Home › Engine / Hybrid System › A25A-FXS (ENGINE CONTROL) › CAMSHAFT TIMING CONTROL MOTOR
RM33C0E _51 Engine / Hybrid System _065419 A25A-FXS ENGINE CONTROL _0326943 CAMSHAFT TIMING CONTROL MOTOR A

A25A-FXS ENGINE CONTROL  CAMSHAFT TIMING CONTROL MOTOR  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:

This procedure includes the installation of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

Hide 13090E 1.INSTALL CAM TIMING CONTROL MOTOR O-RING

a.
A402350C01
0.958,0.313 1.188,0.313 1.188,0.313 1.563,0.865 true 0.771,0.219 1.083,0.375 0.313,0.156 10 false *a
*a Protrusion


Install a new cam timing control motor O-ring to the No. 2 timing gear cover assembly with the protrusion of the cam timing control motor O-ring oriented as shown in the illustration.


Hide 13090D 2.INSTALL CAM TIMING CONTROL MOTOR WITH EDU ASSEMBLY

HINT:

Perform "Inspection After Repair" after removing and installing, or replacing the cam timing control motor with EDU assembly.

w/ Canister Pump Module: Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>SFI SYSTEM (w/ Canister Pump Module)>INITIALIZATION

w/o Canister Pump Module: Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>SFI SYSTEM (w/o Canister Pump Module)>INITIALIZATION


a.
A401874C01
1.531,0.938 1.25,1.781 1.25,1.781 1.854,1.135 true 1.156,1.813 1.469,2.01 0.313,0.198 10 true *a
*a Cutout


Turn the cutout of the camshaft timing gear assembly eccentric shaft counterclockwise by hand, and set it to the maximum retard angle position.

HINT:
·

If a camshaft lobe is opening a valve, the eccentric shaft will be difficult to turn.

·

When the cutout of the camshaft timing gear assembly eccentric shaft cannot be turned any farther, it is set to the maximum retard angle.




b.
A401875C01
0.344,1.365 1.26,1.865 1.26,1.865 1.448,0.813 true 2,0.865 2.854,0.323 2.854,0.323 3.219,1.51 true 0.938,1.219 0.469,0.229 0.469,0.229 1.146,1.115 true 2.708,1.292 2.135,1.75 2.135,1.75 2.813,0.958 true 0.313,0.125 0.625,0.281 0.313,0.156 10 false *a 2.042,1.771 2.354,1.927 0.313,0.156 10 true *b 1.208,1.885 1.521,2.042 0.313,0.156 10 false *c 2.792,0.125 3.104,0.281 0.313,0.156 10 true *d
*a Joint
*b Cutout
*c Pin Hole
*d Knock Pin


Install the cam timing control motor with EDU assembly to the No. 2 timing gear cover assembly.

NOTICE:
·

When installing, align the joints of the cam timing control motor with EDU assembly with the cutouts of the camshaft timing gear assembly eccentric shaft.

·

Align the pin holes of the cam timing control motor with EDU assembly with the knock pins of the No. 2 timing gear cover assembly when installing the cam timing control motor with EDU assembly.

·

Make sure the contact surface of the cam timing control motor with EDU assembly (the surface that contacts the No. 2 timing gear cover assembly) is free of foreign matter.

·

When installing the cam timing control motor with EDU assembly, do not use excessive force.

·

If the cam timing control motor with EDU assembly has been struck or dropped, replace it.

·

Do not disassemble the cam timing control motor with EDU assembly. If disassembled, replace it.




c.

Install the 3 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


d.

Connect the cam timing control motor with EDU assembly connector.


Hide 3.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 64718C 4.INSTALL LUGGAGE TRIM SERVICE HOLE COVER

Hide 5.INSPECT FOR ENGINE OIL LEAK

Hide 12601B 6.INSTALL NO. 1 ENGINE COVER SUB-ASSEMBLY

Hide 7.PERFORM INITIALIZATION

a.

Perform "Inspection After Repair" after removing and installing, or replacing the cam timing control motor with EDU assembly.

w/ Canister Pump Module: Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>SFI SYSTEM (w/ Canister Pump Module)>INITIALIZATION

w/o Canister Pump Module: Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>SFI SYSTEM (w/o Canister Pump Module)>INITIALIZATION