Home › Engine / Hybrid System › A25A-FXS (FUEL) › FUEL PUMP (w/ Canister Pump Module)
RM33C0E _51 Engine / Hybrid System _065421 A25A-FXS FUEL _0319774 FUEL PUMP(w/ Canister Pump Module) A

A25A-FXS FUEL  FUEL PUMP(w/ Canister Pump Module)  INSTALLATION  


PROCEDURE

Hide 77020A 1.INSTALL FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY

a.

Install a new fuel suction tube set gasket to the fuel tank assembly.


b.
A405234

Insert the fuel suction tube with pump and gauge assembly to the fuel tank assembly as shown in the illustration.


c.
A405213N01
1.906,1.135 2.146,0.865 2.146,0.865 2.302,0.865 true 2.344,0.781 2.479,0.948 0.135,0.167 10 true A

Set the part (A) of the fuel suction tube with pump and gauge assembly against the fuel tank assembly, and install the fuel suction tube with pump and gauge assembly to the fuel tank assembly as shown in the illustration.

NOTICE:

Be careful not to bend the arm of the fuel sender gauge assembly.



d.
A405236C01
1.646,1.823 0.688,0.885 0.688,0.885 1.708,0.656 true 1.667,2.646 2.521,2.646 true 0.469,0.781 0.667,0.948 0.198,0.167 10 true *a 1.49,2.552 1.688,2.719 0.198,0.167 10 true *a
*a Protrusion
V100135

Notch


Align the protrusions of the fuel suction tube with pump and gauge assembly with the notches in the fuel tank assembly.


Hide 77144 2.INSTALL FUEL PUMP GAUGE RETAINER

a.

Install the fuel pump gauge retainer.

i.

While pressing down on the fuel suction tube with pump and gauge assembly, temporarily install the fuel pump gauge retainer.


ii.
A405218C01
1.125,0.156 1.417,0.156 true 0.771,0.531 0.938,0.531 0.938,0.531 1.156,0.802 true 0.74,1.25 1.063,1.25 true 2.385,0.583 2.521,0.188 2.521,0.188 2.667,0.188 true 2.385,1.063 2.677,1.063 true 0.76,2.844 1.51,2.844 true 0.583,2.75 0.896,2.906 0.313,0.156 10 false *a 0.938,0.073 1.125,0.24 0.188,0.167 10 true *b 0.563,1.156 0.729,1.333 0.167,0.177 10 true *c 0.594,0.438 0.771,0.604 0.177,0.167 10 true *d 2.719,0.979 2.885,1.156 0.167,0.177 10 true *c 2.708,0.104 2.885,0.271 0.177,0.167 10 true *d
*a Insertion Point
*b SST (Plate)
*c SST (Claw)
*d SST (Bolt)


Temporarily install SST (plate) and SST (claw) to the fuel pump gauge retainer.

SST
09808-14031  (09808-01030, 09808-01050)
09808-01071  

HINT:

Securely insert the ends of SST (claw) into the insertion points in the fuel pump gauge retainer.



iii.

While firmly pressing SST (claw) into the insertion points in the fuel pump gauge retainer, tighten SST (bolt).


iv.
A405238C01
1.396,0.781 1.698,0.781 true 1.083,1.021 1.219,1.021 1.219,1.021 1.448,1.26 true 0.979,1.333 1.281,1.333 true 2.115,1.125 2.281,0.781 2.281,0.781 2.427,0.781 true 1.021,4.146 1.625,4.146 true 1.115,4.531 1.552,4.531 true 0.833,4.042 1.021,4.208 0.188,0.167 10 true *a 0.938,4.448 1.094,4.615 0.156,0.167 10 true *b 1.229,0.688 1.542,0.844 0.313,0.156 10 false *c 0.802,1.25 1.115,1.406 0.313,0.156 10 false *d 0.906,0.917 1.219,1.073 0.313,0.156 10 false *e 2.479,0.698 2.792,0.854 0.313,0.156 10 false *e
*a Triangle Mark (Fuel Pump Gauge Retainer)
*b Triangle Mark (Fuel Tank Assembly)
*c SST (Handle)
*d SST (Plate)
*e SST (Bolt)
V100136

Front Side


Install SST (handle) to SST (plate).

SST
09808-14031  (09808-01010)
09808-01071  


v.

Using SST, rotate the fuel pump gauge retainer so that the triangle mark on the fuel pump gauge retainer is aligned with the triangle mark on the fuel tank assembly to install the fuel suction tube with pump and gauge assembly to the fuel tank assembly.

NOTICE:
·

Do not use any tools other than specified as this may result in damage to the fuel pump gauge retainer or fuel tank assembly.

·

Do not press down on SST excessively as this may make the fuel pump gauge retainer hard to rotate, and may damage components.

