FUNCTION OF MAIN COMPONENTS
| Component | Function |
|---|---|
| Front Television Camera Assembly | Outputs a video signal of the area in front of the vehicle to the television camera controller. |
| Rear Television Camera Assembly | ·
Outputs a video signal of the area to the rear of the vehicle to the television camera controller. ·
When a pedestrian is detected, sends the pedestrian detection information signal to the television camera controller and blind spot monitor sensor RH. |
| Side Television Camera Assembly LH | Outputs a video signal of the area to the left side of the vehicle to the television camera controller. |
| Side Television Camera Assembly RH | Outputs a video signal of the area to the right side of the vehicle to the television camera controller. |
| Television Camera Controller | ·
Combines video signals from the front, rear, left and right television camera assemblies to create a seamless overhead image. ·
Calculates each guide line based on information signals from each ECU and sensor, combines the lines with the panoramic view and images from each television camera assembly, and outputs a video signal to the radio and display receiver assembly. ·
Turns each television camera assembly on and off according to the input shift position signal and panoramic view monitor switch signal. ·
Combines detection information with the currently displayed panoramic view monitor system screen according to signals from the rear television camera assembly, clearance warning ECU assembly or blind spot monitor sensor RH/LH and outputs a video signal to the radio and display receiver assembly. |
| Radio and Display Receiver Assembly | ·
Displays image information received from the television camera controller. ·
Sends the screen button operation signal to the television camera controller. |
| Panoramic View Monitor Switch | Switches the panoramic view monitor system screen display. |
| Steering Sensor | Detects the angle of the steering wheel and sends the resulting signals to the television camera controller. |
| Shift Lever Position Sensor | Sends the shift position signal to the hybrid vehicle control ECU assembly. |
| Hybrid Vehicle Control ECU Assembly | Sends received shift position signals to the television camera controller. |
| Brake Booster with Master Cylinder Assembly
·
Skid Control ECU |
Sends received vehicle speed signals to the television camera controller. |
| Main Body ECU (Multiplex Network Body ECU) | Sends the front door and luggage compartment door opening and closing signals, etc., to the television camera controller. |
| Clearance Warning ECU Assembly | Sends clearance sonar information signal to the television camera controller. |
| Blind Spot Monitor Sensor RH/LH | ·
Sends RCTA information signal to the television camera controller. ·
Receives the pedestrian detection information signal from the rear television camera assembly and sounds the rear camera detection buzzer (blind spot monitor buzzer). |
| Rear Camera Detection Buzzer (Blind Spot Monitor Buzzer) | Sounds when a pedestrian is detected while the driver is reversing. |
OPERATING CONDITION
Manual display mode and automatic display mode are provided for the display method of the panoramic view monitor system.
Manual Display Mode
Manual display mode is a method of displaying the panoramic view monitor system screen according to the needs of the driver via operation of the panoramic view monitor switch.
The panoramic view monitor system is displayed by operating the panoramic view monitor switch when vehicle speed is approximately 20 km/h (12 mph) or less.
When the vehicle speed exceeds approximately 20 km/h (12 mph), the panoramic view monitor system screen ends and switches to display the navigation screen or information screen.
Automatic Display Mode
When starting off and stopping the vehicle in automatic display mode, it is possible to display the "panoramic view and wide front view" or "dual side view" automatically instead of by pressing the panoramic view monitor switch.
The automatic display mode can be set with the auto mode button displayed on the screen.
| Display | Screen Display Conditions | Objective | Assumed Situation |
|---|---|---|---|
| Display when starting off | Vehicle speed is 10 km/h (6 mph) or less and shift position is not P or R | Reminder to check surroundings | Check surroundings |
| Display when stopping vehicle | Shift position is not P or R and vehicle speed becomes 10 km/h (6 mph) or less | Reduce switch operations | ·
Check forward blind spot ·
Check inside blind spot ·
Check vehicle width ·
Check vehicle-to-vehicle distance |
When the TOYOTA parking assist-sensor system detects an obstacle while driving at a low speed, the monitor screen automatically changes from the current screen (navigation screen, DVD screen, etc.) to the clearance information screen with the "panoramic view and wide front view" screen.
When all of the following conditions are met, the panoramic view and wide front view will be displayed.
·
The shift position is not P or R. ·
The TOYOTA parking assist-sensor system has detected a stationary object. |
When either of the following conditions is met, the panoramic view and wide front view will be canceled and return to its original screen.
