Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM › 2017.09–2021.02
RM33C0E _51 Engine / Hybrid System _065434 CRUISE CONTROL _0328967 DYNAMIC RADAR CRUISE CONTROL SYSTEM C

CRUISE CONTROL  DYNAMIC RADAR CRUISE CONTROL SYSTEM  C1A0A  Front Radar Sensor Region Code Mismatch  


DESCRIPTION

When the destination information in the millimeter wave radar sensor assembly and forward recognition camera do not match, DTC C1A0A is stored.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1A0A Front Radar Sensor Region Code Mismatch When the power switch is on (IG) and the dynamic radar cruise control system is operating, the destination information in the forward recognition camera and millimeter wave radar sensor assembly do not match for approximately 1.3 seconds or more.
·

Millimeter wave radar sensor assembly

·

Forward recognition camera



CAUTION / NOTICE / HINT

NOTICE:
·

Check that the millimeter wave radar sensor assembly has not been replaced with one from another vehicle.

·

When replacing the millimeter wave radar sensor assembly, make sure to replace it with a new one. If a device which was installed to another vehicle is used, the information stored in the millimeter wave radar sensor assembly will not match the information from the vehicle, and as a result, a DTC may be stored.

·

When the millimeter wave radar sensor assembly is replaced with a new one, adjustment of the radar sensor beam axis must be performed.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT

·

When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle. As a result, a DTC may be stored.

·

If the forward recognition camera has been replaced with a new one, be sure to perform Forward Recognition Camera Learning.

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT (SEQUENTIAL RECOGNITION)

·

First check the CAN communication system by following How to Proceed with Troubleshooting. After checking that there are no malfunctions in the CAN communication system, proceed with troubleshooting.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING



PROCEDURE

1.CHECK FOR DTC
a.

Clear the DTCs.

Powertrain > Radar Cruise2 > Clear DTCs
50002 197

b.

Perform the following procedure.

HINT:

If the following procedure is not performed, the previously output DTC cannot be detected.

1.

Turn the power switch on (IG).

2.

Turn the dynamic radar cruise control system on using the cruise control main switch.

3.

Wait for 2 seconds or more.




c.

Check for DTCs.

Powertrain > Radar Cruise2 > Trouble Codes
50001 197

Result:
Result Proceed to
DTC C1A0A is not output A
DTC C1A0A is output B



A

B

2.REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY
2.REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY
a.

Replace the millimeter wave radar sensor assembly.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>REMOVAL


b.

Perform millimeter wave radar sensor assembly adjustment.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT


Result:
Proceed to
NEXT



NEXT

3.CHECK FOR DTC
3.CHECK FOR DTC
a.

Clear the DTCs.

Powertrain > Radar Cruise2 > Clear DTCs
50002 197

b.

Perform the following procedure.

HINT:

If the following procedure is not performed, the previously output DTC cannot be detected.

1.

Turn the power switch on (IG).

2.

Turn the dynamic radar cruise control system on using the cruise control main switch.

3.

Wait for 2 seconds or more.




c.

Check for DTCs.

Powertrain > Radar Cruise2 > Trouble Codes
50001 197

Result:
Result Proceed to
DTC C1A0A is not output A
DTC C1A0A is output B



A

END (MILLIMETER WAVE RADAR SENSOR ASSEMBLY WAS DEFECTIVE)

B

4.REPLACE FORWARD RECOGNITION CAMERA
4.REPLACE FORWARD RECOGNITION CAMERA
a.

Replace the forward recognition camera with a new one.

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>REMOVAL


b.

Perform forward recognition camera adjustment.

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT (SEQUENTIAL RECOGNITION)


Result:
Proceed to
NEXT



NEXT

END (FORWARD RECOGNITION CAMERA WAS DEFECTIVE)