Home › Engine / Hybrid System › CRUISE CONTROL › CRUISE CONTROL SYSTEM
RM33C0E _51 Engine / Hybrid System _065434 CRUISE CONTROL _0329029 CRUISE CONTROL SYSTEM J

CRUISE CONTROL  CRUISE CONTROL SYSTEM  Steering Pad Switch Circuit  


DESCRIPTION

·

The steering pad switch assembly outputs the on/off signal and various control signals to the hybrid vehicle control ECU assembly.

·

The hybrid vehicle control ECU assembly performs cruise control according to the signals received from the steering pad switch assembly.


WIRING DIAGRAM

A408160E06
4.76,3.427 7.156,3.677 2.396,0.25 10 false Hybrid Vehicle Control ECU Assembly 4.438,3.427 4.896,3.625 0.458,0.198 10 false K69 5.844,0.76 6.302,0.958 0.458,0.198 10 false 28 6.094,0.885 6.552,1.083 0.458,0.198 10 false CCS 4.323,0.875 4.781,1.073 0.458,0.198 10 false K22 4.344,2.094 4.802,2.292 0.458,0.198 10 false K22 4.375,0.646 4.833,0.844 0.458,0.198 10 false 13 4.427,1.854 4.885,2.052 0.458,0.198 10 false 2 3.25,2.604 4.948,2.99 1.698,0.385 10 false Spiral Cable Sub-assembly 3.75,1.99 4.208,2.188 0.458,0.198 10 false ECC 3.74,0.771 4.198,0.969 0.458,0.198 10 false CCS 3.229,0.885 3.688,1.083 0.458,0.198 10 false z1 3.229,2.083 3.688,2.281 0.458,0.198 10 false z1 3.229,1.854 3.688,2.052 0.458,0.198 10 false 12 3.271,0.656 3.729,0.854 0.458,0.198 10 false 2 0.823,2.583 2.781,2.917 1.958,0.333 10 false Steering Pad Switch Assembly (Cruise Control Switch) 2.76,1.958 3.219,2.156 0.458,0.198 10 false ECC 2.76,0.781 3.219,0.979 0.458,0.198 10 false CCS 0.458,1.5 0.917,1.698 0.458,0.198 10 false -SET 1.24,1.49 1.698,1.688 0.458,0.198 10 false +RES 1.833,1.49 2.583,1.74 0.75,0.25 10 false CANCEL 2.49,1.49 3.24,1.74 0.75,0.25 10 false MAIN

CAUTION / NOTICE / HINT

NOTICE:
·

The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION

·

Before replacing the hybrid vehicle control ECU assembly, refer to Service Bulletin.



PROCEDURE

1.READ VALUE USING GTS
a.
A401214C01
2.615,1.031 2.865,1.031 true 2.271,0.698 2.396,0.542 2.396,0.542 2.833,0.542 true 2.281,1.396 2.406,1.552 2.406,1.552 2.917,1.552 true 1.75,0.99 2.26,0.99 true 1.552,0.365 1.865,0.521 0.313,0.156 10 false *1 2.885,0.938 3.094,1.146 0.208,0.208 10 true *a 2.927,1.458 3.115,1.656 0.188,0.198 10 true *b 2.865,0.448 3.177,0.604 0.313,0.156 10 false *c 1.594,0.906 1.906,1.063 0.313,0.156 10 false *d
*1 Steering Pad Switch Assembly
*a Cruise Control Main Switch
*b -SET Switch
*c +RES Switch
*d CANCEL Switch


Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Cruise Control / Data List.


e.

Check the Data List to confirm proper functioning of the steering pad switch assembly.

Powertrain > Cruise Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Cancel Switch CANCEL switch status ON or OFF ON: CANCEL switch pushed
OFF: CANCEL switch not pushed
-
-SET Switch -SET switch status ON or OFF ON: -SET switch pushed
OFF: -SET switch not pushed
-
+RES Switch +RES switch status ON or OFF ON: +RES switch pushed
OFF: +RES switch not pushed
-
Cruise Main Switch Operation Condition Cruise control main switch status ON or OFF ON: Cruise control main switch pushed
OFF: Cruise control main switch not pushed
-
Powertrain > Cruise Control > Data List
Tester Display
Cancel Switch
-SET Switch
+RES Switch
Cruise Main Switch Operation Condition
50003 399 21,22,23,1
OK:

The value of each measurement item changes according to the operation of the steering pad switch assembly.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT STEERING PAD SWITCH ASSEMBLY
2.INSPECT STEERING PAD SWITCH ASSEMBLY
a.

Remove the steering pad switch assembly.

Click hereSteering>STEERING COLUMN>STEERING PAD SWITCH>REMOVAL


b.

Inspect the steering pad switch assembly.

Click hereSteering>STEERING COLUMN>STEERING PAD SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

3.INSPECT SPIRAL CABLE SUB-ASSEMBLY

NG

REPLACE STEERING PAD SWITCH ASSEMBLY

3.INSPECT SPIRAL CABLE SUB-ASSEMBLY
a.

Remove the spiral cable sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>REMOVAL


b.

Inspect the spiral cable sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSPECTION


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - HYBRID VEHICLE CONTROL ECU ASSEMBLY AND BODY GROUND)

NG

4.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - HYBRID VEHICLE CONTROL ECU ASSEMBLY AND BODY GROUND)
a.

Disconnect the K22 spiral cable sub-assembly connector.


b.

Disconnect the K69 hybrid vehicle control ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K22-13 (CCS) - K69-28 (CCS) Always Below 1 Ω
K22-2 (ECC) - Body ground Always Below 1 Ω
K22-13 (CCS) or K69-28 (CCS) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR