Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM
RM33C0E _54 Brake _065442 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0328411 ELECTRONICALLY CONTROLLED BRAKE SYSTEM U

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  DATA LIST / ACTIVE TEST  


DATA LIST


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


a.

Warm up the engine.


b.

Turn the power switch off.


c.

Connect the GTS to the DLC3.


d.

Turn the power switch on (IG).


e.

Turn the GTS on.


f.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.


g.

According to the display on the GTS, read the Data List.

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
ABS Warning Light ABS warning light ON or OFF ON: Warning light on
OFF: Warning light off
-
Brake Warning Light Brake warning light / red (malfunction) ON or OFF ON: Warning light on
OFF: Warning light off
-
ECB Warning Light Brake warning light / yellow (minor malfunction) ON or OFF ON: Warning light on
OFF: Warning light off
ECB: Electronically Controlled Brake System
Buzzer Meter buzzer ON or OFF ON: Buzzer on
OFF: Buzzer off
-
Stop Light SW Stop light switch assembly ON or OFF ON: Brake pedal depressed
OFF: Brake pedal released
-
Parking Brake SW Parking brake switch assembly ON or OFF ON: Parking brake applied
OFF: Parking brake released
-
TRC(TRAC)/VSC OFF SW VSC OFF switch ON or OFF ON: Switch on
OFF: Switch off
-
Reservoir Warning SW Brake fluid level warning switch ON or OFF ON: Reservoir level low
OFF: Reservoir level normal
-
Main Idle SW Main idle switch ON or OFF ON: Accelerator pedal released
OFF: Accelerator pedal depressed
-
Shift Lever Position Shift position information Fail, 1st, 2nd, 3rd, 4th, 5th, 6th/B, D/M, P,N or R Actual shift position -
Inspection Mode Inspection mode Other or Inspect Other: Normal mode
Inspect: Inspection mode
-
Stroke Sensor Brake pedal stroke sensor assembly Min.: 0.00 V, Max.: 5.00 V Brake pedal released: 0.65 to 1.35 V Reading increases when brake pedal is depressed
Voltage of Stroke Sensor Voltage of brake pedal stroke sensor assembly Min.: -2.50 V, Max.: 2.49 V - -
Stroke Sensor2 Brake pedal stroke sensor assembly 2 Min.: 0.00 V, Max.: 5.00 V Brake pedal released: 3.65 to 4.35 V Reading decreases when brake pedal is depressed
Voltage of Stroke Sensor2 Voltage of brake pedal stroke sensor assembly 2 Min.: -2.50 V, Max.: 2.49 V - -
Deceleration Sensor Acceleration sensor 1 Min.: -18.525 m/s2, Max.: 18.387 m/s2 - During deceleration/acceleration: Changes continuously
Zero Point of Decele Memorized zero value Min.: -25.10 m/s2, Max.: 24.90 m/s2 - -
Deceleration Sensor2 Acceleration sensor 2 Min.: -18.525 m/s2, Max.: 18.387 m/s2 - During deceleration/acceleration: Changes continuously
Zero Point of Decele2 Memorized zero value Min.: -25.10 m/s2, Max.: 24.90 m/s2 - -
Yaw Rate Sensor Yaw rate sensor 1 Min.: -128 degrees/s, Max.: 127 degrees/s Vehicle stationary: 0 degrees/s
Turning right: -128 to 0 degrees/s
Turning left: 0 to 127 degrees/s
-
Zero Point of Yaw Rate Memorized zero value Min.: -128 degrees, Max.: 127 degrees - After completing zero point calibration: 0 degrees
Yaw Rate Sensor2 Yaw rate sensor 2 Min.: -128 degrees/s, Max.: 127 degrees/s Vehicle stationary: 0 degrees/s
Turning right: -128 to 0 degrees/s
Turning left: 0 to 127 degrees/s
-
Steering Angle Sensor Steering angle sensor Min.: -3276.8 degrees, Max.: 3276.7 degrees Turning left: Increases
Turning right: Decreases
-
Zero Point of Steering Angle Memorized zero value Min.: -3276.8 degrees, Max.: 3276.7 degrees - After clearing zero point calibration: 0 degrees
Lateral G Lateral G Min.: -25.10 m/s2, Max.: 24.90 m/s2 - During turning: Changes in proportion with lateral acceleration
Forward and Rearward G Forward and backward G Min.: -25.10 m/s2, Max.: 24.90 m/s2 - During acceleration/deceleration: Changes in proportion with acceleration
