Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › BRAKE ACTUATOR(for RHD)
RM33C0E _54 Brake _065442 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0319338 BRAKE ACTUATOR(for RHD) G

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  BRAKE ACTUATOR(for RHD)  INSPECTION  


PROCEDURE

Hide 44510 1.INSPECT BRAKE ACTUATOR ASSEMBLY

a.

Inspect the solenoid circuit.

i.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.


C379335C07
1.781,0.552 2.167,1.531 true 3,2.406 2.698,1.656 true 2.271,2.49 2.51,1.646 true 1.76,2.167 2.302,1.646 true 3.76,1.177 3.969,0.448 true 5.438,0.51 5.052,1.542 true 5.552,2.135 4.823,1.656 true 5.01,2.469 4.656,1.656 true 4.104,2.417 4.448,1.656 true 1.583,2.167 2.198,2.365 0.615,0.198 10 false SRLH 2.906,2.406 3.521,2.604 0.615,0.198 10 false SFLH 5.479,2.125 6.094,2.323 0.615,0.198 10 false SRLR 3.958,2.406 4.573,2.604 0.615,0.198 10 false SFLR 4.896,2.469 5.51,2.667 0.615,0.198 10 false SRRR 5.323,0.333 5.938,0.531 0.615,0.198 10 false SFRR 2.083,2.479 2.698,2.677 0.615,0.198 10 false SRRH 1.615,0.375 2.229,0.573 0.615,0.198 10 false SFRH 3.865,0.26 4.479,0.458 0.615,0.198 10 false +BS 0.26,0.198 0.875,0.396 0.615,0.198 10 false *a
*a Component without harness connected
(Brake Actuator Assembly)
- -



ii.

Disconnect the brake actuator assembly connector.


iii.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



iv.

Measure the resistance according to the value(s) in the table below.

HINT:

Check the brake actuator assembly when it is cooled down.


Standard Resistance:
Tester Connection Condition Specified Condition
5 (+BS) - 31 (SFRH) Always 6.4 to 7.0 Ω
5 (+BS) - 28 (SFLH) Always 6.4 to 7.0 Ω
5 (+BS) - 29 (SRRH) Always 6.4 to 7.0 Ω
5 (+BS) - 30 (SRLH) Always 6.4 to 7.0 Ω
5 (+BS) - 15 (SFRR) Always 5.1 to 5.7 Ω
5 (+BS) - 18 (SFLR) Always 5.1 to 5.7 Ω
5 (+BS) - 17 (SRRR) Always 5.1 to 5.7 Ω
5 (+BS) - 16 (SRLR) Always 5.1 to 5.7 Ω


If the result is not as specified, replace the brake actuator assembly.