·

Make sure to rotate SST (handle) horizontally. If it is rotated at an angle, SST may come off.

·

Do not spin SST too fast or use an impact wrench as this may result in damage to components.

·

If SST comes off of the fuel pump gauge retainer, loosen SST (bolt) and reinstall SST.

·

Make sure that the fuel suction tube set gasket does not come off.





b.

Engage the claw to install the No. 1 fuel tube clamp.


Hide 77209F 3.CONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY

a.

Push the fuel tube joint onto the plug of the fuel suction plate sub-assembly, then install the tube joint clip.

A405241C01
3.938,1.292 5.25,2.708 1.313,1.417 5.708,1.292 7.021,2.708 1.313,1.417 4.865,0.521 5.167,0.521 false 1.573,0.927 1.74,0.927 1.74,0.927 1.854,1.323 true 1.813,2.302 1.813,2.031 true 6.375,1.635 6.375,1.396 6.375,1.396 6.521,1.396 true 4.875,0.792 5.438,0.792 false 4.979,0.792 4.979,0.677 4.979,0.677 5.385,0.677 false 6.031,0.677 6.156,0.906 6.156,0.906 6.271,0.906 false 5.667,0.198 5.885,0.198 false 4.302,1.698 4.542,1.698 false 5.938,1.677 6.115,1.677 false 4.396,2.26 4.521,2.26 4.521,2.26 4.771,1.844 true 6.323,0.833 6.635,0.99 0.313,0.156 10 false *1 4.698,0.438 5.01,0.594 0.313,0.156 10 false *2 1.396,0.844 1.604,1.01 0.208,0.167 10 true *3 5.938,0.115 6.25,0.271 0.313,0.156 10 false *a 4.698,0.708 5.01,0.865 0.313,0.156 10 false *b 4,1.323 4.313,1.479 0.313,0.156 10 false *c 5.771,1.323 6.083,1.479 0.313,0.156 10 false *d 4.229,2.167 4.542,2.323 0.313,0.156 10 false *e 4.146,1.604 4.458,1.76 0.313,0.156 10 false *2 5.781,1.594 6.094,1.75 0.313,0.156 10 false *2 1.74,2.333 2.052,2.49 0.313,0.156 10 false *2 6.573,1.302 6.771,1.51 0.198,0.208 10 true *e
*1 Fuel Suction Plate Sub-assembly *2 Tube Joint Clip
*3 Fuel Tank Main Tube Sub-assembly - -
*a Fuel Tube Joint *b O-ring
*c Correct *d Incorrect
*e Collar - -
V100135

Insert
V100136

Insert


NOTICE:
·

Check that there are no scratches or foreign matter around the connecting parts of the fuel tube joint and plug before performing this work.

·

Check that the fuel tube joint is securely inserted to the end.

·

Check that the tube joint clip is on the collar of the fuel tube joint.

·

After installing the tube joint clip, check that the fuel tank main tube sub-assembly is securely connected by pulling on it.




Hide 77404 4.CONNECT FUEL TANK VENT HOSE SUB-ASSEMBLY

a.

Connect the fuel tank vent hose sub-assembly to the fuel suction tube with pump and gauge assembly.

Click hereEngine / Hybrid System>A25A-FXS (FUEL)>FUEL SYSTEM>PRECAUTION


Hide 89461 5.INSTALL FUEL TANK PRESSURE SENSOR (VAPOR PRESSURE SENSOR)

Hide 58325E 6.INSTALL REAR FLOOR SERVICE HOLE COVER

a.

Remove any remaining butyl tape from the rear floor service hole cover and vehicle body.


b.

Clean the installation surfaces of the rear floor service hole cover and vehicle body.


c.

Connect the 2 fuel pump connectors and fuel tank pressure sensor (vapor pressure sensor) connector.


d.
A405242C02
0.76,0.958 1.031,0.948 true 0.583,0.865 0.76,1.042 0.177,0.177 10 true *a
*a Butyl Tape Adhesion Area


Install the rear floor service hole cover with new butyl tape.

NOTICE:

Securely install the rear floor service hole cover.



Hide 71305A 7.INSTALL CENTER REAR SEATBACK HINGE SUB-ASSEMBLY

a.

Install the center rear seatback hinge sub-assembly to the vehicle body with the 2 bolts.

Torque:
36.8 N*m (375 kgf*cm, 27 ft.*lbf)


Hide 8.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 64718C 9.INSTALL LUGGAGE TRIM SERVICE HOLE COVER

Hide 11.INSTALL REAR SEAT ASSEMBLY

Hide 12.PERFORM INITIALIZATION

a.

Perform "Inspection After Repair" after replacing the fuel pump.

Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>SFI SYSTEM (w/ Canister Pump Module)>INITIALIZATION