·
The TOYOTA parking assist-sensor system does not detect a stationary object. |
FUNCTION
Panoramic View Monitor System Screen and Operation
Each screen of the panoramic view monitor system displays guide lines, estimated course lines, etc., to inform the driver of the tire positions and trajectories which cannot be directly seen from the driver seat, according to the selected screen display mode.
When the TOYOTA parking assist-sensor system detects an obstacle or the RCTA function detects a vehicle approaching from the right or left at the rear of the vehicle, TOYOTA parking assist-sensor system information or RCTA function information is superimposed on the screen according to the selected screen display mode.
Panoramic View and Wide Front View
The panoramic view created by combining images from each television camera assembly and the image from the front television camera assembly are displayed simultaneously. The images assist the driver to confirm the safety of the surroundings and areas to the left and right of the vehicle at locations with poor visibility, such as intersections and T-junctions.
The illustration shown is an example only. The illustration may differ from the actual vehicle screen.
| Item | Description | |
|---|---|---|
| (1) | Wide Front View | An image captured by the front television camera assembly of the area in front of the vehicle. |
| (2) | Front Distance Guide Line (Blue) | These lines are distance guide lines showing the distance forward from the edge of the front bumper. [Approximately 1.0 m (3.3 ft.)] |
| (3) | Auto Mode Button | Is used to turn the automatic display mode on and off. When the automatic display mode is on, the switch indicator illuminates. |
| (4) | Camera Direction Display Vehicle Icon | Indicates that the wide front view is displayed. |
| (5) | Guide Line Switching Button | Changes the guide line display mode. |
| (6) | Panoramic View Vehicle Icon*1 | Displays the vehicle position in the panoramic view. |
| (7) | Panoramic View | An overhead image of the vehicle created by combining images from the front, rear, left and right side television camera assemblies. |
| (8) | Forward Estimated Course Line (Yellow) | Displays the estimated course calculated from the steering angle.
(Displays when the steering wheel is operated more than 90° to either side.) |
| (9) | TOYOTA parking assist-sensor system Information | If a stationary object is detected when the TOYOTA parking assist-sensor system is activated, the approximate distance between the vehicle and the stationary object is displayed. |
| (10) | Masking | Since the lens of the front television camera assembly may affect the perceived distance to objects in certain areas of the image, masking is used. |
| (11) | Parking Support Brake System Information*2 | Displayed when the parking support brake system detects an operation target with which the vehicle could collide. |
*1: The color of the panoramic view vehicle icon can be changed. Refer to the Repair Manual for the details.
*2: Models with parking support brake system
Estimated Course Line Display Mode
The forward estimated course lines represent the estimated course of the vehicle. By turning the steering wheel so that no objects are within the estimated course lines, the driver can easily maneuver the vehicle around objects.
| *a | Forward Estimated Course Line | *b | The illustration shown is an example only. The illustration may differ from the actual vehicle screen. |
Distance Guide Line Display Mode
The front distance guide lines inform the driver of the vehicles relative location when driving into a parking space. By aligning the front distance guide lines with the end of the parking space and the parking space lines, the driver can easily position the vehicle within the parking space.
| *a | Front Distance Guide Line | *b | Parking Space Line |
| *c | The illustration shown is an example only. The illustration may differ from the actual vehicle screen. | - | - |
Side View and Wide Front View (When Outer Rear View Mirror Assemblies are Retracted)
When the outer rear view mirror assemblies are retracted, the panoramic view does not display. Instead, an enlarged image from the side television camera RH and the wide front view are displayed to assist the driver to confirm the safety of the surroundings and park close to objects.
The illustration shown is an example only. The illustration may differ from the actual vehicle screen.
| Item | Description | |
|---|---|---|
| (1) | Wide Front View | An image captured by the front television camera assembly of the area in front of the vehicle. |
| (2) | Side View (Right Side) | An image of the area to the right of the vehicle captured by the side television camera assembly RH. |
| (3) | Warning Message | Warns the driver according to the message on the display. |
Dual Side View
The images from the left and right television camera assemblies are displayed simultaneously. As a result, this helps the driver confirm the safety of the areas to the sides of the vehicle and avoid contact with obstacles on narrow roads.
