Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE BOOSTER PUMP(for LHD)
RM33C0E _54 Brake _065443 BRAKE SYSTEM (OTHER) _0319353 BRAKE BOOSTER PUMP(for LHD) A

BRAKE SYSTEM (OTHER)  BRAKE BOOSTER PUMP(for LHD)  INSTALLATION  


PROCEDURE

Hide 44572C 1.INSTALL NO. 2 BRAKE ACTUATOR HOSE

a.
C378053C01
2.406,1.75 2.219,1.75 2.219,1.75 2.042,1.531 true 2.438,1.667 2.635,1.854 0.198,0.188 10 false *a 2.698,2.927 3.313,3.125 0.615,0.198 10 false 235°
*a Identification Mark
V100136

Front of the vehicle


Install the No. 2 brake actuator hose to the brake booster pump assembly and slide the clip to secure it.

NOTICE:
·

Make sure to connect the No. 2 brake actuator hose with its identification mark facing the front of the vehicle.

·

Install the clip within the range shown in the illustration.




Hide 47070 2.INSTALL BRAKE BOOSTER PUMP ASSEMBLY

a.
C378054C01
1.125,0.969 1.281,0.969 true 0.479,1.063 0.688,1.063 true 1.313,0.896 1.625,1.052 0.313,0.156 10 false *1 0.333,0.979 0.646,1.135 0.313,0.156 10 false *2
*1 Brake Booster Pump Collar
*2 Brake Booster Pump Bushing


Install the 2 brake booster pump collars and 2 brake booster pump bushings to the brake booster pump assembly as shown in the illustration.

HINT:

Perform this procedure only when replacement of the brake booster pump collars or brake booster pump bushings is necessary.



b.

Install the brake booster pump assembly, brake booster pump bushing and brake actuator case collar to the brake actuator bracket assembly as shown in the illustration.

C378050C01
4.344,1.177 4.656,1.177 false 2.969,2.146 3.115,2.146 false 2.469,2.406 2.719,2.406 true 4.292,1.646 4.604,1.646 false 4.75,2.24 4.75,1.948 false 6.042,1.896 5.771,1.896 false 3.146,2.073 3.458,2.229 0.313,0.156 10 false *1 6.063,1.823 6.375,1.979 0.313,0.156 10 false *a 4.198,1.115 4.51,1.271 0.313,0.156 10 false *b 4.146,1.573 4.458,1.729 0.313,0.156 10 false *c 4.677,2.25 4.99,2.406 0.313,0.156 10 false *d 2.313,2.333 2.625,2.49 0.313,0.156 10 false *2
*1 Brake Booster Pump Collar *2 Brake Booster Pump Bushing
*a Union *b Connector
*c Wire Harness *d Stud
V113147

Install in this Direction - -


NOTICE:
·

Be careful not to allow brake fluid to enter the connector.

·

Do not apply excessive force to the brake lines.

·

When installing the brake booster pump assembly to the brake actuator bracket assembly, confirm that the 2 brake booster pump bushings and 2 brake booster pump collars are installed to the brake booster pump assembly.

·

Do not drop the brake booster pump assembly when carrying it.

·

If installing a new brake booster pump assembly, do not remove the hole plugs before connecting the brake lines because the brake booster pump assembly is filled with brake fluid.

·

Do not carry the brake booster pump assembly by the parts shown in the illustration.




c.

Install the nut.

Torque:
6.5 N*m (66 kgf*cm, 58 in.*lbf)


d.
C378048N01
1.885,0.667 2.01,0.854 0.125,0.188 10 true 1 1.51,1.104 1.635,1.292 0.125,0.188 10 true 2

Engage the claw and clamp to install the brake booster pump assembly wire harness to the brake actuator bracket assembly.

NOTICE:

Engage the claw and clamp in the order shown in the illustration.



e.
C377745C01
0,0 0,0 false
V113147

Connect the connector
V113148

Lock the lock lever


Connect the connector to the brake booster pump assembly and lock the lock lever as shown in the illustration.

NOTICE:
·

Make sure that the connector is locked securely.

·

Make sure that the connector can be connected smoothly.

·

Do not allow water, oil or dirt to enter the connector.




Hide 473A1 3.CONNECT ACCUMULATOR TO BRAKE MASTER CYLINDER TUBE

a.
C378047C01
2.885,2.875 2.708,2.875 2.708,2.875 2.708,2.646 false 1.792,2.927 2.104,3.083 0.313,0.156 10 false *a 2.917,2.802 3.229,2.958 0.313,0.156 10 false *b
*a Torque Wrench Fulcrum Length
*b Union Nut Wrench


Using a union nut wrench, connect the accumulator to brake master cylinder tube to the brake booster pump assembly.

Torque:
Specified tightening torque : 15.2 N*m (155 kgf*cm, 11 ft.*lbf)

NOTICE:
·

Do not kink or damage the accumulator to brake master cylinder tube.

·

Do not allow the accumulator to brake master cylinder tube to twist or interfere with other parts or the vehicle body during tightening.

·

Do not allow any foreign matter such as dirt or dust to enter the accumulator to brake master cylinder tube from the connecting parts.



HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)):

13.4 N*m (137 kgf*cm, 10 ft.*lbf)




Hide 44572C 4.CONNECT NO. 2 BRAKE ACTUATOR HOSE

a.
C378045C01
1.448,1.698 1.656,1.698 1.656,1.698 1.802,1.948 true 1.271,1.615 1.458,1.792 0.188,0.177 10 true *a 2,0.208 2.458,0.406 0.458,0.198 10 false 30° 2.406,0.208 2.865,0.406 0.458,0.198 10 false 30°
*a Identification Mark
V100136

Front of the vehicle


Connect the No. 2 brake actuator hose to the No. 1 brake actuator tube and slide the clip to secure it.

NOTICE:
·

When connecting the No. 2 brake actuator hose, face the identification mark up.

·

Install the clip within the range shown in the illustration.




Hide 44551C 5.BLEED NO. 1 BRAKE ACTUATOR TUBE

Hide 6.FILL RESERVOIR WITH BRAKE FLUID

Hide 7.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 8.BLEED BRAKE SYSTEM

Hide 12601B 9.INSTALL NO. 1 ENGINE COVER SUB-ASSEMBLY

Hide 53607A 10.INSTALL FRONT CENTER UPPER SUSPENSION BRACE SUB-ASSEMBLY

Hide 55708 11.INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY