Home › Engine / Hybrid System › A25A-FXS (FUEL) › FUEL TANK (w/ Canister Pump Module) › 2017.09–2019.02
RM33C0E _51 Engine / Hybrid System _065421 A25A-FXS FUEL _0319776 FUEL TANK(w/ Canister Pump Module) A

A25A-FXS FUEL  FUEL TANK(w/ Canister Pump Module)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during fuel tank assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane departure alert system (w/ Steering Control) (Click here)
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Gas leak from exhaust system is repaired Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)

CAUTION:
·
A360563

Never perform work on fuel system components near any possible ignition sources.

·

Vaporized fuel could ignite, resulting in a serious accident.

·
A360564

Do not perform work on fuel system components without first disconnecting the cable from the negative (-) auxiliary battery terminal.

·

Sparks could cause vaporized fuel to ignite, resulting in a serious accident.

·
A344817

The fuel tank assembly is very heavy. Be sure to follow the procedure described in the repair manual, or the fuel tank assembly may fall off the engine lifter.



PROCEDURE

Hide 77020A 1.REMOVE FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY

Hide 2.DRAIN FUEL

Hide 17420 3.REMOVE CENTER EXHAUST PIPE ASSEMBLY

Hide 58399D 4.REMOVE NO. 2 FLOOR UNDER COVER (w/ Cover)

Hide 77641A 5.REMOVE NO. 1 FUEL TANK PROTECTOR

a.
A405280

Remove the 3 clips and No. 1 fuel tank protector from the fuel tank assembly.


Hide 77209F 6.DISCONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY

a.
A405263

Disconnect the fuel tank main tube sub-assembly from the fuel pipe.

Click hereEngine / Hybrid System>A25A-FXS (FUEL)>FUEL SYSTEM>PRECAUTION


Hide 77213E 7.DISCONNECT FUEL TANK TO FILLER PIPE HOSE

a.
A405269

Disconnect the fuel tank to filler pipe hose from the fuel tank assembly.

Click hereEngine / Hybrid System>A25A-FXS (FUEL)>FUEL SYSTEM>PRECAUTION


Hide 77100 8.REMOVE FUEL TANK ASSEMBLY

CAUTION:

The fuel tank assembly is very heavy. Be sure to follow the procedure described in the repair manual, or the fuel tank assembly may fall off the engine lifter.


a.
A405272

Support the fuel tank assembly using an engine lifter.

HINT:

Using height adjustment attachments and plate lift attachments, keep the fuel tank assembly horizontal.



b.
A405273

Remove the 4 bolts, No. 1 fuel tank band sub-assembly LH and No. 1 fuel tank band sub-assembly RH.


c.

Lower the engine lifter to remove the fuel tank assembly.

NOTICE:
·

Be careful not to drop the fuel tank assembly.

·

When removing the fuel tank assembly, tilt it slightly to prevent it from interfering with the surrounding parts.




Hide 77209F 9.REMOVE FUEL TANK MAIN TUBE SUB-ASSEMBLY

a.
A405275

Disengage the 2 clamps to remove the fuel tank main tube sub-assembly from the fuel tank assembly.


Hide 77651A 10.REMOVE NO. 1 FUEL TANK CUSHION

a.
A405278

Remove the 2 No. 1 fuel tank cushions from the fuel tank assembly.


Hide 77606 11.REMOVE NO. 1 FUEL TANK PROTECTOR SUB-ASSEMBLY

a.
A405281

Disengage the 2 claws and remove the No. 1 fuel tank protector sub-assembly from the fuel tank assembly.