Home › General › INTRODUCTION › HOW TO USE THIS MANUAL
RM33C0E _V1 General _065429 INTRODUCTION _0328777 HOW TO USE THIS MANUAL F

INTRODUCTION  HOW TO USE THIS MANUAL  GENERAL INFORMATION  


GENERAL DESCRIPTION


a.

Repair operations can be separated mainly into the following 3 processes:

i.

Diagnosis


ii.

Removing/Installing, Replacing, Disassembling/Reassembling, Checking and Adjusting


iii.

Final Inspection



b.

The following procedures are omitted from this manual. However, these procedures must be performed.

i.

Use a jack or lift to perform operations.


ii.

Clean all removed parts.


iii.

Perform a visual check before and after performing any work.




PREPARATION


a.

Use of Special Service Tools (SST) and Special Service Materials (SSM) may be required, depending on the repair procedure. Be sure to use SST and SSM when they are required and follow the work procedure properly. A list of SST and SSM is in the "Preparation" section of this manual.



REPAIR PROCEDURES


a.

A component illustration is placed under the title where necessary.


b.

Non-reusable parts, grease application areas, precoated parts and torque specifications are noted in the component illustrations.

The following illustration is an example.


D100720C18
2.938,1.854 3.521,2.021 0.583,0.167 0.396,2.281 1.052,2.469 0.656,0.188 1.521,0.5 1.76,0.5 false 1.063,0.823 0.844,0.833 false 1.479,1.25 1.729,1.25 false 1.198,2.375 1.063,2.375 false 1.135,2.823 0.958,2.823 false 1.771,2.156 2.01,1.573 2.01,1.573 2.104,1.573 false 2.802,1.938 2.938,1.938 false 4.167,2.198 4.167,2.646 false 3.313,2.646 3.313,2.479 false 5,2.073 5,2.458 false 5.313,2 5.313,2.156 false 5.906,1.75 5.906,2.083 false 6.333,1.677 6.333,1.813 false 6.635,1.552 6.74,1.552 false 4.708,1.896 4.708,1.615 4.708,1.615 4.583,1.615 false 5.615,1.396 5.615,1.198 5.615,1.198 5.531,1.198 false 0.656,1.635 0.906,1.635 false 5.823,1.333 5.823,1.073 5.823,1.073 5.906,1.073 false 5.135,1.094 5.219,1.281 0.083,0.188 10 false ● 2.135,1.479 2.26,1.656 0.125,0.177 10 false ● 2.958,1.875 3.583,2.01 0.625,0.135 8 false 12 (120, 9) 0.427,2.313 1.083,2.448 0.656,0.135 8 false 15 (155, 11) 0.073,0.052 0.896,0.25 0.823,0.198 12 false *A 1.833,0.417 2.146,0.573 0.313,0.156 10 false *1 0.677,0.76 0.99,0.917 0.313,0.156 10 false *2 1.771,1.167 2.083,1.323 0.313,0.156 10 false *3 0.5,1.563 0.813,1.719 0.313,0.156 10 false *4 2.292,1.49 2.604,1.646 0.313,0.156 10 false *5 0.802,2.75 1.115,2.906 0.313,0.156 10 false *6 3.271,2.708 3.583,2.865 0.313,0.156 10 false *7 4.104,2.667 4.417,2.823 0.313,0.156 10 false *8 4.417,1.531 4.729,1.688 0.313,0.156 10 false *9 4.927,2.51 5.396,2.667 0.469,0.156 10 false *10 5.219,2.208 5.458,2.396 0.24,0.188 10 false *11 5.281,1.125 5.75,1.281 0.469,0.156 10 false *12 5.823,2.104 6.292,2.26 0.469,0.156 10 false *13 5.948,1 6.417,1.156 0.469,0.156 10 false *14 6.26,1.844 6.729,2 0.469,0.156 10 false *15 6.792,1.479 7.021,1.646 0.229,0.167 10 false *16
*A Example - -
*1 FILTER CAP *2 FLOAT
*3 RESERVOIR TANK *4 SLOTTED SPRING PIN
*5 GROMMET *6 CYLINDER
*7 PISTON *8 PUSH ROD
*9 WASHER *10 SNAP RING
*11 BOOT *12 GASKET
*13 LOCK NUT *14 CLEVIS PIN
*15 CLEVIS *16 CLIP
V100146

N*m (kgf*cm, ft.*lbf): Specified torque ● Non-reusable part



c.

Torque specifications, grease application areas and non-reusable parts are emphasized in the procedures.

HINT:

There are cases where such information can only be explained by using an illustration. In these cases, torque, oil and other information are described in the illustration.



d.

Only items with key points are described in the text. What to do and other details are explained using illustrations next to the text. Both the text and illustrations are accompanied by standard values and notices.

Illustration What to do and where to do it
Task heading What work will be performed
Explanation text
·

How to perform the task

·

Information such as specifications and warnings, which are written in boldface text




e.

Illustrations of similar vehicle models are sometimes used. In these cases, minor details may be different from the actual vehicle.


f.

Procedures are presented in a step-by-step format.



SERVICE SPECIFICATIONS


a.

Specifications are presented in boldface text throughout the manual. The specifications are also found in the "Specifications" section for reference.



TERM DEFINITIONS


CAUTION Possibility of injury to you or other people.
NOTICE Possibility of damage to components being repaired.
HINT Provides additional information to help you perform repairs.


INTERNATIONAL SYSTEM OF UNITS


a.

The units used in this manual comply with the International System of Units (SI UNIT) standard. Other units from the metric system and the English systems are also provided.

Example:


Torque:
30 N*m (306 kgf*cm, 22 ft.*lbf)