Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM
RM33C0E _57 Power Source / Network _065454 NETWORKING _0329710 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Certification ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Certification ECU Communication Stop Mode Any of the following conditions are met:
·

Communication stop for "Certification (Smart)" is indicated on the "Communication Bus Check" screen of the GTS.

Click here(Click here)

·

Communication stop history for "Certification (Smart)" is indicated on the "Communication Bus Check (Detail)" screen of the GTS. (The Lost Communication Time value for "Certification (Smart)" is 6 or more.)

Click here(Click here)

·

Communication system DTCs (DTCs that start with U) that correspond to "Certification ECU Communication Stop Mode" in "DTC Combination Table" are output.

Click here(Click here)


·

Certification ECU (smart key ECU assembly) branch line or connector

·

Power source circuit of certification ECU (smart key ECU assembly)

·

Certification ECU (smart key ECU assembly) ground circuit

·

Certification ECU (smart key ECU assembly)



WIRING DIAGRAM

C363483E37
0.167,1.844 0.625,2.042 0.458,0.198 10 false K126 5.438,4.052 6.958,4.5 1.521,0.448 10 false Certification ECU (Smart Key ECU Assembly) 5.146,4.052 5.604,4.25 0.458,0.198 10 false K62 5.385,0.75 5.844,0.948 0.458,0.198 10 false 1 5.385,1.344 5.844,1.542 0.458,0.198 10 false 2 5.615,0.865 6.115,1.063 0.5,0.198 10 false CANH 1.677,1.333 2.135,1.531 0.458,0.198 10 false 15 1.698,0.75 2.156,0.948 0.458,0.198 10 false 4 5.615,1.458 6.073,1.656 0.458,0.198 10 false CANL 5.615,2.469 6.073,2.667 0.458,0.198 10 false +B 5.615,3.063 6.073,3.26 0.458,0.198 10 false E 0.552,1.844 2.792,2.135 2.24,0.292 10 false No. 3 CAN Junction Connector 5.323,2.948 5.781,3.146 0.458,0.198 10 false 18 5.396,2.354 5.854,2.552 0.458,0.198 10 false 4 4.021,2.323 5,2.677 0.979,0.354 10 false AM2 1.625,2.458 3.135,2.854 1.51,0.396 10 false from Auxiliary Battery

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the power switch on (IG) and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before replacing the certification ECU (smart key ECU assembly), refer to Service Bulletin.



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) BRANCH LINE)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the K62 certification ECU (smart key ECU assembly) connector.


c.
C348744C24
1.5,0.385 1.865,0.667 0.365,0.281 1.198,1.635 1.198,0.875 1.198,0.875 1.375,0.875 true 1.073,1.635 1.073,0.875 1.073,0.875 0.906,0.875 true 0.156,0.125 0.469,0.323 0.313,0.198 10 false *a 1.573,0.448 2.104,0.813 0.531,0.365 10 false K62 0.49,0.802 1.125,1 0.635,0.198 10 false CANH 1.458,0.792 2.094,0.99 0.635,0.198 10 false CANL
*a Front view of wire harness connector
(to Certification ECU (Smart Key ECU Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K62-1 (CANH) - K62-2 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω



Result:
Result
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
C348744C25
1.5,0.385 1.865,0.667 0.365,0.281 1.083,2.042 1.083,2.635 1.083,2.635 1.26,2.635 true 2.375,1.635 2.375,0.906 2.375,0.906 2.552,0.906 true 0.156,0.125 0.469,0.323 0.313,0.198 10 false *a 1.563,0.448 1.979,0.75 0.417,0.302 10 false K62 1.354,2.573 1.99,2.771 0.635,0.198 10 false E 2.656,0.823 3.292,1.021 0.635,0.198 10 false +B
*a Front view of wire harness connector
(to Certification ECU (Smart Key ECU Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K62-18 (E) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω



b.

Reconnect the cable to the negative (-) auxiliary battery terminal.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
K62-4 (+B) - Body ground Power switch off 11 to 14 V



Result:
Result
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)