Yaw Rate Value Yaw rate value Min.: -128 degrees/s, Max.: 127 degrees/s - During turning: Changes in proportion with yaw
Steering Angle Value Steering angle value Min.: -3276.8 degrees, Max.: 3276.7 degrees - During steering operation: Changes in proportion with steering wheel rotation
Stop Light Relay Stop light control relay (Stop light switch assembly)
(STP2 terminal input)
ON or OFF ON: Brake pedal depressed
OFF: Brake pedal released
-
Slip Indicator Light Slip indicator light ON or OFF ON: Indicator light on
OFF: Indicator light off
-
FR Wheel Speed Front speed sensor RH Min.: 0 km/h (0 mph), Max.: 326.4 km/h (203 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
FL Wheel Speed Front speed sensor LH Min.: 0 km/h (0 mph), Max.: 326.4 km/h (203 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
RR Wheel Speed Rear speed sensor RH Min.: 0 km/h (0 mph), Max.: 326.4 km/h (203 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
RL Wheel Speed Rear speed sensor LH Min.: 0 km/h (0 mph), Max.: 326.4 km/h (203 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
Vehicle Speed Maximum wheel speed sensor Min.: 0 km/h (0 mph), Max.: 326.4 km/h (203 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
FR Wheel Acceleration Front wheel RH acceleration Min.: -200.84 m/s2, Max.: 199.27 m/s2 - During deceleration/acceleration: Changes continuously
FL Wheel Acceleration Front wheel LH acceleration Min.: -200.84 m/s2, Max.: 199.27 m/s2 - During deceleration/acceleration: Changes continuously
RR Wheel Acceleration Rear wheel RH acceleration Min.: -200.84 m/s2, Max.: 199.27 m/s2 - During deceleration/acceleration: Changes continuously
RL Wheel Acceleration Rear wheel LH acceleration Min.: -200.84 m/s2, Max.: 199.27 m/s2 - During deceleration/acceleration: Changes continuously
Stop Light Relay Output Stop light control relay (Stop light switch assembly)
(STPO terminal output)
ON or OFF ON: Relay output on
OFF: Relay output off
-
FR Wheel ABS Ctrl Status Front wheel RH ABS control status ON or OFF ON: During control -
FL Wheel ABS Ctrl Status Front wheel LH ABS control status ON or OFF ON: During control -
RR Wheel ABS Ctrl Status Rear wheel RH ABS control status ON or OFF ON: During control -
RL Wheel ABS Ctrl Status Rear wheel LH ABS control status ON or OFF ON: During control -
BA Ctrl Status BA control status ON or OFF ON: During control -
PBA Ctrl Status PBA control status ON or OFF ON: During control w/ Pre-collision System
TRC(TRAC) Ctrl Status TRC control status ON or OFF ON: During control -
TRC(TRAC) Engine Ctrl Status TRC engine control status ON or OFF ON: During control -
TRC(TRAC) Brake Ctrl Status TRC brake control status ON or OFF ON: During control -
FR Wheel VSC Ctrl Status Front wheel RH VSC control status ON or OFF ON: During control -
FL Wheel VSC Ctrl Status Front wheel LH VSC control status ON or OFF ON: During control -
RR Wheel VSC Ctrl Status Rear wheel RH VSC control status ON or OFF ON: During control -
RL Wheel VSC Ctrl Status Rear wheel LH VSC control status ON or OFF ON: During control -
Accelerator Opening Angle % Percentage of accelerator pedal opening angle Min.: 0.0%, Max.: 127.5% Accelerator pedal released: 0.0% During accelerator pedal operation: Changes in proportion with the pedal movement
Regenerative Cooperation Regenerative cooperation ON or OFF ON: Operating
OFF: Not operating
-
FR Regenerative Request FR regenerative request torque Min.: 0 Nm, Max.: 1048560 Nm - Changes according to brake pedal force
(When depressing the brake pedal lightly after reaching 30 km/h (19 mph) or more, avoiding sudden braking.)
FR Regenerative Operation FR regenerative operation torque Min.: 0 Nm, Max.: 1048560 Nm - Changes according to brake pedal force
(When depressing the brake pedal lightly after reaching 30 km/h (19 mph) or more, avoiding sudden braking.)
