Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM › 2017.09–2018.08
RM33C0E _51 Engine / Hybrid System _065434 CRUISE CONTROL _0328967 DYNAMIC RADAR CRUISE CONTROL SYSTEM U

CRUISE CONTROL  DYNAMIC RADAR CRUISE CONTROL SYSTEM  TERMINALS OF ECU  


CHECK HYBRID VEHICLE CONTROL ECU ASSEMBLY


B344905N26
1.344,0.094 1.729,0.313 0.385,0.219 2.781,0.094 3.167,0.313 0.385,0.219 4.208,0.094 4.594,0.313 0.385,0.219 5.469,0.094 5.854,0.313 0.385,0.219 1.417,0.135 1.875,0.333 0.458,0.198 10 false A28 2.854,0.135 3.313,0.333 0.458,0.198 10 false A29 4.281,0.135 4.594,0.333 0.313,0.198 10 false K69 5.542,0.135 5.854,0.333 0.313,0.198 10 false K70

Terminal No. (Symbols) Wiring Color Terminal Description Condition Specified Condition
A29-26 (DB1) - K69-6 (E1) W - W-B D shift position signal Power switch on (IG), shift lever in D 7.5 to 14 V
Power switch on (IG), shift lever not in D Below 1 V
A29-14 (DB2) - K69-6 (E1) V - W-B D shift position signal Power switch on (IG), shift lever in D 7.5 to 14 V
Power switch on (IG), shift lever not in D Below 1 V
K70-1 (M) - K69-6 (E1) B - W-B S shift position signal Power switch on (IG), shift lever in S 11 to 14 V
Power switch on (IG), shift lever not in S Below 1 V
A28-15 (STP) - K69-6 (E1) LA-G - W-B Stop light switch signal Brake pedal depressed 7.5 to 14 V
Brake pedal released Below 1 V
K69-28 (CCS) - K69-6 (E1) GR - W-B Steering pad switch circuit Cruise control switch not pushed 1 MΩ or higher
Cruise control main switch pushed Below 2.5 Ω
+RES switch pushed 617 to 643 Ω
-SET switch pushed 1509 to 1571 Ω
CANCEL switch pushed 235 to 245 Ω
A29-28 (ST1-) - K69-6 (E1) LG - W-B Stop light switch signal Power switch on (IG), brake pedal depressed Below 1 V
Power switch on (IG), brake pedal released 7.5 to 14 V
K70-8 (SFTD) - K69-6 (E1) G - W-B*1
W - W-B*2
Down-shift position switch signal Power switch on (IG), shift lever in S 11 to 14 V
Power switch on (IG), shift lever in "-" Below 1 V
K70-9 (SFTU) - K69-6 (E1) L - W-B*1
LG - W-B*2
Up-shift position switch signal Power switch on (IG), shift lever in S 11 to 14 V
Power switch on (IG), shift lever in "+" Below 1 V

*1: w/o Shift Paddle Switch

*2: w/ Shift Paddle Switch



CHECK MILLIMETER WAVE RADAR SENSOR ASSEMBLY


A402620N01
3.365,0.063 3.792,0.302 0.427,0.24 3.458,0.115 3.917,0.313 0.458,0.198 10 false A30

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A30-1 (SGND) - Body ground W-B - Body ground Ground Always Below 1 Ω
A30-2 (CA2L) - A30-1 (SGND) W - W-B CAN communication signal Power switch on (IG) Pulse generation
(See waveform 2)
A30-3 (CA2H) - A30-1 (SGND) R - W-B CAN communication signal Power switch on (IG) Pulse generation
(See waveform 1)
A30-5 (CA1P) - A30-1 (SGND) G - W-B CAN communication signal Power switch on (IG) Pulse generation
(See waveform 1)
A30-6 (CA1N) - A30-1 (SGND) W - W-B CAN communication signal Power switch on (IG) Pulse generation
(See waveform 2)
A30-8 (IGB) - A30-1 (SGND) R - W-B Power source Power switch on (IG) 11 to 14 V

a.
A086154E97
2.75,0.271 3.365,0.521 0.615,0.25 10 false 1 V/DIV. 1.365,1.906 2.313,2.094 0.948,0.188 10 false 10 μsec./DIV.