The illustration shown is an example only. The illustration may differ from the actual vehicle screen.
| Item | Description | |
|---|---|---|
| (1) | Front Distance Guide Line (Red) | These lines are distance guide lines showing the distance forward from the edge of the front bumper. [Approximately 0.5 m (1.6 ft.)] |
| (2) | Vehicle Width Parallel Line (Blue) | A vehicle width guide line including the outer rear view mirror assembly. |
| (3) | Front Tire Contact Line (Blue) | A guide line showing the front tire contact position. |
| (4) | Side View (Left Side) | An image captured by the side television camera assembly LH of the area from the left front corner of the vehicle. |
| (5) | Auto Mode Button | Is used to turn the automatic display mode on and off. When the automatic display mode is on, the switch indicator illuminates. |
| (6) | Camera Direction Display Vehicle Icon | Indicates that the wide front view is displayed. |
| (7) | Side View (Right Side) | An image captured by the side television camera assembly RH of the area from the right front corner of the vehicle. |
| (8) | TOYOTA parking assist-sensor system Information | If a stationary object is detected when the TOYOTA parking assist-sensor system is activated, the approximate distance between the vehicle and the stationary object is displayed. |
Vehicle Width Parallel Line
The vehicle width parallel lines are used as a guide to know the approximate width of the vehicle including the outer rear view mirrors. By driving forward while steering so that the vehicle width parallel lines do not overlap actual obstacles, white lines, curbs, etc., the vehicle can avoid obstacles and drive close to objects on narrow roads.
| *a | Vehicle Width Parallel Line | *b | Narrow Road, etc. |
| *c | Wall, Fence, etc. | *d | The illustration shown is an example only. The illustration may differ from the actual vehicle screen. |
Panoramic View and Rear View
The panoramic view created by combining images from the front, rear, left and right side television camera assemblies and the image from the television camera assembly are displayed simultaneously. The images assist the driver to confirm the safety of the surroundings when operating the vehicle in reverse.
The illustration shown is an example only. The illustration may differ from the actual vehicle screen.
| Item | Description | |
|---|---|---|
| (1) | Rear View | An image captured by the television camera assembly of the area to the rear of the vehicle. |
| (2) | Rear Vehicle Width Guide Line (Blue) | Indicates the estimated vehicle width. |
| (3) | RCTA Icon | If a vehicle is detected when the RCTA function is activated, the direction of the approaching vehicle is displayed. |
| (4) | Display Mode Switching Button | Changes the display mode. |
| (5) | Rear Distance Guide Line (Blue) | These lines are distance guide lines showing the distance from the edge of the rear bumper. [Approximately 0.5 m (1.6 ft.)] |
| (6) | Rear Distance Guide Line (Yellow/Red) | These lines are distance guide lines showing the distance from the edge of the rear bumper. [Approximately 1.0 m (3.3 ft.): yellow, approximately 0.5 m (1.6 ft.): red] |
| (7) | Guide Line Switching Button | Changes the guide line display mode. |
| (8) | Rear Estimated Course Line (Yellow) | Moves in sync with the steering wheel to indicate the estimated reverse course of the vehicle. |
| (9) | Panoramic View Vehicle Icon*1 | Displays the vehicle position in the panoramic view. |
| (10) | TOYOTA parking assist-sensor system Information | If a stationary object is detected when the TOYOTA parking assist-sensor system is activated, the approximate distance between the vehicle and the stationary object is displayed. |
| (11) | Panoramic View | An overhead image of the vehicle created by combining images from the front, rear, left and right side television camera assemblies. |
| (12) | Front Distance Guide Line (Blue) | These lines are distance guide lines showing the distance forward from the edge of the front bumper. [Approximately 1.0 m (3.3 ft.)] |
| (13) | Side Estimated Course Line (Yellow) | ·
Displays the estimated course calculated from the steering angle. ·
Displays the estimated course on the outside of the steering direction. |
| (14) | Parking Assist Guide Line (Blue) | Indicates the path the vehicle will follow when the driver turns the steering wheel fully. |
| (15) | Vehicle Center Guide Line (Blue) | Indicates the estimated position on the ground of the center of the vehicle. |
| (16) | Parking Support Brake System Information*2 | Displayed when the parking support brake system detects an operation target with which the vehicle could collide. |
| (17) | Pedestrian Detection Icon | If a pedestrian is detected, a pedestrian detection icon is displayed. |
| (18) | RCD OFF Indicator | When the rear camera detection function is malfunctioning or unavailable, RCD (Rear Camera Detection) OFF indicator is displayed. |
*1: The color of the panoramic view vehicle icon can be changed. Refer to the Repair Manual for the details.
*2: Models with parking support brake system
Estimated Course Line Display Mode (Perpendicular Parking)
The estimated course lines inform the driver of the estimated course of the vehicle based on the current steering angle. When reversing, by turning the steering wheel so that the estimated course lines are correctly positioned with respect to the parking space lines, the driver can easily position the vehicle within the parking space. Also, the estimated course lines assist the driver to avoid obstacles.
