Home › Vehicle Exterior › SLIDING ROOF / CONVERTIBLE › SLIDING ROOF HOUSING (for Panoramic Moon Roof)
RM33C0E _59 Vehicle Exterior _065468 SLIDING ROOF / CONVERTIBLE _0328286 SLIDING ROOF HOUSING(for Panoramic Moon Roof) A

SLIDING ROOF / CONVERTIBLE  SLIDING ROOF HOUSING(for Panoramic Moon Roof)  REASSEMBLY  


PROCEDURE

Hide 63306 1.INSTALL SUNSHADE TRIM SUB-ASSEMBLY

a.
B481854C01
0.354,1.854 0.354,1.625 true 1.594,1.208 1.208,0.823 true 2.01,2.208 2.313,2.469 0.302,0.26 12 true *B 0.26,1.875 0.573,2.073 0.313,0.198 10 false *b 0.573,0.094 0.885,0.417 0.313,0.323 12 false *A 1.625,1.115 1.938,1.313 0.313,0.198 10 false *a
*A RH Side
*B LH Side
*a Retractor Cap
*b Portion A
V113147

Install in this Direction (1)
V113148

Install in this Direction (2)


Install the sunshade trim sub-assembly as shown in the illustration.

NOTICE:

To prevent the sunshade trim sub-assembly from being damaged, fully push in the RH side retractor cap when installing the sunshade trim sub-assembly.


HINT:
·

Connect the LH side first.

·

Set the portion (A) within the area shown in the illustration when installing the sunshade trim sub-assembly.




b.
B481855C02
0,0 0,0 false
V113147

Install in this Direction


Insert the sliding roof sunshade runner into the sunshade trim sub-assembly as shown in the illustration.

HINT:

Use the same procedure for the RH side and LH side.



c.
B481856C01
1.333,0.802 2.25,0.26 true 2.281,0.156 2.594,0.354 0.313,0.198 10 false *1
*1 Sliding Roof Guide Rail Sub-assembly RH
V113147

Install in this Direction


Slide the sliding roof sunshade runner and sunshade trim sub-assembly as shown in the illustration to install them to the sliding roof guide rail sub-assembly RH.

HINT:

Use the same procedure for the RH side and LH side.



d.
B481857C01
0.656,1.531 0.656,1.021 true 0.563,1.552 0.875,1.75 0.313,0.198 10 false *a
*a Portion A
V113147

Install in this Direction


Move the portion (A) as shown in the illustration to engage the claw.

HINT:

Use the same procedure for the RH side and LH side.



e.
B481858C01
0,0 0,0 false
V113147

Install in this Direction


Engage the claw to install the sliding roof sunshade guide RH as shown in the illustration.

HINT:

Use the same procedure for the RH side and LH side.



Hide 63202H 2.INSTALL SLIDE ROOF RAIL SUB-ASSEMBLY

a.

Install the slide roof rail sub-assembly with the 42 nuts.

B481865C01
0,0 0,0 false
V100135

Nut (A)
V100136

Nut (B)


Torque:
Nut (A) : 6.2 N*m (63 kgf*cm, 55 in.*lbf)
Nut (B) : 9.4 N*m (96 kgf*cm, 83 in.*lbf)


Hide 63231C 3.INSTALL ROOM LIGHT BRACKET

a.
B481848

Install the room light bracket with the 2 nuts.

Torque:
6.2 N*m (63 kgf*cm, 55 in.*lbf)


Hide 63219A 4.INSTALL REAR SLIDING ROOF GARNISH

a.

Clean the sliding roof housing panel.

i.

Using a heat light, heat the sliding roof housing panel.

Heating Temperature
Item Temperature
Sliding Roof Housing Panel 40 to 60°C (104 to 140°F)

CAUTION:
E306500C23
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts, touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat the sliding roof housing panel excessively.



ii.

Remove the double-sided tape from the sliding roof housing panel.


iii.

Clean off any tape adhesive residue with cleaner.



b.

