Home › Engine / Hybrid System › A25A-FXS (EMISSION CONTROL) › EGR VALVE › 2017.09–2020.08
RM33C0E _51 Engine / Hybrid System _065422 A25A-FXS EMISSION CONTROL _0322973 EGR VALVE A

A25A-FXS EMISSION CONTROL  EGR VALVE  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during EGR valve assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedures Effect/Inoperative Function when Necessary Procedure not Performed Link
·

Replacement of EGR valve assembly

·

Gas leak from exhaust system is repaired


Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)(w/ Canister Pump Module)
(Click here)(w/o Canister Pump Module)

NOTICE:

This procedure includes the removal of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

Hide 1.DRAIN ENGINE COOLANT (for Engine)

Hide 2.DISCONNECT ENGINE WIRE

a.
A405761C01
1.531,1.302 1.729,0.885 1.729,0.885 1.948,0.885 true 0.99,1.969 1.24,1.969 1.24,1.969 1.406,1.552 true 1.969,0.802 2.208,0.979 0.24,0.177 10 true *1 0.802,1.896 1.042,2.094 0.24,0.198 10 true *2
*1 No. 1 Fuel Vapor Feed Hose
*2 No. 2 Fuel Vapor Feed Hose


Disengage the 3 hose clamps and disconnect the No. 1 fuel vapor feed hose and No. 2 fuel vapor feed hose.


b.
A405762

Disconnect the EGR valve assembly connector.


c.

Remove the bolt.


d.

Disengage the 2 wire harness clamps and disconnect the engine wire.


Hide 25680 3.DISCONNECT EGR COOLER ASSEMBLY

a.
A405770

Remove the 2 bolts and disconnect the EGR cooler assembly from the EGR valve assembly.


b.

Remove the EGR valve gasket from the EGR valve assembly.


Hide 25601 4.REMOVE NO. 1 EGR PIPE SUB-ASSEMBLY

a.
A405763

Using an 8 mm socket wrench, remove the 4 bolts and No. 1 EGR pipe sub-assembly from the intake manifold and EGR valve assembly.


b.
A402226

Remove the EGR valve adapter gasket from the No. 1 EGR pipe sub-assembly.


c.
A402227

Remove the EGR inlet gasket from the intake manifold.


Hide 25620 5.REMOVE EGR VALVE ASSEMBLY

a.
A405764

Slide the clip and disconnect the No. 8 water by-pass hose from the EGR valve assembly.


b.
A405765C01
1.167,2.146 1.385,2.146 1.385,2.146 1.5,2.333 false 0.99,2.073 1.24,2.26 0.25,0.188 10 false *a
*a Retainer
V100135

Pinch
V100136

Pull
V100137

Pull off


w/ Water Hose Connector:

i.

Pinch the retainer of the water hose connector and then pull out the retainer to disengage the lock claws and pull off the No. 4 water by-pass hose from the EGR valve assembly.



c.
A430144

w/o Water Hose Connector:

i.

Slide the clip and disconnect the No. 4 water by-pass hose from the EGR valve assembly.



d.
A405767

for EGR Valve Bracket Connection Type:

i.

Using an 8 mm socket wrench, remove the bolt and disconnect the fuel pipe sub-assembly from the EGR valve bracket.



e.
A405768

Using the 8 mm socket wrench, remove the bolt.


f.
A406949C02
2.323,0.938 2.802,0.938 true 2.333,0.813 2.594,0.563 2.594,0.563 2.771,0.563 true 2.813,0.854 3.042,1.042 0.229,0.188 10 true *a 2.813,0.479 3.031,0.688 0.219,0.208 10 true *b
*a Pin
*b Hole


Remove the EGR valve assembly with the EGR valve bracket from the camshaft housing vertically.


g.
A402235

Using the 8 mm socket wrench, remove the bolt and EGR valve assembly from the EGR valve bracket.