Waveform 1

i.

CAN communication signal

Item Content
Tester Connection
·

Between A30-3 (CA2H) and A30-1 (SGND)

·

Between A30-5 (CA1P) and A30-1 (SGND)


Tool Setting 1 V/DIV., 10 μsec./DIV.
Condition Power switch on (IG)

HINT:

The waveform varies depending on the CAN communication signal.




b.
A086155E89
2.76,0.281 3.396,0.51 0.635,0.229 10 false 1 V/DIV. 1.365,1.875 2.333,2.073 0.969,0.198 10 false 10 μsec./DIV.

Waveform 2

i.

CAN communication signal

Item Content
Tester Connection
·

Between A30-2 (CA2L) and A30-1 (SGND)

·

Between A30-6 (CA1N) and A30-1 (SGND)


Tool Setting 1 V/DIV., 10 μsec./DIV.
Condition Power switch on (IG)

HINT:

The waveform varies depending on the CAN communication signal.





CHECK FORWARD RECOGNITION CAMERA


NOTICE:
·

DTCs may be output when connectors are disconnected during inspection. Therefore, be sure to clear the DTCs using the GTS once the inspection has been completed.

·

Do not apply excessive force to the V6 forward recognition camera connector.



B472992N01
2.073,0.833 2.458,1.042 0.385,0.208 2.188,0.865 2.5,1.063 0.313,0.198 10 false V6

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
V6-7 (IGB) - V6-10 (GND) LA-P - LA Power source Power switch on (IG) 11 to 14 V
Power switch off Below 1 V
V6-5 (CA1P) - V6-10 (GND) L - LA CAN communication signal Power switch on (IG) Pulse generation
(See waveform 1)
V6-11 (CA1N) - V6-10 (GND) W - LA CAN communication signal Power switch on (IG) Pulse generation
(See waveform 2)
V6-6 (CANH) - V6-10 (GND) G - LA CAN communication signal Power switch on (IG) Pulse generation
(See waveform 1)
V6-12 (CANL) - V6-10 (GND) W - LA CAN communication signal Power switch on (IG) Pulse generation
(See waveform 2)
V6-3 (LKSW) - V6-10 (GND) V - LA Vehicle-to-vehicle distance control switch signal Power switch on (IG), vehicle-to-vehicle distance control switch not pushed 4.75 to 5.25 V
Power switch on (IG), vehicle-to-vehicle distance control switch pushed Below 1 V
V6-10 (GND) - Body ground LA - Body ground Ground Always Below 1 Ω

a.
A086154E97
2.75,0.271 3.365,0.521 0.615,0.25 10 false 1 V/DIV. 1.365,1.906 2.313,2.094 0.948,0.188 10 false 10 μsec./DIV.

Waveform 1

i.

CAN communication signal

Item Content
Tester Connection
·

Between V6-5 (CA1P) and V6-10 (GND)

·

Between V6-6 (CANH) and V6-10 (GND)


Tool Setting 1 V/DIV., 10 μsec./DIV.
Condition Power switch on (IG)

HINT:

The waveform varies depending on the CAN communication signal.




b.
A086155E89
2.76,0.281 3.396,0.51 0.635,0.229 10 false 1 V/DIV. 1.365,1.875 2.333,2.073 0.969,0.198 10 false 10 μsec./DIV.

Waveform 2

i.

CAN communication signal

Item Content
Tester Connection
·

Between V6-11 (CA1N) and V6-10 (GND)

·

Between V6-12 (CANL) and V6-10 (GND)


Tool Setting 1 V/DIV., 10 μsec./DIV.
Condition Power switch on (IG)

HINT:

The waveform varies depending on the CAN communication signal.