Solenoid Relay ABS solenoid relay operation request ON or OFF ON: Power switch on (IG) (During initial check)
OFF: Power switch off
-
ECB Motor Relay Motor relay 1 operation request ON or OFF ON: Relay on
OFF: Relay off
ECB: Electronically Controlled Brake System
ECB Motor Relay2 Motor relay 2 operation request ON or OFF ON: Relay on
OFF: Relay off
ECB: Electronically Controlled Brake System
ECB Main Relay Main relay operation request ON or OFF ON: Relay on
OFF: Relay off
ECB: Electronically Controlled Brake System
ABS Solenoid (SFRH) Holding solenoid valve (FRH) ON or OFF ON: Operating
OFF: Not operating
-
ABS Solenoid (SFRR) Reduction solenoid valve (FRR) ON or OFF ON: Operating
OFF: Not operating
-
ABS Solenoid (SFLH) Holding solenoid valve (FLH) ON or OFF ON: Operating
OFF: Not operating
-
ABS Solenoid (SFLR) Reduction solenoid valve (FLR) ON or OFF ON: Operating
OFF: Not operating
-
ABS Solenoid (SRRH) Holding solenoid valve (RRH) ON or OFF ON: Operating
OFF: Not operating
-
ABS Solenoid (SRRR) Reduction solenoid valve (RRR) ON or OFF ON: Operating
OFF: Not operating
-
ABS Solenoid (SRLH) Holding solenoid valve (RLH) ON or OFF ON: Operating
OFF: Not operating
-
ABS Solenoid (SRLR) Reduction solenoid valve (RLR) ON or OFF ON: Operating
OFF: Not operating
-
FR Speed Open Front speed sensor RH open detection Error or Normal Error: Momentary interruption
Normal: Normal
-
FL Speed Open Front speed sensor LH open detection Error or Normal Error: Momentary interruption
Normal: Normal
-
RR Speed Open Rear speed sensor RH open detection Error or Normal Error: Momentary interruption
Normal: Normal
-
RL Speed Open Rear speed sensor LH open detection Error or Normal Error: Momentary interruption
Normal: Normal
-
Yaw Rate Open Yaw rate sensor open detection Error or Normal Error: Momentary interruption
Normal: Normal
-
Deceleration Open Acceleration sensor open detection Error or Normal Error: Momentary interruption
Normal: Normal
-
Steering Open Steering angle sensor open detection Error or Normal Error: Momentary interruption
Normal: Normal
-
Stroke Open Brake pedal stroke sensor assembly open detection Error or Normal Error: Momentary interruption
Normal: Normal
-
Stroke2 Open Brake pedal stroke sensor assembly 2 open detection Error or Normal Error: Momentary interruption
Normal: Normal
-
Accumulator Open Accumulator pressure sensor open detection Error or Normal Error: Momentary interruption
Normal: Normal
-
HV Communication Open Hybrid vehicle communication open detection Error or Normal Error: Momentary interruption
Normal: Normal
-
VCM1 Voltage Value VCM1 voltage value Min.: 0.00 V, Max.: 10.00 V 6.29 to 7.64 V -
VCM2 Voltage Value VCM2 voltage value Min.: 0.00 V, Max.: 10.00 V 6.29 to 7.64 V -
IG1 Voltage Value IG1 voltage value Min.: 0.00 V, Max.: 20.00 V - Changes in proportion to auxiliary battery voltage
IG2 Voltage Value IG2 voltage value Min.: 0.00 V, Max.: 20.00 V - Changes in proportion to auxiliary battery voltage
BS1 Voltage Value BS1 voltage value Min.: 0.00 V, Max.: 20.00 V - Changes in proportion to auxiliary battery voltage
BS2 Voltage Value BS2 voltage value Min.: 0.00 V, Max.: 20.00 V - Changes in proportion to auxiliary battery voltage
VM1 Voltage Value VM1 voltage value Min.: 0.00 V, Max.: 20.00 V - Changes in proportion to auxiliary battery voltage
VM2 Voltage Value VM2 voltage value Min.: 0.00 V, Max.: 20.00 V - Changes in proportion to auxiliary battery voltage
MT Voltage Value MT voltage value Min.: 0.00 V, Max.: 20.00 V Pump motor off: 0.00 V
Pump motor on: 12.00 V
-
BH Standby Light Brake hold standby indicator light ON or OFF ON: Indicator light on
OFF: Indicator light off
-
BH Operated Light Brake hold operated indicator light ON or OFF ON: Indicator light on
OFF: Indicator light off
