44785D
1.INSTALL BRAKE MASTER CYLINDER GASKET
Install a new brake master cylinder gasket to the brake booster with master cylinder assembly.
47210L
2.INSTALL BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY
| *a | Skid Control ECU |
| *b | No. 1 Reservoir Hose |
| *c | Brake Master Cylinder Push Rod Clevis |
| *d | Boot |
| *e | Master Cylinder Reservoir Assembly |
| *f | Brake Actuator Bracket |
Install the brake booster with master cylinder assembly with the 4 nuts.
Do not kink or damage the brake lines.
Do not carry the brake booster with master cylinder assembly by the parts shown in the illustration.
Be careful not to allow brake fluid to enter the connector.
If installing a new brake booster with master cylinder assembly, do not remove the hole plugs before connecting the brake lines because the brake booster with master cylinder assembly is filled with brake fluid.
47264A
3.INSTALL PUSH ROD PIN
|
Lithium Soap Base Glycol Grease |
Apply lithium soap base glycol grease to the push rod pin.
Connect the brake master cylinder push rod clevis to the brake pedal support assembly with the push rod pin, and install a new clip as shown in the illustration.
The push rod pin can be installed in either direction.
78111
4.INSTALL ACCELERATOR PEDAL
5.CONNECT BRAKE LINE
| *a | Torque Wrench Fulcrum Length |
| *b | Union Nut Wrench |
Using a union nut wrench, connect the 3 brake lines to the brake booster with master cylinder assembly.
Do not kink or damage the brake lines.
Do not allow the brake lines to twist or interfere with other parts or the vehicle body during tightening.
Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.
Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
When using a union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)):
13.4 N*m (137 kgf*cm, 10 ft.*lbf)
44571A
6.CONNECT NO. 1 BRAKE ACTUATOR HOSE
| *a | Identification Mark |
|
Front of the vehicle |
Connect the No. 1 brake actuator hose to the brake booster with master cylinder assembly and slide the clip to secure it.
Make sure to connect the No. 1 brake actuator hose with its identification mark facing the front of the vehicle.
Install the clip within the range shown in the illustration.
82111
7.INSTALL ENGINE ROOM MAIN WIRE
|
Connect the connector |
|
Lock the lock lever |
Connect the connector to the brake booster with master cylinder assembly and lock the lock lever as shown in the illustration.
Make sure that the connector is locked securely.
Make sure that the connector can be connected smoothly.
Do not allow water, oil or dirt to enter the connector.
Engage the clamp to install the engine room main wire.
Connect the connector to the brake booster with master cylinder assembly.
44551C
8.BLEED NO. 1 BRAKE ACTUATOR TUBE
Make sure to bleed the air from the No. 1 brake actuator tube. If the air remains in the No. 1 brake actuator tube, the air will enter the brake booster pump assembly and may damage the brake booster pump assembly.
Remove the brake master cylinder reservoir filler cap assembly.
Add brake fluid to the reservoir until the fluid level is between the MAX and MIN lines on the brake fluid reservoir.
SAE J1703 or FMVSS No. 116 DOT3
SAE J1704 or FMVSS No. 116 DOT4
Remove the 2 nuts to separate the No. 1 brake actuator tube.
If the No. 1 brake actuator tube has already been separated, it is not necessary to perform this step.
Set SST to the brake master cylinder reservoir assembly.
Using SST, increase and then maintain the pressure in the brake master cylinder reservoir assembly for 60 seconds.(*1)
50 to 80 kPa (0.6 to 0.8 kgf/cm2, 7.3 to 11.6 psi)
Release the pressure in the brake master cylinder reservoir assembly and wait for 30 seconds.(*2)
Repeat steps *1 to *2, 3 times.
Remove SST.
|
Pull up |
Elevate the No. 1 brake actuator tube for 10 seconds by lifting the No. 1 brake actuator tube as shown in the illustration.(*3)
Do not damage the hoses by applying excessive force.
Repeat step *3, 5 times.
|
Pull up |
Elevate the No. 1 brake actuator tube for 10 seconds by lifting the No. 1 brake actuator tube as shown in the illustration.(*4)
Do not damage the hoses by applying excessive force.
|
Press down |
Lower the No. 1 brake actuator tube for 10 seconds as shown in the illustration.(*5)
Do not damage the hoses by applying excessive force.
Repeat steps *4 to *5, 5 times.
Install the No. 1 brake actuator tube with the 2 nuts.
9.CONNECT BRAKE BOOSTER PUMP CONNECTOR
Perform this operation only when the accumulator pressure zero down operation could not be performed using the GTS.
|
Connect the connector |
|
Lock the lock lever |
Connect the connector to the brake booster pump assembly and lock the lock lever as shown in the illustration.
Make sure that the connector is locked securely.
Make sure that the connector can be connected smoothly.
Do not allow water, oil or dirt to enter the connector.
10.FILL RESERVOIR WITH BRAKE FLUID
11.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL
12.BLEED BRAKE SYSTEM
13.INSPECT AND ADJUST BRAKE PEDAL
14. OBTAIN ZERO POINT OF YAW RATE AND ACCELERATION SENSOR
12601B
15.INSTALL NO. 1 ENGINE COVER SUB-ASSEMBLY
53607A
16.INSTALL FRONT CENTER UPPER SUSPENSION BRACE SUB-ASSEMBLY
Temporarily install the front center upper suspension brace sub-assembly with the 6 bolts and 4 nuts.
Fully tighten the 2 nuts (A).
Fully tighten the 6 bolts and 2 nuts (B) to install the front center upper suspension brace sub-assembly.
| Bolt Color | Torque |
|---|---|
| Black | 8.0 N*m (82 kgf*cm, 71 in.*lbf) |
| Silver | 8.9 N*m (91 kgf*cm, 79 in.*lbf) |
Engage the 3 clamps to install the wire harness.
Connect the connector.
55708
17.INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY