Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PARKING SUPPORT BRAKE SYSTEM › from 2021.02
NM33C0E _56 Audio / Visual / Telematics _067379 PARK ASSIST / MONITORING _0473433 PARKING SUPPORT BRAKE SYSTEM CO CONTROL F

PARK ASSIST / MONITORING  PARKING SUPPORT BRAKE SYSTEM  CONTROL  PARKING SUPPORT BRAKE CONTROL  


FUNCTION OF MAIN COMPONENTS


Component Function

*1: Models with panoramic view monitor system

*2: Models with headup display

*3: Models with RCTA function

Front Corner Ultrasonic Sensor RH/LH Sends ultrasonic waves to detect stationary objects and outputs a signal to the clearance warning ECU assembly.
Front Center Ultrasonic Sensor RH/LH
Rear Corner Ultrasonic Sensor RH/LH
Rear Center Ultrasonic Sensor RH/LH
Blind Spot Monitor Sensor RH/LH*3 Sends a vehicle behind approaching detection signal to the clearance warning ECU assembly.
Clearance Warning ECU Assembly
·

Receives information regarding to a stationary object, etc. in the vehicle traveling direction detected by the ultrasonic sensor and a vehicle approaching the driver's own vehicle from behind detected by the blind spot monitor sensor*3, and judges the vehicle condition based on signals from sensors, switches and ECUs located various places to perform parking support brake system control.

·

Sends a parking support brake system control signal to the hybrid vehicle control ECU assembly and skid control ECU.

·

Sends a parking support brake system control status signal, warning request signal and malfunction judgment signal to the combination meter assembly.

·

Sends a parking support brake system warning request signal to the television camera controller.*1

·

Sends a parking support brake system warning request signal to the headup display.*2


Combination Meter Assembly
·

PKSB OFF Indicator

·

Multi-information Display

·

Master Warning Light


·

Sends a parking support brake system on/off signal to the clearance warning ECU assembly.

·

Receives a control status signal, warning request signal and combination meter assembly malfunction judgment signal from the clearance warning ECU assembly and displays a message on the multi-information display.

·

Illuminates the PKSB OFF indicator when the parking support system is off.

·

Sends a vehicle speed signal to the clearance warning ECU assembly.

·

Sends a customization signal to the clearance warning ECU assembly.

·

When a malfunction occurs, the master warning light blinks, the PKSB OFF indicator illuminates, the meter buzzer sounds, and warnings are displayed on the multi-information display, in order to inform the driver of a system malfunction.


Steering Pad Switch Assembly Sends operation signals from switches to the spiral cable sub-assembly.
Spiral Cable Sub-assembly Sends operation signals from the spiral cable sub-assembly to the combination meter assembly.
Radio and Display Receiver Assembly Receives a warning request signal from the television camera controller and displays a parking support brake system warning message.*1
Headup Display (Meter Mirror Sub-assembly)*2 Receives a warning request signal from the clearance warning ECU assembly and displays a parking support brake system warning message.
Hybrid Vehicle Control ECU Assembly
·

Sends a shift position signal, accelerator pedal depression amount signal, etc. to the clearance warning ECU assembly.

·

Performs drive force suppression control in response to a parking support brake system control signal received from the clearance warning ECU assembly.


Brake Booster with Master Cylinder Assembly
·

Skid Control ECU


·

Sends wheel speed information, a brake pedal status signal and a master cylinder pressure signal to the clearance warning ECU assembly.

·

Performs brake control in response to a parking support brake system control signal received from the clearance warning ECU assembly.

·

Sends a vehicle speed signal to the clearance warning ECU assembly.

·

Receives the lateral acceleration signal from the airbag sensor assembly, and sends the signal to the clearance warning ECU assembly.


Television Camera Controller*1 Sends a warning request signal received from the clearance warning ECU assembly to the radio and display receiver assembly.
Airbag Sensor Assembly
·

Yawrate Sensor


Sends a lateral acceleration signal, which was detected by the yawrate sensor, to the clearance warning ECU assembly.
Steering Sensor Sends a steering angle signal to the clearance warning ECU assembly.
Air Conditioning Amplifier Assembly Sends an outside temperature signal to the clearance warning ECU assembly.
Main Body ECU (Multiplex Network Body ECU) Sends model destination signal (information to indicate the market the vehicle was built for) to the clearance warning ECU assembly.


OPERATING CONDITION


a.

Drive Force Suppression Control

i.

When all of the following conditions are met, drive force suppression control is performed.

Detectable Item Condition

*: Models with RCTA function

Stationary Object
·

The ignition switch is ON.