-
TRC/VSC Off Mode TRC/VSC off mode Normal, TRC OFF, VSC Expert Mode or VSC OFF Normal: Normal mode
TRC OFF: TRC off mode
VSC Expert Mode: VSC expert mode
VSC OFF: VSC off mode
-
Number of DTC Number of DTC Min.: 0, Max.: 255 - Number of DTCs output is displayed
FR Speed Sensor Voltage Open Front speed sensor RH voltage open detection Error or Normal Error: Momentary interruption
Normal: Normal
-
FL Speed Sensor Voltage Open Front speed sensor LH voltage open detection Error or Normal Error: Momentary interruption
Normal: Normal
-
RR Speed Sensor Voltage Open Rear speed sensor RH voltage open detection Error or Normal Error: Momentary interruption
Normal: Normal
-
RL Speed Sensor Voltage Open Rear speed sensor LH voltage open detection Error or Normal Error: Momentary interruption
Normal: Normal
-
Yaw Rate Sensor Voltage Open Yaw rate sensor voltage open detection Error or Normal Error: Momentary interruption
Normal: Normal
-
SLA Solenoid Current Linear solenoid addition valve (SLA) current Min.: 0.00 A, Max.: 3.00 A Brake pedal released: 0.00 to 1.50 A -
SLR Solenoid Current Linear solenoid reduction valve (SLR) current Min.: 0.00 A, Max.: 3.00 A Brake pedal released: 0.00 to 1.50 A -
Brake Hold Switch Brake hold switch (Electric parking brake switch assembly) ON or OFF ON: Switch on
OFF: Switch off
-
Reaction Force Pressure Pressure value of stroke simulator Min.: 0.00 MPa, Max.: 24.48 MPa Brake pedal released: 0.00 MPa Brake pedal is being depressed: Changes in proportion to the depression force of the brake pedal
Servo Pressure Pressure value of servo Min.: 0.00 MPa, Max.: 24.48 MPa Brake pedal released: 0.00 to 2.10 MPa Brake pedal is being depressed: Changes in proportion to the depression force of the brake pedal
Accumulator Pressure Accumulator pressure output value Min.: 0.00 MPa, Max.: 24.48 MPa 15.00 to 21.00 MPa
(Pressure stable and pump motor stopped)
When brake fluid is stored in the accumulator: Accumulator pressure changes in accordance with volume of fluid stored in the accumulator
Reaction Force Pressure Sensor Temperature Reaction force pressure sensor temperature Min.: -80°C (-112°F), Max.: 175°C (347°F) -30°C (-22°F) to 100°C (212°F) -
Servo Pressure Sensor Temperature Servo pressure sensor temperature Min.: -80°C (-112°F), Max.: 175°C (347°F) -30°C (-22°F) to 100°C (212°F) -
Accumulator Pressure Sensor Temperature Accumulator pressure sensor temperature Min.: -80°C (-112°F), Max.: 175°C (347°F) -30°C (-22°F) to 100°C (212°F) -
MT Voltage Value (ABS) ABS motor voltage value Min.: 0.00 V, Max.: 20.00 V ABS motor off: 0.00 V
ABS motor on: 11.00 to 14.00 V
-
ECB Solenoid (SGH) Switching solenoid valve (SGH) ON or OFF ON: Solenoid on
OFF: Solenoid off
ECB: Electronically Controlled Brake System
ECB Solenoid (SSA) Switching solenoid valve (SSA) ON or OFF ON: Solenoid on
OFF: Solenoid off
ECB: Electronically Controlled Brake System
Power Supply Voltage Low Light ON Trip Counter Number of trips after light illuminated when power supply voltage was low Min.: 0, Max.: 255 - -
SGH Solenoid Current Switching solenoid valve (SGH) current Min.: 0.00 A, Max.: 3.00 A 0.00 to 1.50 A -
SSA Solenoid Current Switching solenoid valve (SSA) current Min.: 0.00 A, Max.: 3.00 A 0.00 to 1.50 A -
Reaction Force Pressure Sensor Open Reaction force pressure sensor open detection Error or Normal Error: Momentary interruption
Normal: Normal
-
Servo Pressure Sensor Open Servo pressure sensor open detection Error or Normal Error: Momentary interruption
Normal: Normal
-
Ambient Temperature Ambient temperature Min.: -128°C (-198.4°F), Max.: 127°C (260.6°F) -30°C (-22°F) to 100°C (212°F) Changes according to ambient temperature
Air Bag ECU Communication Open Airbag sensor assembly communication open detection Error or Normal Error: Momentary interruption
Normal: Normal
-


