Home › Vehicle Exterior › SLIDING ROOF / CONVERTIBLE › SLIDING ROOF HOUSING(for Moon Roof)
RM33C0E _59 Vehicle Exterior _065468 SLIDING ROOF / CONVERTIBLE _0328287 SLIDING ROOF HOUSING(for Moon Roof) A

SLIDING ROOF / CONVERTIBLE  SLIDING ROOF HOUSING(for Moon Roof)  INSTALLATION  


PROCEDURE

Hide 1.INSTALL SLIDING ROOF HOUSING ASSEMBLY

a.

Loosen the 4 bolts of the brackets of the sliding roof housing assembly.


b.

Temporarily install the sliding roof housing assembly with the 6 nuts and 8 bolts.

B468947N01
2.979,1.302 3.135,1.5 0.156,0.198 10 true 1 4.729,2.292 4.885,2.49 0.156,0.198 10 true 2


c.

Tighten the 2 nuts.

HINT:

Tighten the 2 nuts in the order shown in the illustration.


Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


d.

Tighten the 4 nuts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


e.

Tighten the 12 bolts to install the sliding roof housing assembly.

B468965C01
0,0 0,0 false
V100135

Bolt (A)
V100136

Bolt (B)
V100137

Bolt (C) - -


HINT:
·

The brackets can be installed in any order.

·

Tighten the bolts in the order of (A), (B) and then (C).



Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 2.CONNECT SLIDING ROOF DRAIN HOSE

HINT:

Use the same procedure for all of the sliding roof drain hoses.


a.
B468966C01
2.635,0.531 2.823,0.292 true 2.75,0.719 2.896,0.865 true 2.802,0.177 3.115,0.333 0.313,0.156 10 false *a 2.917,0.792 3.229,0.948 0.313,0.156 10 false *b
*a Clamp
*b Marking


for Clamp Type:

i.

Connect the sliding roof drain hose.

HINT:

Slide the hose to the base of the drain pipe.



ii.

Engage the claw to secure the sliding roof drain hose.

HINT:

Make sure that the clamp is on the marking or between the marking and hose end.




b.
B468967C01
2.802,0.396 3,0.281 true 2.833,0.656 3.021,0.917 true 3,0.177 3.313,0.333 0.313,0.156 10 false *a 2.948,0.927 3.146,1.125 0.198,0.198 10 true *b
*a Clip
*b Marking
V100135

Outside
V100136

Front Side


for Clip Type:

i.

Expand the clip to connect the sliding roof drain hose.

HINT:

Slide the hose to the base of the drain pipe.



ii.

Release the clip to secure the sliding roof drain hose.

NOTICE:

The clip must face toward the outside of the vehicle and also be above the lower surface of the sliding roof housing sub-assembly when installing the drain hoses.


HINT:

Make sure that the clip is on the marking or between the marking and hose end.




Hide 63251H 3.INSTALL SLIDING ROOF WEATHERSTRIP

a.

Install the sliding roof weatherstrip.

B461629C01
4,0.833 7,3.417 3,2.583 6.333,2.708 6.646,2.365 true 2.063,3.604 2.063,3.396 false 3.594,0.833 3.208,0.833 true 0.917,0.833 0.531,0.833 true 3.49,0.667 3.302,0.74 true 0.813,0.74 0.625,0.646 true 4.813,2.625 5.083,2.281 false 1.979,3.604 2.292,3.76 0.313,0.156 10 false *a 0.458,0.521 0.771,0.677 0.313,0.156 10 false *b 3.625,0.75 3.938,0.906 0.313,0.156 10 false *c 4.083,0.917 4.396,1.073 0.313,0.156 10 false *d 4.083,2.167 4.396,2.323 0.313,0.156 10 false *e 5.104,2.177 5.417,2.333 0.313,0.156 10 false *f 6.646,2.24 6.938,2.448 0.292,0.208 10 false *g 0.375,0.729 0.688,0.885 0.313,0.156 10 false *c 3.5,0.552 3.813,0.708 0.313,0.156 10 false *b
*a Joint *b Alignment Mark (Blue)
*c Middle Mark *d Correct
*e Incorrect *f Pinched
*g Gap (raised, wavy, etc.) - -
V100136

Front Side - -


i.

Position the joint of the sliding roof weatherstrip on the rear side.


ii.

Align the alignment marks (Blue) on the sliding roof weatherstrip with the middle marks on the front corners of the sliding roof panel sub-assembly and install the sliding roof weatherstrip.

HINT:

Make sure to install the lip of the sliding roof weatherstrip securely.




Hide 63201G 4.INSTALL SLIDING ROOF GLASS SUB-ASSEMBLY

a.

Using a T25 "TORX" socket wrench, temporarily install the sliding roof glass sub-assembly with the 4 screws.


b.

Perform a level check.

B468968N01
1.813,1.542 1.99,1.708 0.177,0.167 10 true A 1.573,1.542 1.75,1.708 0.177,0.167 10 true A 2.156,2.083 2.333,2.25 0.177,0.167 10 true B 2.406,2.083 2.583,2.25 0.177,0.167 10 true B 2.25,1.104 2.427,1.271 0.177,0.167 10 true C 2.25,1.333 2.427,1.5 0.177,0.167 10 true C 1.896,2.333 2.063,2.521 0.167,0.188 10 true D 2.031,2.552 2.198,2.74 0.167,0.188 10 true D 5.74,0.948 6.052,1.146 0.313,0.198 10 false a

i.

Check the difference in level "a" between the roof panel and the upper surface of the sliding roof weatherstrip when the sliding roof glass sub-assembly is fully closed.

HINT:

"+" represents the condition that the glass is above the panel level. "-" represents the condition that the glass is below the panel level.


Standard:
Area Measurement Area Measurement
A - A -2.0 to 1.0 mm (-0.0787 to 0.0394 in.) B - B -1.0 to 2.0 mm (-0.0394 to 0.0787 in.)
C - C -1.5 to 1.5 mm (-0.0591 to 0.0591 in.) D - D -1.0 to 1.5 mm (-0.0394 to 0.0591 in.)




c.
B468969C01
1.844,1.479 2.156,1.635 0.313,0.156 10 false *a
*a Even


Perform a gap check.

i.

Check the gap between the roof panel and sliding roof glass sub-assembly.

NOTICE:

The gap must be even all around.




d.

After adjusting the sliding roof glass sub-assembly, using a T25 "TORX" socket wrench, install the sliding roof glass sub-assembly with the 4 screws.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


Hide 5.CHECK FOR WATER LEAK

a.

After adjusting the sliding roof glass sub-assembly, check for water leakage into the vehicle interior.


b.

If there are any leaks, readjust the sliding roof glass sub-assembly.


Hide 62180A 6.INSTALL CURTAIN SHIELD AIRBAG ASSEMBLY LH

Hide 62170A 7.INSTALL CURTAIN SHIELD AIRBAG ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 63218G 8.INSTALL SLIDING ROOF SIDE GARNISH LH

a.

Engage the 4 claws to install a new sliding roof side garnish LH.


Hide 63217G 9.INSTALL SLIDING ROOF SIDE GARNISH RH

HINT:

Use the same procedure as for the LH side.