Coat the installation area of the sliding roof housing panel with primer.


c.

Remove the release paper from a new rear sliding roof garnish.

HINT:

After removing the release paper, keep the exposed adhesive free from foreign matter.



d.

Engage the 3 guides and 3 fasteners to install the rear sliding roof garnish.

B481847C01
3.719,0.865 3.958,0.865 true 3.333,1.021 3.573,1.021 true 3.74,1.385 3.979,1.385 true 3.76,1.75 4,1.75 true 3.344,1.573 3.583,1.573 true 3.344,1.292 3.583,1.292 true 3.344,0.667 3.583,0.667 true 3.75,0.542 3.99,0.542 true 3.729,0.677 3.969,0.677 true 3.76,1.969 4,1.969 true 3.354,1.979 3.594,1.979 true 3.76,2.146 4,2.146 true 3.146,0.917 3.458,1.073 0.313,0.156 10 false *a 3.979,0.781 4.292,0.938 0.313,0.156 10 false *b 4.01,1.292 4.323,1.448 0.313,0.156 10 false *b 3.146,1.188 3.458,1.344 0.313,0.156 10 false *a 3.135,1.469 3.448,1.625 0.313,0.156 10 false *a 4.021,1.656 4.333,1.813 0.313,0.156 10 false *b 3.146,0.594 3.458,0.75 0.313,0.156 10 false *c 4.021,0.438 4.333,0.594 0.313,0.156 10 false *c 4,0.594 4.313,0.75 0.313,0.156 10 false *c 4.021,1.885 4.333,2.042 0.313,0.156 10 false *c 3.167,1.885 3.479,2.042 0.313,0.156 10 false *c 4.021,2.063 4.333,2.219 0.313,0.156 10 false *c
*a Fastener *b Guide
*c Double-sided Tape - -



Hide 63260K 5.INSTALL SLIDING ROOF DRIVE GEAR ASSEMBLY (for Roof Sunshade)

a.

Apply MP grease to the gear of the sliding roof drive gear assembly.


b.
B481846

Install the sliding roof drive gear assembly with the 2 bolts.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


Hide 63260J 6.INSTALL SLIDING ROOF DRIVE GEAR ASSEMBLY (for Sliding Roof Glass)

a.

Apply MP grease to the gear of the sliding roof drive gear assembly.


b.
B481845

Install the sliding roof drive gear assembly with the 2 bolts.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


Hide 63209 7.INSTALL ROOF WIND DEFLECTOR PANEL SUB-ASSEMBLY

a.

Engage the 4 pins as shown in the illustration.

B481866


b.

Engage the 3 claws to install the roof wind deflector panel sub-assembly.


Hide 82172 8.INSTALL NO. 2 ROOF WIRE

a.

Engage the 16 clamps to install the No. 2 roof wire.

B481844


b.

Connect the 3 connectors.


Hide 63218M 9.INSTALL NO. 1 SLIDING ROOF SIDE GARNISH LH

a.

Clean the sliding roof housing panel.

i.

Using a heat light, heat the sliding roof housing panel.

Heating Temperature
Item Temperature
Sliding Roof Housing Panel 40 to 60°C (104 to 140°F)

CAUTION:
E306500C23
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts, touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat the sliding roof housing panel excessively.



ii.

Remove the double-sided tape from the sliding roof housing panel.


iii.

Clean off any tape adhesive residue with cleaner.



b.

Coat the installation area of the sliding roof housing panel with primer.


c.

Remove the release paper from a new No. 1 sliding roof side garnish LH.

HINT:

After removing the release paper, keep the exposed adhesive free from foreign matter.



d.

Engage the 2 guides and 28 claws to install the No. 1 sliding roof side garnish LH.

B481860C01
0,0 0,0 false
V100155

Double-sided Tape - -



Hide 63217K 10.INSTALL NO. 1 SLIDING ROOF SIDE GARNISH RH

HINT:

Use the same procedure as for the LH side.