The rear vehicle width guide lines can be used to determine whether the vehicle is parked straight in the parking space by confirming whether the parking space lines and rear vehicle width guide lines are crossed or parallel.
| *a | Parking Space Line | *b | Rear Vehicle Width Guide Line |
| *c | Rear Estimated Course Line | *d | The illustration shown is an example only. The illustration may differ from the actual vehicle screen. |
Estimated Course Line Display Mode (Parallel Parking)
The estimated course lines inform the driver of the estimated course of the vehicle based on the current steering angle. By turning the steering wheel so that the estimated course lines are correctly positioned with respect to the side of the road or parking space line, the driver can easily position the vehicle within the parking space. Also, the estimated course lines assist the driver to avoid obstacles.
The rear vehicle width guide lines can be used to determine whether the vehicle is parked straight in the desired parking position by confirming the status of the shoulder and parking space lines, etc., and rear vehicle width guide lines.
| *a | Shoulder and Parking Space Lines, etc. | *b | Rear Estimated Course Line |
| *c | Rear Vehicle Width Guide Line | *d | Side Estimated Course Line |
| *e | The illustration shown is an example only. The illustration may differ from the actual vehicle screen. | - | - |
Parking Assist Guide Line Display Mode (Perpendicular Parking)
The parking assist guide lines inform the driver of the course of the vehicle when the steering wheel is turned to full lock while driving in reverse. By driving the vehicle in reverse until the parking assist guide lines align with the parking space line, the vehicle can be guided to the position at which the driver should start turning the steering wheel.
| *a | Parking Space Line | *b | Parking Assist Guide Line |
| *c | The illustration shown is an example only. The illustration may differ from the actual vehicle screen. | - | - |
Parking Assist Guide Line Display Mode (Parallel Parking)
The parking assist guide lines inform the driver of the course of the vehicle when the steering wheel is turned to full lock while driving in reverse. By driving the vehicle in reverse until the parking assist guide lines align with the side of the road or parking space line, the vehicle can be guided to the position at which the driver should start turning the steering wheel.
| *a | Parking Assist Guide Line | *b | Parking Space Line |
| *c | The illustration shown is an example only. The illustration may differ from the actual vehicle screen. | - | - |
Rear View/Wide Rear View
The image from the television camera assembly is displayed. The images assist the driver to confirm the safety of the surroundings when operating the vehicle in reverse.
The illustration shown is an example only. The illustration may differ from the actual vehicle screen.
| Item | Description | |
|---|---|---|
| (1) | Rear View/Wide Rear View | An image captured by the television camera assembly of the area to the rear of the vehicle. |
| (2) | Rear Vehicle Width Guide Line (Blue) | Indicates the estimated vehicle width. |
| (3) | RCTA Icon | If a vehicle is detected when the RCTA function is activated, the direction of the approaching vehicle is displayed. |
| (4) | Display Mode Switching Button | Changes the display mode. |
| (5) | Rear Distance Guide Line (Blue) | These lines are distance guide lines showing the distance from the edge of the rear bumper. [Approximately 0.5 m (1.6 ft.)] |
| (6) | Rear Distance Guide Line (Yellow/Red) | These lines are distance guide lines showing the distance from the edge of the rear bumper. [Approximately 1.0 m (3.3 ft.): yellow, approximately 0.5 m (1.6 ft.): red] |
| (7) | Guide Line Switching Button | Changes the guide line display mode. |
| (8) | TOYOTA parking assist-sensor system Information | If a stationary object is detected when the TOYOTA parking assist-sensor system is activated, the approximate distance between the vehicle and the stationary object is displayed. |
| (9) | Parking Assist Guide Line (Blue) | Indicates the path the vehicle will follow when the driver turns the steering wheel fully. |
| (10) | Vehicle Center Guide Line (Blue) | Indicates the estimated position on the ground of the center of the vehicle. |
| (11) | Rear Estimated Course Line (Yellow) | Moves in sync with the steering wheel to indicate the estimated reverse course of the vehicle. |
| (12) | Warning Message | Warns the driver according to the message on the display. |
Side View and Rear View (when Outer Rear View Mirror Assemblies are Retracted)
When the outer rear view mirror assemblies are retracted, the side television camera assembly RH and rear television camera assembly images simultaneously display and assist the driver to confirm the safety of the surroundings and park close to the curb or parking space boundary line.
