Home › Engine / Hybrid System › A25A-FXS (INTAKE / EXHAUST) › EXHAUST PIPE › 2017.09–2019.10
RM33C0E _51 Engine / Hybrid System _065423 A25A-FXS INTAKE / EXHAUST _0322982 EXHAUST PIPE A

A25A-FXS INTAKE / EXHAUST  EXHAUST PIPE  INSTALLATION  


PROCEDURE

Hide 17408 1.INSTALL TAIL EXHAUST PIPE BAFFLE SUB-ASSEMBLY

HINT:
·

Perform this procedure only when replacement of the tail exhaust pipe baffle sub-assembly is necessary.

·

If the tail exhaust pipe baffle sub-assembly is removed, replace it with a new one.



a.
A472330C02
2.917,1.531 3.01,0.781 3.01,0.781 3.115,0.781 true 1.552,1.885 1.552,1.667 1.552,1.667 2.115,1.563 true 0.542,1.698 0.719,1.698 0.719,1.698 0.969,1.51 true 2.479,1.531 2.552,0.771 2.552,0.771 2.667,0.771 true 2.698,0.688 2.917,0.854 0.219,0.167 10 false *a 0.365,1.615 0.677,1.771 0.313,0.156 10 false *d 1.469,1.896 1.781,2.094 0.313,0.198 10 false *c 3.156,0.698 3.385,1.01 0.229,0.313 10 false *b
*a Protrusion (for position alignment)
*b Protrusion (for stopper)
*c Cutout
*d Wooden Block


Type A (w/ Tail Exhaust Pipe Baffle)

i.

Align the cutout of a new tail exhaust pipe baffle sub-assembly with the protrusion (for position alignment) of the tail exhaust pipe assembly as shown in the illustration.


ii.

Insert the tail exhaust pipe baffle sub-assembly to the position where it can be pressed in by hand.


iii.

Using a plastic hammer and wooden block, uniformly tap the tail exhaust pipe baffle sub-assembly onto the tail exhaust pipe assembly.

NOTICE:
·

Lightly tap the top and bottom of the tail exhaust pipe baffle sub-assembly so that the tail exhaust pipe baffle sub-assembly is pressed in without a tilt.

·

Press the tail exhaust pipe baffle sub-assembly in until the protrusion (for stopper) on the tail exhaust pipe baffle sub-assembly is fit into the cutout area of the tail exhaust pipe baffle sub-assembly.

·

Check that there is no looseness in the tail exhaust pipe baffle sub-assembly.





b.
A402315C01
0.229,1.229 0.469,1.229 0.469,1.229 0.656,1.646 true 0.792,1.656 1,1.958 1,1.958 1.479,1.958 true 0.063,1.146 0.26,1.313 0.198,0.167 10 true *a 1.479,1.875 1.667,2.063 0.188,0.188 10 false *b
*a Guide Line
*b Cutout


Type B

i.

Align the cutout of a new tail exhaust pipe baffle sub-assembly with the guide line of the tail exhaust pipe assembly as shown in the illustration.


ii.

Using a plastic hammer, uniformly tap the tail exhaust pipe baffle sub-assembly onto the tail exhaust pipe assembly.



Hide 17410 2.INSTALL FRONT EXHAUST PIPE ASSEMBLY (TWC: Rear Catalyst)

a.

Install a new gasket to the front exhaust pipe assembly (TWC: Rear Catalyst).


b.

Connect the front exhaust pipe assembly (TWC: Rear Catalyst) to the 2 exhaust pipe supports.


c.

Install the front exhaust pipe assembly (TWC: Rear Catalyst) to the exhaust manifold (TWC: Front Catalyst) with 2 new nuts.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


Hide 89467C 3.INSTALL AIR FUEL RATIO SENSOR (for Sensor 2)

Hide 17420 4.INSTALL CENTER EXHAUST PIPE ASSEMBLY

a.

Install a new gasket to the front exhaust pipe assembly (TWC: Rear Catalyst).


b.

Connect the center exhaust pipe assembly to the 2 exhaust pipe supports.


c.

Install the center exhaust pipe assembly to the front exhaust pipe assembly (TWC: Rear Catalyst) with 2 new bolts.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


Hide 17440 5.INSTALL TAIL EXHAUST PIPE ASSEMBLY LH

a.

Install a new gasket to the center exhaust pipe assembly.


b.

Connect the tail exhaust pipe assembly LH to the 2 exhaust pipe supports.


c.

Install the tail exhaust pipe assembly LH to the center exhaust pipe assembly with 2 new bolts.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


Hide 57523A 6.INSTALL CENTER FLOOR CROSSMEMBER BRACE

a.

Install the center floor crossmember brace to the vehicle body with the 4 bolts.

Torque:
15 N*m (153 kgf*cm, 11 ft.*lbf)


Hide 57533B 7.INSTALL FRONT CENTER FLOOR BRACE

a.

Install the front center floor brace to the vehicle body with the 4 bolts.

Torque:
15 N*m (153 kgf*cm, 11 ft.*lbf)


Hide 58166A 8.INSTALL FRONT FLOOR COVER LH (w/ Cover)

a.
A402309N01
2.219,0.083 2.354,0.24 0.135,0.156 10 true A 1.792,0.521 1.927,0.677 0.135,0.156 10 true A 1.833,1.448 1.969,1.604 0.135,0.156 10 true A 2.375,1.458 2.51,1.604 0.135,0.146 10 true A 2.75,0.417 2.896,0.583 0.146,0.167 10 true C 2.469,0.969 2.615,1.135 0.146,0.167 10 true C 1.177,0.021 1.323,0.188 0.146,0.167 10 true C 0.927,0.49 1.073,0.656 0.146,0.167 10 true C 0.719,1.021 0.865,1.188 0.146,0.167 10 true C 0.573,1.583 0.719,1.75 0.146,0.167 10 true B 1.906,1.823 2.052,1.99 0.146,0.167 10 true C

Install the front floor cover LH with the grommet (B) and 6 clips (C).


b.

Install the 3 bolts and 4 clips (A).

Torque:
Bolt : 7.5 N*m (76 kgf*cm, 66 in.*lbf)


Hide 58165C 9.INSTALL FRONT FLOOR COVER RH (w/ Cover)

a.
A402310N01
2.26,0.052 2.385,0.208 0.125,0.156 10 true A 1.917,0.521 2.042,0.677 0.125,0.156 10 true A 0.646,0.917 0.771,1.073 0.125,0.156 10 true A 1.24,0.896 1.365,1.052 0.125,0.156 10 true A 1.75,1.823 1.885,1.979 0.135,0.156 10 true B 2.031,1.479 2.167,1.635 0.135,0.156 10 true C 2.479,1.052 2.615,1.208 0.135,0.156 10 true C 2.677,0.052 2.813,0.208 0.135,0.156 10 true C 1.333,0.052 1.469,0.208 0.135,0.156 10 true C 1.094,0.469 1.229,0.625 0.135,0.156 10 true C 0.521,1.344 0.656,1.5 0.135,0.156 10 true C

Install the front floor cover RH with the grommet (B) and 6 clips (C).


b.

Install the 3 bolts and 4 clips (A).

Torque:
Bolt : 7.5 N*m (76 kgf*cm, 66 in.*lbf)


Hide 10.INSPECT FOR EXHAUST GAS LEAK

If gas is leaking, tighten the areas necessary to stop the leak. Replace damaged parts as necessary.

a.

Perform "Inspection After Repair" after repairing an exhaust gas leak.