·

The parking support brake system is on.

·

A stationary object is in the traveling direction of the driver's own vehicle.

·

The vehicle speed is 15 km/h (9 mph) or less.

·

The driver can avoid the object by braking operations.


Vehicle Approaching from Rear*
·

The ignition switch is ON.

·

The parking support brake system is on.

·

The shift position is R.

·

The vehicle speed of an approaching vehicle is 8 km/h (5 mph) or more.

·

The vehicle speed is 15 km/h (9 mph) or less.

·

An approaching vehicle may collide with the driver's own vehicle.




ii.

When any of the following conditions is met, drive force suppression control is stopped.

Detectable Item Condition

*: Models with RCTA function

Stationary Object
·

The ignition switch is ON.

·

The parking support brake system is off.

·

Collision is avoided.

·

A stationary object moves or is moved away from the traveling direction of the driver's own vehicle.


Vehicle Approaching from Rear*
·

The ignition switch is ON.

·

The parking support brake system is off.

·

Collision is avoided.

·

A vehicle, which was approaching the driver's vehicle from behind, has moved away.





b.

Brake Control

i.

When all of the following conditions are met, brake control is performed.

Detectable Item Condition
All Objects
·

Drive force suppression control is in operation.

·

Collision is difficult to avoid by braking by the driver.




ii.

When any of the following conditions are met, brake control is stopped.

Detectable Item Condition

*: Models with RCTA function

Stationary Object
·

The ignition switch is ON.

·

The parking support brake system is off.

·

A stationary object moves or is moved away from the traveling direction of the driver's own vehicle.

·

The driver depresses the brake pedal after the vehicle is stopped by brake control.

·

Approximately 2 seconds have elapsed since the vehicle is stopped by brake control.


Vehicle Approaching from Rear*
·

The ignition switch is ON.

·

The parking support brake system is off.

·

A vehicle, which was approaching the driver's vehicle from behind, has moved away.

·

The driver depresses the brake pedal after the vehicle is stopped by brake control.

·

Approximately 2 seconds have elapsed since the vehicle is stopped by brake control.



NOTICE:

When brake control operates, the parking support brake system automatically turns off. The system remains off until it is turned on by an operation on the multi-information display screen, the object of brake control goes away, the vehicle reverses approximately 300 mm (11.8 in.) or more*1 or approximately the entire length of the vehicle*2, the vehicle moves forward approximately the entire length of the vehicle*2, a shift operation is performed, or the ignition switch is turned off and back on.

*1: A vehicle approaching from the rear is detected.

*2: A stationary object is detected.






SYSTEM CONTROL


a.

Parking Support Brake (Stationary Objects) Detection Range

i.

The ultrasonic sensor detects stationary objects that come within approximately 4 m (13 ft.). In addition, the detection distance may differ depending on the shape of the stationary object.


ii.

When the vehicle is moving forward, all 4 front ultrasonic sensors must simultaneously detect an obstacle for the parking support brake system to operate. Similarly, when the vehicle is moving in reverse, 2 or more rear ultrasonic sensors must detect a stationary object for the system to operate.

Y221900C01
3.906,1.958 4.219,2.115 0.313,0.156 10 false *a 3.146,3.646 3.458,3.802 0.313,0.156 10 false *b 5.125,3.333 5.438,3.49 0.313,0.156 10 false *c 0.531,1.469 0.844,1.625 0.313,0.156 10 false *d 0.24,4.656 0.552,4.813 0.313,0.156 10 false *e 6.375,3.146 6.688,3.302 0.313,0.156 10 false *d 1.813,1.615 2.125,1.771 0.313,0.156 10 false *c
*a While Driving Ahead *b While Reversing
*c Approximately 4 m (13 ft.) *d Object
*e The detection range shown in the illustration is for when detecting an object that is 2 m (6.6 ft.) wide, 1 m (3.3 ft.) tall and is perpendicular to the ground. - -


NOTICE:

Even though the parking support brake system detects stationary objects, it may not operate depending on the vehicle condition.




b.

Parking Support Brake System Control

i.

The parking support brake system determines the state of the vehicle and its surroundings based on signals that the clearance warning ECU assembly receives from sensors, switches and ECUs installed in various locations on the vehicle, and sends the necessary control signals to ECUs to control the vehicle.

