Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM
RM33C0E _55 Steering _065447 POWER ASSIST SYSTEMS _0329532 POWER STEERING SYSTEM C

POWER ASSIST SYSTEMS  POWER STEERING SYSTEM  C1551  IG Power Supply Voltage  


DESCRIPTION

When a problem occurs in the power source circuit, the fail-safe function works to stop the power assist.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Return-to-normal Condition Note
C1551 IG Power Supply Voltage When the PIG power supply voltage is normal, the IG power supply voltage is 18.5 V or higher
·

Harness or connector

·

Rack and pinion power steering gear assembly


EPS warning light: Comes on The ECU judges the system has returned to normal -

WIRING DIAGRAM

C379337E04
1.438,0.333 2.823,0.698 1.385,0.365 10 false from IG1-NO. 1 Relay 1.448,0.896 2.833,1.26 1.385,0.365 10 false from Auxiliary Battery 3.688,0.51 5.073,0.875 1.385,0.365 10 false EPS-IG1 3.802,1.073 5.188,1.438 1.385,0.365 10 false EPS 5.083,0.219 5.76,0.625 0.677,0.406 10 false 4 5.094,0.771 5.771,1.177 0.677,0.406 10 false 8 5.094,1.271 5.771,1.677 0.677,0.406 10 false 7 5.719,0.365 6.323,0.698 0.604,0.333 10 false IG 5.677,0.865 6.281,1.198 0.604,0.333 10 false PIG 5.667,1.458 6.271,1.792 0.604,0.333 10 false PGND 5.24,2.042 6.573,2.469 1.333,0.427 10 false Power Steering ECU 5.167,2.677 6.667,3.51 1.5,0.833 10 false Rack and Pinion Power Steering Gear Assembly 5.167,2.521 5.563,2.74 0.396,0.219 10 false C71

CAUTION / NOTICE / HINT

NOTICE:
·

If the rack and pinion power steering gear assembly has been replaced, perform assist map writing and torque sensor zero point calibration.

Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>CALIBRATION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (AUXILIARY BATTERY - RACK AND PINION POWER STEERING GEAR ASSEMBLY)
a.

Disconnect the C71 rack and pinion power steering gear assembly connector.

C374510C11
3.375,0.083 3.792,0.333 0.417,0.25 3.448,1.135 2.542,0.719 true 3.469,0.135 3.938,0.396 0.469,0.26 10 false C71 2.354,0.625 2.823,0.885 0.469,0.26 10 false IG 0.125,0.094 0.594,0.354 0.469,0.26 10 false *a
*a Front view of wire harness connector
(to Rack and Pinion Power Steering Gear Assembly)
- -



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C71-4 (IG) - Body ground Power switch on (IG) Below 18.5 V



Result:
Proceed to
OK
NG



OK

2.CHECK FOR DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK FOR DTC
a.

Clear the DTCs.

Chassis > EMPS > Clear DTCs
50002 142

b.

Check for DTCs.

Chassis > EMPS > Trouble Codes
50001 142

Result:
Result Proceed to
DTC is output. A
DTC is not output. B



A

REPLACE RACK AND PINION POWER STEERING GEAR ASSEMBLY

B