Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › WATER PUMP WITH MOTOR
RM33C0E _51 Engine / Hybrid System _065433 HYBRID / BATTERY CONTROL _0328991 WATER PUMP WITH MOTOR A

HYBRID / BATTERY CONTROL  WATER PUMP WITH MOTOR  INSTALLATION  


PROCEDURE

Hide G9040 1.INSTALL INVERTER WATER PUMP ASSEMBLY

a.
A406124C02
2.563,0.948 2.646,1.135 2.646,1.135 2.813,1.135 true 2.688,3.906 2.719,3.563 2.719,3.563 2.854,3.563 true 2.563,0.833 2.667,0.448 2.667,0.448 2.833,0.448 true 2.615,3.917 2.563,3.573 2.563,3.573 2.396,3.573 true 0.521,0.156 0.75,0.354 0.229,0.198 10 false *1 0.5,3.354 0.813,3.51 0.313,0.156 10 false *2 2.854,0.365 3.167,0.521 0.313,0.156 10 false *a 2.24,3.479 2.552,3.635 0.313,0.156 10 false *b 2.833,1.042 3.146,1.198 0.313,0.156 10 false *c 1.604,0.5 1.844,0.708 0.24,0.208 10 false *g 2.885,3.469 3.198,3.625 0.313,0.156 10 false *c 2.552,4.385 2.865,4.542 0.313,0.156 10 false *d 1.198,1.073 1.813,1.271 0.615,0.198 10 false 120° 1.313,3.563 1.927,3.76 0.615,0.198 10 false 120° 1.156,3.313 1.406,3.49 0.25,0.177 10 false *e 1.948,0.729 2.26,0.885 0.313,0.156 10 false *d 0.552,3.99 0.792,4.198 0.24,0.208 10 false *f 1.135,0.115 1.375,0.323 0.24,0.208 10 false *f
*1 No. 2 Inverter Cooling Hose
*2 No. 3 Inverter Cooling Hose
*a Alignment Mark (Pink)
*b Alignment Mark (Yellow)
*c Rib
*d 2 to 7 mm (0.0787 to 0.276 in.)
*e Up
*f Front of Vehicle
*g RH Side


Connect the No. 2 inverter cooling hose and No. 3 inverter cooling hose to the inverter water pump assembly and slide the 2 clips to secure them.

NOTICE:

To prevent foreign matter from entering the inverter water pump assembly and inverter cooling system, do not remove the pieces of cloth from the pipes and disconnected hoses until installation.


HINT:
·

Make sure to align the alignment marks of the hoses with the ribs of the inverter water pump assembly.

·

Make sure that the clips are positioned as shown in the illustration.




b.

Temporarily install the inverter water pump assembly to the fan shroud assembly with the 2 bolts.


c.

Fully tighten the 2 bolts.

Torque:
7.0 N*m (71 kgf*cm, 62 in.*lbf)

NOTICE:

As overtightening the bolts may damage the fan shroud assembly, make sure to use a torque wrench.



d.

Connect the inverter water pump assembly connector.

NOTICE:

If a dustproof cap is installed to the inverter water pump assembly connector, do not remove it until the connector is to be connected.



Hide 3.INSPECT FOR COOLANT LEAK (for Inverter)

Hide 53852K 5.INSTALL FRONT WHEEL OPENING EXTENSION PAD LH

Hide 53851M 6.INSTALL FRONT WHEEL OPENING EXTENSION PAD RH