Y190224E04
0.729,0.042 2.927,0.344 2.198,0.302 10 false Drive Force Suppression Control 4.927,0.063 5.979,0.438 1.052,0.375 10 false Brake Control 0.438,0.469 3.198,1.104 2.76,0.635 10 false Drive force is suppressed when the operation conditions are met. 3.958,0.469 6.802,1.146 2.844,0.677 10 false Brake control is performed when the operation conditions are met. 1.281,1.573 2.646,1.917 1.365,0.344 10 false Collision is Possible 4.427,1.583 6.604,1.938 2.177,0.354 10 false Possibility of Collision is Very High 0.083,2.406 0.813,2.708 0.729,0.302 10 false Drive Force 1.01,3.188 1.885,3.563 0.875,0.375 10 false Start Control 4.542,3.188 5.417,3.563 0.875,0.375 10 false Start Control 3.927,2.313 4.406,2.677 0.479,0.365 10 false Braking Force 2.26,2.646 2.896,2.938 0.635,0.292 10 false DOWN 5.875,2.74 6.51,3.031 0.635,0.292 10 false UP 3.073,3.073 3.479,3.365 0.406,0.292 10 false Time 6.625,3.083 7.031,3.375 0.406,0.292 10 false Time


ii.

When the system operates, a warning message is displayed in the multi-information display of the combination meter assembly, headup display (meter mirror sub-assembly)*1 or radio and display receiver assembly*2, and the meter buzzer sounds to warn the driver.

*1: Models with headup display

*2: Models with panoramic view monitor system



iii.

The parking support brake system detects stationary objects using sensors, and when it determines that there is a risk of collision, suppress the drive force.

Drive Force Suppression Control
Y272264E01
0.938,0.521 2.135,0.823 1.198,0.302 10 false Vehicle Condition 0.125,2.656 0.917,3.719 0.792,1.063 10 false Combination Meter Assembly 1.115,2.146 2.698,2.448 1.583,0.302 10 false Multi-information Display 1.188,2.729 2.594,2.917 1.406,0.188 10 false PKSB OFF Indicator 1.417,3.25 2.396,3.531 0.979,0.281 10 false Meter Buzzer 0.156,4.229 2.813,4.563 2.656,0.333 10 false Radio and Display Receiver Assembly*2 0.906,4.854 2.365,5.115 1.458,0.26 10 false Headup Display*1 3.094,1.146 4.708,1.74 1.615,0.594 10 false Risk of collision and brake pedal is not depressed 5.125,1.146 6.979,1.531 1.854,0.385 10 false Due to drive force suppression control, vehicle cannot move 3.563,2.188 4.302,2.396 0.74,0.208 10 false BRAKE! 3.417,2.76 4.396,3.063 0.979,0.302 10 false Not Illuminated 3.583,3.25 4.167,3.531 0.583,0.281 10 false Sounds 5.104,2.01 6.969,2.573 1.865,0.563 10 false Object Detected Acceleration Reduced 5.552,4.302 6.729,4.688 1.177,0.385 10 false (Not displayed) 0.083,6.396 6.708,6.615 6.625,0.219 10 false This illustration is only for explaining what happens when a stationary object is detected. 1.229,1.344 2.427,1.646 1.198,0.302 10 false Situation 3.594,4.354 4.333,4.563 0.74,0.208 10 false BRAKE! 3.615,4.844 4.354,5.052 0.74,0.208 10 false BRAKE! 5.573,2.75 6.552,3.052 0.979,0.302 10 false Not Illuminated 5.698,3.25 6.521,3.563 0.823,0.313 10 false Sounds 5.573,4.875 6.75,5.26 1.177,0.385 10 false (Not displayed) 0.104,5.99 3.479,6.323 3.375,0.333 10 false *2: Models with panoramic view monitor system 0.115,5.563 3.49,5.896 3.375,0.333 10 false *1: Models with Headup Display 1.156,3.719 2.688,4.01 1.531,0.292 10 false Master Warning Light 3.656,3.771 4.531,4.052 0.875,0.281 10 false Blinks 5.76,3.76 6.635,4.042 0.875,0.281 10 false Blinks


iv.

When the system determines that there is a high possibility of a collision even after the above operations, brake control is performed in addition to drive force suppression control.

