Home › Engine / Hybrid System › A25A-FXS (ENGINE MECHANICAL) › CYLINDER BLOCK
RM33C0E _51 Engine / Hybrid System _065420 A25A-FXS ENGINE MECHANICAL _0324470 CYLINDER BLOCK A

A25A-FXS ENGINE MECHANICAL  CYLINDER BLOCK  REPLACEMENT  


PROCEDURE

Hide 11411A 1.REPLACE RING PIN

NOTICE:

It is not necessary to remove the ring pins unless they are being replaced.


a.

Remove the 12 ring pins.


b.

Using a plastic hammer, install 12 new ring pins.

A400543C01
0.604,0.156 0.917,0.354 0.313,0.198 10 false *a 0.635,1.698 0.948,1.896 0.313,0.198 10 false *b 3.74,1.031 4.052,1.229 0.313,0.198 10 false *d 4.271,1.573 4.583,1.771 0.313,0.198 10 false *e 6.354,0.875 6.667,1.073 0.313,0.198 10 false *c
*a Top Side *b Bottom Side
*c Protrusion Height *d 14 mm (0.551 in.)
*e 12 mm (0.472 in.) - -


Standard Protrusion Height:

5.0 to 7.0 mm (0.197 to 0.276 in.)



Hide 2.REPLACE STRAIGHT PIN

NOTICE:

It is not necessary to remove the straight pins unless they are being replaced.


a.

Remove the 10 straight pins.


b.

Using a plastic hammer, install 10 new straight pins.

A400544C01
0.896,0.198 1.208,0.396 0.313,0.198 10 false *a 0.948,3.427 1.26,3.625 0.313,0.198 10 false *b 3.531,0.167 3.844,0.365 0.313,0.198 10 false *c 3.573,1.813 3.885,2.01 0.313,0.198 10 false *d 3.698,3.458 4.01,3.656 0.313,0.198 10 false *e 2.698,3.583 2.854,3.781 0.156,0.198 10 false A 0.906,4.667 1.063,4.865 0.156,0.198 10 false A 1.104,1.604 1.26,1.802 0.156,0.198 10 false B 2.563,0.427 2.719,0.625 0.156,0.198 10 false B 3.802,0.646 3.958,0.844 0.156,0.198 10 false B 4.875,0.688 5.031,0.885 0.156,0.198 10 true B 4.021,1.781 4.177,1.979 0.156,0.198 10 false B 6.323,3.354 6.479,3.552 0.156,0.198 10 false B 5.896,5.031 6.052,5.229 0.156,0.198 10 false B 5.052,5 5.208,5.198 0.156,0.198 10 false B 1.667,5.177 1.823,5.375 0.156,0.198 10 false A 3.5,5.323 3.656,5.521 0.156,0.198 10 false B 2.146,5.813 2.458,6.01 0.313,0.198 10 false *g 1.656,6.469 1.969,6.667 0.313,0.198 10 false *h 3.885,5.771 4.198,5.969 0.313,0.198 10 false *i 3.49,6.354 3.802,6.552 0.313,0.198 10 false *j 5.813,5.646 6.125,5.844 0.313,0.198 10 false *f
*a Front Side *b Rear Side
*c LH Side *d Bottom Side
*e RH Side *f Protrusion Height
*g 22 mm (0.866 in.) *h 10 mm (0.394 in.)
*i 14 mm (0.551 in.) *j 6.0 mm (0.236 in.)


Standard Protrusion Height:
Straight Pin Specified Condition
(A) 11.0 to 13.0 mm (0.433 to 0.512 in.)
(B) 5.0 to 7.0 mm (0.197 to 0.276 in.)