Home › Engine / Hybrid System › A25A-FXS (FUEL) › FUEL MAIN VALVE (w/ Canister Pump Module) › 2017.09–2019.02
RM33C0E _51 Engine / Hybrid System _065421 A25A-FXS FUEL _0319780 FUEL MAIN VALVE(w/ Canister Pump Module) A

A25A-FXS FUEL  FUEL MAIN VALVE(w/ Canister Pump Module)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during fuel main valve assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane departure alert system (w/ Steering Control) (Click here)
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)

CAUTION:
·
A360563

Never perform work on fuel system components near any possible ignition sources.

·

Vaporized fuel could ignite, resulting in a serious accident.


·
A360564

Do not perform work on fuel system components without first disconnecting the cable from the negative (-) auxiliary battery terminal.

·

Sparks could cause vaporized fuel to ignite, resulting in a serious accident.



PROCEDURE

Hide 77020A 1.REMOVE FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY

Hide 23070 2.REMOVE FUEL MAIN VALVE ASSEMBLY

a.

for Type A:

i.
A406631

Remove the clip from the fuel suction tube with pump and gauge assembly.


ii.
A406632C01
0.708,0.813 1.813,0.813 true 0.542,0.708 0.854,0.865 0.313,0.156 10 false *a
*a Protective Tape


Using a screwdriver with its tip wrapped with protective tape, remove the fuel main valve assembly from the fuel suction tube with pump and gauge assembly.

NOTICE:
·

Pull out the fuel main valve assembly carefully because the O-rings are firmly installed between the fuel main valve assembly and fuel suction tube with pump and gauge assembly.

·

Do not damage the fuel suction tube with pump and gauge assembly.




iii.
A097616C10
0.875,0.969 0.875,0.5 false 0.667,0.5 1.833,0.5 1.833,0.5 1.833,0.729 false 0.469,0.427 0.75,0.604 0.281,0.177 10 false *1
*1 O-ring


Remove the 2 O-rings from the fuel main valve assembly.



b.

for Type B:

i.
A456276

Disengage the 2 claws and remove the fuel pressure regulator holder from the fuel suction tube with pump and gauge assembly.


ii.
A456277C01
1.813,0.458 2.417,0.458 true 1.594,0.385 1.781,0.552 0.188,0.167 10 true *a
*a Protective Tape


Using a screwdriver with its tip wrapped with protective tape, remove the fuel main valve assembly from the fuel suction tube with pump and gauge assembly.

NOTICE:
·

Pull out the fuel main valve assembly carefully because the O-ring is firmly installed between the fuel main valve assembly and fuel suction tube with pump and gauge assembly.


·

Do not damage the fuel suction tube with pump and gauge assembly.




iii.
A401697C02
1.021,0.417 1.125,0.417 1.125,0.417 1.229,0.823 false 1.563,0.688 1.698,0.292 1.698,0.292 1.813,0.292 false 0.958,1.719 1.073,1.719 1.073,1.719 1.135,1.375 false 1.865,0.208 2.177,0.365 0.313,0.156 10 false *1 0.854,0.313 1.167,0.469 0.313,0.156 10 false *a 0.792,1.625 1.104,1.781 0.313,0.156 10 false *b
*1 O-ring
*a Mesh
*b Mini-clip


Remove the O-ring from the fuel main valve assembly.

NOTICE:

Do not remove the mesh and mini-clip from the fuel main valve assembly.