Home › Vehicle Exterior › SLIDING ROOF / CONVERTIBLE › SLIDING ROOF HOUSING(for Moon Roof)
RM33C0E _59 Vehicle Exterior _065468 SLIDING ROOF / CONVERTIBLE _0328287 SLIDING ROOF HOUSING(for Moon Roof) A

SLIDING ROOF / CONVERTIBLE  SLIDING ROOF HOUSING(for Moon Roof)  DISASSEMBLY  


PROCEDURE

Hide 63260A 1.REMOVE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY

a.
B468948C01
0,0 0,0 false
V113147

Remove in this Direction


Remove the bolt.


b.

Disengage the claw and guide as shown in the illustration to remove the map light bracket.


c.
B468949

Remove the 2 bolts and sliding roof drive gear sub-assembly.


Hide 63306 2.REMOVE SUNSHADE TRIM SUB-ASSEMBLY

a.
B468950C01
0,0 0,0 false
V113147

Remove in this Direction (1)
V113148

Remove in this Direction (2)


Remove the screw.

HINT:

Use the same procedure for the RH side.



b.

Move the sliding roof piece sub-assembly LH in the direction indicated by the arrow (1) shown in the illustration to disengage the guide.

HINT:

Use the same procedure for the RH side.



c.

Move the sliding roof piece sub-assembly LH in the direction indicated by the arrow (2) shown in the illustration to disengage the 2 claws and remove the sliding roof piece sub-assembly LH.

HINT:

Use the same procedure for the RH side.



d.
B468951C01
0,0 0,0 false
V113147

Remove in this Direction


Remove the rear sliding roof sunshade stopper as shown in the illustration.

HINT:

Use the same procedure for the RH side.



e.
B468952C01
0,0 0,0 false
V113147

Remove in this Direction


Slide and remove the sunshade trim sub-assembly as shown in the illustration.


Hide 63205A 3.REMOVE SLIDING ROOF DRIVE CABLE SUB-ASSEMBLY

NOTICE:

Do not disassemble the sliding roof drive cable sub-assembly except when replacing it.


a.

Using a screwdriver, disengage the 2 claws as shown in the illustration.

B468953C01
0.406,0.531 0.604,0.531 true 6.552,1.292 6.75,1.292 true 0.198,0.438 0.396,0.625 0.198,0.188 10 true *a 6.771,1.188 6.969,1.375 0.198,0.188 10 true *a
*a Protective Tape - -
V113147

Remove in this Direction - -


HINT:

Tape the screwdriver tip before use.



b.
B468954C01
0,0 0,0 false
V113147

Remove in this Direction


Slide and remove the rear roof drip channel as shown in the illustration.


c.
B468955C01
0,0 0,0 false
V113146

Hold Position


Hold down the roof wind deflector panel sub-assembly.


d.
B468956C01
1.75,4.073 1.75,3.677 true 1.688,4.083 2,4.24 0.313,0.156 10 false *a
*a Protective Tape
V113146

Push Position
V113147

Remove in this Direction


Using a screwdriver, slide the sliding roof drive cable LH as shown in the illustration to remove it.

HINT:
·

Tape the screwdriver tip before use.

·

Use the same procedure for the RH side.




Hide 63209 4.REMOVE ROOF WIND DEFLECTOR PANEL SUB-ASSEMBLY

a.
B468972C01
0.729,0.573 1.031,0.333 true 0.313,0.698 0.188,0.604 true 2.427,1.125 2.677,0.99 true 2.458,1.448 2.708,1.313 true 1.052,0.229 1.365,0.385 0.313,0.156 10 false *a 0.021,0.479 0.229,0.677 0.208,0.198 10 false *b 2.26,1.021 2.573,1.177 0.313,0.156 10 false *a 2.302,1.354 2.51,1.552 0.208,0.198 10 false *b
*a Spring
*b Guide
V113147

Remove in this Direction (1)
V113148

Remove in this Direction (2)


Pull each spring in the direction indicated by the arrow (1) shown in the illustration to disengage the 2 springs.


b.

Pull the roof wind deflector panel sub-assembly in the direction indicated by the arrow (2) shown in the illustration to disengage the 2 guides and remove it.