Home › Engine / Hybrid System › A25A-FXS (EMISSION CONTROL) › CANISTER (w/ Canister Pump Module)
RM33C0E _51 Engine / Hybrid System _065422 A25A-FXS EMISSION CONTROL _0322967 CANISTER(w/ Canister Pump Module) A

A25A-FXS EMISSION CONTROL  CANISTER(w/ Canister Pump Module)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during canister (charcoal canister assembly) removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Gas leak from exhaust system is repaired Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)

PROCEDURE

Hide 48832A 1.REMOVE REAR NO. 1 STABILIZER BAR BRACKET

a.
A405777

Remove the 4 bolts and 2 rear No. 1 stabilizer bar brackets from the vehicle body.


Hide 77740 2.REMOVE CANISTER (CHARCOAL CANISTER ASSEMBLY)

a.
A472603C01
1.052,1.229 1.385,1.229 true 2.24,2.365 2.094,2.365 2.094,2.365 1.99,2.458 true 1.125,2.281 1.333,2.281 1.333,2.281 1.406,2.406 true 1.729,3 1.635,3.125 1.635,3.125 1.448,3.125 true 0.781,1.125 1,1.302 0.219,0.177 10 true *1 2.281,2.281 2.635,2.542 0.354,0.26 10 false *2 1.281,3.021 1.563,3.26 0.281,0.24 10 false *a 0.979,2.188 1.281,2.427 0.302,0.24 10 false *b
*1 Fuel Tank Vent Hose Sub-assembly
*2 Pipe (Leak Detection Pump Sub-assembly)
*a Tube Connector
*b O-ring
V100135

Pinch
V100136

Pull off


Disconnect the fuel tank vent hose sub-assembly from the leak detection pump sub-assembly.

NOTICE:
·

Remove any dirt or foreign matter on the tube connector before performing this work.

·

Perform this work by hand. Do not use any tools.

·

Do not forcibly bend, twist or turn the fuel tank vent hose sub-assembly.

·

Protect the disconnected parts by covering them with plastic bags after disconnecting the fuel tank vent hose sub-assembly.

·

If the tube connector and pipe (leak detection pump sub-assembly) are stuck, push and pull to release them.



i.

Push the fuel tank vent hose sub-assembly firmly toward the leak detection pump sub-assembly.


ii.

Pinch the tube connector as shown in the illustration.


iii.

Pull off the fuel tank vent hose sub-assembly from the pipe (leak detection pump sub-assembly).



b.
A405784

Disconnect the leak detection pump sub-assembly connector.


c.

Disconnect the fuel tank vent hose from the canister (charcoal canister assembly).

A405778C01
6.031,2.49 6.031,2 true 5.615,2.417 5.615,1.854 true 2.719,2.26 2.281,2.26 true 1.906,1.917 1.75,2.073 1.75,2.073 1.573,2.073 true 2.125,1.042 1.885,0.615 1.885,0.615 1.49,0.615 true 5.396,1.24 5.302,0.823 5.302,0.823 5.052,0.823 true 6.292,1.302 6.375,0.896 6.375,0.896 6.594,0.896 true 1.292,0.531 1.49,0.719 0.198,0.188 10 true *1 6.615,0.813 6.833,1.021 0.219,0.208 10 false *2 5.969,2.5 6.156,2.729 0.188,0.229 10 false *a 1.396,1.99 1.615,2.208 0.219,0.219 10 false *b 4.896,0.719 5.125,0.927 0.229,0.208 10 false *c 5.542,2.417 5.75,2.604 0.208,0.188 10 false *d 2.76,2.167 2.948,2.396 0.188,0.229 10 false *a
*1 Fuel Tank Vent Hose *2 Pipe (Canister (Charcoal Canister Assembly))
*a Retainer *b Tab
*c Tube Connector *d O-ring
V100135

Pinch
V100136

Pull


NOTICE:
·

Remove any dirt or foreign matter on the tube connector before performing this work.

·

Do not allow any scratches or foreign matter to get on the parts when disconnecting them as the tube connector has an O-ring that seals the pipe (canister (charcoal canister assembly)).

·

Perform this work by hand. Do not use any tools.

·

Do not forcibly bend, twist or turn the fuel tank vent hose.

·

Protect the disconnected parts by covering them with plastic bags after disconnecting the fuel tank vent hose.

·

If the tube connector and pipe (canister (charcoal canister assembly)) are stuck, push and pull to release them.



HINT:

Do not remove the retainer.


i.

Pinch the tabs of the retainer to disengage the lock claws and pull it down.


ii.

Pull off the fuel tank vent hose.



d.
A405780

Slide the clip and disconnect the purge line hose from the canister (charcoal canister assembly).


e.
A405781C01
0,0 0,0 false
V100135

Bolt
V100136

Clip


Remove the 2 bolts.


f.

Disengage the clip and disconnect the canister (charcoal canister assembly).


g.
A405782

Disengage the claw and remove the canister (charcoal canister assembly) from vehicle body as shown in the illustration.


h.
A405783

Remove the clip from the vehicle body.


Hide 77740R 3.REMOVE LEAK DETECTION PUMP SUB-ASSEMBLY

HINT:

Only perform this procedure when replacement of the leak detection pump sub-assembly is necessary.


a.

Before removing the leak detection pump sub-assembly, clean the charcoal canister sub-assembly by blowing air into it to ensure that the charcoal canister sub-assembly is free of foreign matter.

NOTICE:
·

Make sure to clean the charcoal canister sub-assembly using air only.

·

Do not use gasoline, thinners or solvents.




b.
A405785C01
1.302,1.542 1.552,1.917 1.552,1.917 1.792,1.917 true 1.823,1.823 2.021,2.021 0.198,0.198 10 true *a
*a Protective Tape


While disengaging the 2 claws as shown in the illustration, push the leak detection pump sub-assembly upwards using a screwdriver with its tip wrapped with protective tape to remove it.


c.

Check if the charcoal canister sub-assembly contains foreign matter such as mud or water.

i.
A405786

Visually check that the inside of the charcoal canister sub-assembly is free of foreign matter.


ii.

Hold the charcoal canister sub-assembly upside down to make sure that it is free of foreign matter.

If the charcoal canister sub-assembly contains foreign matter, replace the canister (charcoal canister assembly).