The illustration shown is an example only. The illustration may differ from the actual vehicle screen.
| Item | Description | |
|---|---|---|
| (1) | Rear View | An image captured by the rear television camera assembly of the area to the rear of the vehicle. |
| (2) | Side View (Right Side) | An image of the area to the right of the vehicle captured by the side television camera assembly RH. |
| (3) | Warning Message | Warns the driver according to the message on the display. |
Moving View
This view combines images from the front, rear, left and right side television camera assemblies to display an image of the vehicle from a viewpoint diagonally above the vehicle. The displayed image rotates 360 degrees around the vehicle displayed on the screen to assist the driver to confirm the safety of the surroundings. Furthermore, after the image of the vehicle from a viewpoint diagonally above the vehicle rotates a full 360 degrees, an overhead view of the vehicle is displayed.
Using the rotation pause button, the rotation of the moving view can be paused and unpaused at will.
When all of the following conditions are met, the moving view will be displayed.
·
Shift position is P. ·
TOYOTA parking assist-sensor system is on. ·
Panoramic view monitor switch is pressed. |
The illustration shown is an example only. The illustration may differ from the actual vehicle screen.
| Item | Description | |
|---|---|---|
| (1) | Body Color Setting Switch | Displays the body color setting screen. |
| (2) | Display Mode Switching Button | Changes the display mode. |
| (3) | Rotation Pause Button | Pauses and unpauses the rotation of the moving view. |
When the shift position is changed to D or N while the moving view screen is displayed, the screen transitions to the panoramic view and wide front view screen.
The driver can change the body color of the vehicle icon displayed by the panoramic view monitor system to the desired color via the body color setting screen.
See Through View
By combining the images from cameras on the front, rear, and both sides of the vehicle, a simulated video display of the area around the vehicle is created. By reducing the size of blind spots from inside the vehicle, it assists the driver to confirm the safety of the area around the vehicle.
Using the rotation pause button, the rotation of the see through view can be paused and unpaused at will.
When all of the following conditions are met, the see through view will be displayed.
·
Shift position is P. ·
TOYOTA parking assist-sensor system is on. ·
Panoramic view monitor switch is pressed. |
The illustration shown is an example only. The illustration may differ from the actual vehicle screen.
| Item | Description | |
|---|---|---|
| (1) | Body Color Setting Switch | Displays the body color setting screen. |
| (2) | Display Mode Switching Button | Changes the display mode. |
| (3) | Rotation Pause Button | Pauses and unpauses the rotation of the moving view. |
When the shift position is changed to D or N while the moving view screen is displayed, the screen transitions to the panoramic view and wide front view screen.
The driver can change the body color of the vehicle icon displayed by the panoramic view monitor system to the desired color via the body color setting screen.
Panoramic View Zoom Function
If objects on the monitor are small and difficult to see while the panoramic view screen is displayed, this function can enlarge either the front left/right or back left/right area.
Either the front left/right or back left/right area of the panoramic view screen can be selected to enlarge the selected area.
| *a | Panoramic View and Wide Front View | *b | Panoramic View and Rear View |
The illustration shown is an example only. The illustration may differ from the actual vehicle screen.
The panoramic view enlarged display differs from the normal panoramic view screen and does not display guide lines.
When all of the following conditions are met, the panoramic view magnification function can be used.
·
The vehicle speed is approximately 20 km/h (12 mph) or less ·
TOYOTA parking assist-sensor system is on. |
When any of the following conditions are met, the panoramic view magnification function is automatically canceled.
·
The vehicle speed is approximately 20 km/h (12 mph) or more ·
TOYOTA parking assist-sensor system is off. |
Panoramic View Monitor System Screen Transition
The panoramic view monitor system assists the driver to confirm the conditions around the vehicle while driving at low speeds and when parking.
| *A | Shift Position P | *B | Except Shift Position P or R |
| *C | Shift Position R | - | - |
| *a | Moving View | *b | See Through View |
| *c | Navigation Display etc. | *d | Panoramic View and Wide Front View |
| *e | Dual Side View | *f | Panoramic View and Rear View |
| *g | Wide Rear View | *h | Rear View |
| *i | Panoramic View Monitor Switch is Pressed. | *j | Shift Position Operation |
| *k | Display Mode Switching Button is Pressed. | *l | The illustration shown is an example only. The illustration may differ from the actual vehicle screen. |
DIAGNOSIS
The television camera controller is equipped with a diagnosis function which can display a diagnosis menu for the panoramic view monitor system. For details, refer to the Repair Manual.