Drive Force Suppression Control and Brake Control 1
Y272265E01
0.917,0.583 2.052,0.885 1.135,0.302 10 false Vehicle Condition 1.052,1.667 1.656,1.938 0.604,0.271 10 false Situation 2.865,1.438 4.885,2.094 2.021,0.656 10 false High possibility of a collision and brake pedal is not depressed 5.115,1.354 6.958,2 1.844,0.646 10 false Vehicle is stopped by system operation and accelerator pedal is depressed 0.104,3.833 0.906,4.75 0.802,0.917 10 false Combination Meter Assembly 1.125,3.26 2.708,3.552 1.583,0.292 10 false Multi-information Display 1.24,3.958 2.573,4.271 1.333,0.313 10 false PKSB OFF Indicator 1.375,4.552 2.521,4.813 1.146,0.26 10 false Meter Buzzer 3.563,3.25 4.323,3.5 0.76,0.25 10 false BRAKE! 0.188,5.719 2.74,6 2.552,0.281 10 false Radio and Display Receiver Assembly*2 0.896,6.74 2.542,7.073 1.646,0.333 10 false Headup Display*1 3.458,3.99 4.438,4.25 0.979,0.26 10 false Not Illuminated 3.594,4.563 4.354,4.813 0.76,0.25 10 false Sounds 5.521,3.26 6.583,3.552 1.063,0.292 10 false Switch to Brake 5.688,3.99 6.448,4.26 0.76,0.271 10 false Illuminates 5.448,5.677 6.677,5.958 1.229,0.281 10 false Press Brake Pedal 0.083,8.396 6.948,8.646 6.865,0.25 10 false This illustration is only for explaining what happens when a stationary object is detected. 3.604,5.729 4.365,5.979 0.76,0.25 10 false BRAKE! 3.615,6.75 4.375,7 0.76,0.25 10 false BRAKE! 5.792,4.51 6.552,4.76 0.76,0.25 10 false Sounds 5.552,6.99 6.615,7.281 1.063,0.292 10 false Switch to Brake 0.115,8.021 3.531,8.281 3.417,0.26 10 false *2: Models with panoramic view monitor system 0.125,7.688 2.385,7.99 2.26,0.302 10 false 1*: Models with Headup Display 1.26,5.083 2.719,5.396 1.458,0.313 10 false Master Warning Light 3.656,5.063 4.417,5.313 0.76,0.25 10 false Blinks 5.833,5.083 6.594,5.333 0.76,0.25 10 false Blinks

Drive Force Suppression Control and Brake Control 2
Y272266E01
0.083,8.5 7.094,8.813 7.01,0.313 10 false This illustration is only for explaining what happens when a stationary object is detected. 0.813,0.604 1.948,0.896 1.135,0.292 10 false Vehicle Condition 1.052,1.677 1.667,1.875 0.615,0.198 10 false Situation 3.719,1.573 6.427,2.01 2.708,0.438 10 false Vehicle is stopped by system operation and accelerator pedal is not depressed 0.115,3.771 0.917,4.573 0.802,0.802 10 false Combination Meter Assembly 1.115,2.979 2.708,3.292 1.594,0.313 10 false Multi-information Display 1.292,3.969 2.604,4.26 1.313,0.292 10 false PKSB OFF Indicator 0.177,5.677 2.875,6.031 2.698,0.354 10 false Radio and Display Receiver Assembly*2 4.333,3.427 5.552,3.74 1.219,0.313 10 false Press Brake Pedal 4.563,4 5.313,4.292 0.75,0.292 10 false Illuminates 4.635,4.531 5.448,4.823 0.813,0.292 10 false Sounds 0.854,6.698 1.958,7 1.104,0.302 10 false Headup Display*1 4.333,5.677 5.552,5.99 1.219,0.313 10 false Press Brake Pedal 4.25,7.115 5.469,7.427 1.219,0.313 10 false Press Brake Pedal 0.125,8.094 3.24,8.406 3.115,0.313 10 false *2: Models with panoramic view monitor system 0.125,7.75 3.24,8.063 3.115,0.313 10 false *1: Models with Headup Display 1.438,4.531 2.896,4.813 1.458,0.281 10 false Meter Buzzer 1.271,5.063 2.729,5.344 1.458,0.281 10 false Master Warning Light 4.635,5.073 5.448,5.365 0.813,0.292 10 false Blinks




FUNCTION


a.

Parking Support Brake System Operation

i.

The combination meter assembly customization setting can be used to turn the parking support brake system on and off.


ii.

A PKSB OFF indicator is added to make it possible to check that the parking support brake system is off in the combination meter assembly. When the parking support brake system is off, the PKSB OFF indicator illuminates.




FAIL-SAFE


a.

When the clearance warning ECU assembly detects a malfunction in the system, the system enters fail-safe mode. For details, refer to the Repair Manual.



DIAGNOSIS


a.

In order to make system inspections easier to perform, a diagnosis function is used in consideration of serviceability. The DTCs of malfunctioning parts can be read by connecting the Techstream. Refer to the Repair Manual for details.