Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM
RM33C0E _57 Power Source / Network _065454 NETWORKING _0329710 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Combination Meter ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Combination Meter ECU Communication Stop Mode Any of the following conditions are met:
·

Communication stop for "Combination Meter" is indicated on the "Communication Bus Check" screen of the GTS.

Click here(Click here)

·

Communication stop history for "Combination Meter" is indicated on the "Communication Bus Check (Detail)" screen of the GTS. (The Lost Communication Time value for "Combination Meter" is 6 or more.)

Click here(Click here)

·

Communication system DTCs (DTCs that start with U) that correspond to "Combination Meter ECU Communication Stop Mode" in "DTC Combination Table" are output.

Click here(Click here)


·

Combination meter assembly main line or connector

·

Power source circuit of combination meter assembly

·

Combination meter assembly ground circuit

·

Combination meter assembly



WIRING DIAGRAM

C376341E04
0.167,1.906 0.667,2.177 0.5,0.271 10 false K126 0.573,1.906 2.594,2.177 2.021,0.271 10 false No. 3 CAN Junction Connector 1.552,0.896 2.052,1.167 0.5,0.271 10 false 5 1.521,1.417 2.021,1.688 0.5,0.271 10 false 16 5.375,0.885 5.875,1.156 0.5,0.271 10 false 32 5.375,1.406 5.875,1.677 0.5,0.271 10 false 31 5.635,0.885 6.135,1.156 0.5,0.271 10 false CANH 5.646,1.646 6.146,1.917 0.5,0.271 10 false CANL 1.688,2.354 3.281,2.708 1.594,0.354 10 false from Auxiliary Battery 3.844,2.219 5.01,2.542 1.167,0.323 10 false ECU-DCC NO. 2 5.375,2.25 5.875,2.521 0.5,0.271 10 false 40 5.635,2.354 6.135,2.625 0.5,0.271 10 false B 5.667,3.115 6.167,3.385 0.5,0.271 10 false IG+ 5.385,3.01 5.885,3.281 0.5,0.271 10 false 39 3.99,2.979 4.865,3.302 0.875,0.323 10 false METER-IG2 1.708,3.125 3.469,3.49 1.76,0.365 10 false from IG2-NO. 2 Relay 5.427,3.594 5.927,3.865 0.5,0.271 10 false 2 5.385,4.052 5.885,4.323 0.5,0.271 10 false 21 5.646,3.698 6.146,3.969 0.5,0.271 10 false EP 5.635,4.167 6.135,4.438 0.5,0.271 10 false ES 5.135,4.833 5.635,5.104 0.5,0.271 10 false K21 5.458,4.823 6.656,5.281 1.198,0.458 10 false Combination Meter Assembly

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the power switch on (IG) and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (COMBINATION METER ASSEMBLY MAIN LINE)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the K21 combination meter assembly connector.


c.
C349828C33
1.552,0.615 1.938,0.896 0.385,0.281 1.635,2.625 1.802,2.625 1.802,2.625 1.802,2.125 true 2.104,2.625 1.938,2.625 1.938,2.625 1.938,2.125 true 0.135,0.104 0.448,0.302 0.313,0.198 10 false *a 2.198,2.542 2.781,2.844 0.583,0.302 10 false CANH 1.646,0.667 2.229,0.969 0.583,0.302 10 false K21 1.208,2.552 1.792,2.854 0.583,0.302 10 false CANL
*a Front view of wire harness connector
(to Combination Meter Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K21-32 (CANH) - K21-31 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Result
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (COMBINATION METER ASSEMBLY)

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
C349828C34
1.552,0.615 1.938,0.896 0.385,0.281 2.667,2.604 2.833,2.604 2.833,2.604 2.833,2.104 true 0.677,2.635 0.51,2.635 0.51,2.635 0.51,2.135 true 2.802,2.865 2.969,2.865 2.969,2.865 2.969,2.115 true 0.802,1.083 0.635,1.083 0.635,1.083 0.635,1.833 true 0.135,0.104 0.448,0.302 0.313,0.198 10 false *a 2.375,2.521 2.844,2.729 0.469,0.208 10 false IG+ 1.635,0.667 2.219,0.969 0.583,0.302 10 false K21 0.771,2.531 1.354,2.833 0.583,0.302 10 false ES 2.635,2.792 2.885,3 0.25,0.208 10 false B 0.906,0.99 1.49,1.292 0.583,0.302 10 false EP
*a Front view of wire harness connector
(to Combination Meter Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K21-2 (EP) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω
K21-21 (ES) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω



b.

Reconnect the cable to the negative (-) auxiliary battery terminal.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
K21-39 (IG+) - Body ground Power switch on (IG) 11 to 14 V
K21-40 (B) - Body ground Power switch off 11 to 14 V



Result:
Result
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)