination Meter Assembly | - | - |
| *a | VSC OFF Indicator Light | *b | PCS Warning Light |
| *c | Multi-information Display | *d | LTA Indicator Light |
| *e | Master Warning Light | - | - |
| *1 | Combination Meter Assembly | - | - |
| *a | VSC OFF Indicator Light | *b | PCS Warning Light |
| *c | Multi-information Display | *d | LTA Indicator Light |
| *e | Master Warning Light | - | - |
Pre-collision System Operation Status Display
If the forward recognition camera determines that the possibility of a collision is high, it sends a signal to the combination meter assembly and meter mirror sub-assembly*. Upon receiving this signal, the combination meter assembly and meter mirror sub-assembly* indicates a warning using the multi-information display, headup display* and buzzer. Details are indicated below.
| Multi-information Display/Headup Display* | Buzzer |
|---|---|
|
*: Models with headup display |
|
| BRAKE! | Sounds Continuously |
For region A: When emergency steering assist operates, the LTA indicator in the combination meter assembly illuminates (green).
Indicator Display when Pre-collision System Off
When the pre-collision system is turned off in the settings menu of the multi-information display, the PCS warning light in the combination meter assembly illuminates and a message is displayed on the multi-information display.
| Multi-information Display | PCS Warning Light |
|---|---|
| Pre-Collision System OFF | Illuminates |
When pre-collision brake assist, pre-collision braking and emergency steering assist* operation are turned off using the VSC OFF switch, the VSC OFF indicator light and PCS warning light in the combination meter assembly illuminate, and a message is displayed on the multi-information display.
| Multi-information Display | VSC OFF Indicator Light | PCS Warning Light |
|---|---|---|
|
*: For region A |
||
| VSC Turned OFF Pre-Collision Brake System Unavailable | Illuminates | Illuminates |
Pre-collision System Warning Display
When the system is not available, the following warning occurs to warn the driver.
| Multi-information Display | Detail | Master Warning Light | PCS Warning Light | Buzzer |
|---|---|---|---|---|
| Pre-Collision System Malfunction Visit Your Dealer | This message appears when the forward recognition camera detects a system malfunction | Illuminates | Illuminates | Sounds once |
| Pre-Collision System Unavailable See Owner's Manual | Millimeter wave radar sensor assembly low voltage malfunction | - | Illuminates | - |
| Pre-Collision System Out of Temperature Range Unavailable See Owner's Manual | Millimeter wave radar sensor assembly temperature malfunction | - | Illuminates | - |
| Pre-Collision System Radar Sensor Blocked Unavailable Clean Radar Sensor | Dirty center mark of upper radiator grille or millimeter wave radar sensor assembly | - | Illuminates | - |
| Pre-Collision System Radar In Self Calibration Unavailable See Owner's Manual | Millimeter wave radar sensor assembly misaligned | - | Illuminates | - |
| Front Camera Unavailable See Owner's Manual | ·
Abnormal forward recognition camera voltage ·
Other forward recognition camera malfunction |
- | Illuminates | - |
| Front Camera Out of Temperature Range Unavailable Wait until Normal Temperature | Forward recognition camera temperature outside of operational range | - | Illuminates | - |
| Front Camera Low Visibility Unavailable See Owner's Manual | Dirty or fogged windshield glass over the forward recognition camera | - | Illuminates | - |
Changing settings of the pre-collision system
Enabling/disabling the pre-collision system
The pre-collision system can be enabled/disabled on setting display screen of the multi-information display.
The system is automatically enabled each time the power switch is turned to ON mode.
If the system is disabled, the PCS warning light will turn on and a message will be displayed on the multi-information display.
| *a | Steering Pad Switch Assembly | *b | PCS warning Light |
| *c | Multi-information Display | *d | The illustrations shown are examples only. |
Changing the pre-collision warning timing
The pre-collision warning timing can be changed on setting display screen of the multi-information display.
The warning timing setting is retained when the power switch is turned off. However, if the pre-collision system is disabled and re-enabled, the operation timing will return to the default setting (middle).
For region A: If the pre-collision warning timing is changed, emergency steering assist timing will also be changed accordingly. If late is selected, emergency steering assist would not operate in case of an emergency.
| *a | Steering Pad Switch Assembly | *b | Early |
| *c | Middle (This is the default setting.) | *d | Late |
| *e | The illustrations shown are examples only. | - | - |