ACTIVE TEST


HINT:

Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


a.

Warm up the engine.


b.

Turn the power switch off.


c.

Connect the GTS to the DLC3.


d.

Turn the power switch on (IG).


e.

Turn the GTS on.


f.

Enter the following menus: Chassis / ABS/VSC/TRC / Active Test.


g.

According to the display on the GTS, perform the Active Test.

Chassis > ABS/VSC/TRC > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
ABS Warning Light ABS warning light Warning light ON/OFF Observe combination meter assembly
Brake Warning Light Brake warning light / red (malfunction) Warning light ON/OFF Observe combination meter assembly
ECB Warning Light Brake warning light / yellow (minor malfunction) Warning light ON/OFF
·

Observe combination meter assembly

·

ECB: Electronically Controlled Brake System


Buzzer Meter buzzer Buzzer ON/OFF Buzzer can be heard
Solenoid Relay Solenoid relay Relay ON/OFF -
Motor Relay ABS motor relay Relay ON/OFF Operating sound of motor can be heard.
Stop Light Relay Stop light control relay (Stop light switch assembly) Relay ON/OFF -
ECB Main Relay Main relay Relay ON/OFF ECB: Electronically Controlled Brake System
ABS Solenoid (SRLR) Reduction solenoid valve (RLR) Solenoid ON/OFF -
ABS Solenoid (SRLH) Holding solenoid valve (RLH) Solenoid ON/OFF -
ABS Solenoid (SRRR) Reduction solenoid valve (RRR) Solenoid ON/OFF -
ABS Solenoid (SRRH) Holding solenoid valve (RRH) Solenoid ON/OFF -
ABS Solenoid (SFLR) Reduction solenoid valve (FLR) Solenoid ON/OFF -
ABS Solenoid (SFLH) Holding solenoid valve (FLH) Solenoid ON/OFF -
ABS Solenoid (SFRR) Reduction solenoid valve (FRR) Solenoid ON/OFF -
ABS Solenoid (SFRH) Holding solenoid valve (FRH) Solenoid ON/OFF -
ECB Control Invalid Electronically controlled brake system control invalid Control invalid ON/OFF
·

Electronically controlled brake system control is disabled (braking with no accumulator assist)

·

ECB: Electronically Controlled Brake System


Accumulator Zero Down Reduction of pressure in accumulator Activation ON/OFF Brake fluid in the accumulator makes noise
Actuator Air Bleeding Pattern Actuator air bleeding pattern activation Activation ON/OFF When accumulator pressure drops, pump operation creates sound
BH Standby Light Brake hold standby indicator light Indicator light ON/OFF Observe combination meter assembly
BH Operated Light Brake hold operated indicator light Indicator light ON/OFF Observe combination meter assembly
TRC(TRAC) OFF Indicator Light Multi-information display (Traction Control Turned Off) Display ON/OFF Observe combination meter assembly
VSC OFF Indicator Light VSC OFF indicator light Indicator light ON/OFF Observe combination meter assembly
Slip Indicator Light Slip indicator light Indicator light ON/OFF Observe combination meter assembly
EBS Relay Emergency brake signal operation Operation ON/OFF -
ECB Solenoid (SLR) Linear solenoid reduction valve (SLR) Solenoid ON/OFF ECB: Electronically Controlled Brake System
ECB Solenoid (SLA) Linear solenoid addition valve (SLA) Solenoid ON/OFF ECB: Electronically Controlled Brake System
ECB Solenoid (SSA) Switching solenoid valve (SSA) Solenoid ON/OFF
·

Operation sound of solenoid (clicking sound) can be heard

·

ECB: Electronically Controlled Brake System


ECB Solenoid (SGH) Switching solenoid valve (SGH) Solenoid ON/OFF
·

Operation sound of solenoid (clicking sound) can be heard

·

ECB: Electronically Controlled Brake System


ABS Solenoid Solenoid valve (FRH, FRR, FLH, FLR, RRH, RRR, RLH or RLR) Solenoid SFRH/SFRR/SFLH/ SFLR/SRRH/SRRR/SRLH/SRLR Operation sound of solenoid (clicking sound) can be heard