Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM
RM33C0E _57 Power Source / Network _065454 NETWORKING _0329710 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Motor Generator Control ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Motor Generator Control ECU Communication Stop Mode Any of the following conditions are met:
·

Communication stop for "Motor Generator" is indicated on the "Communication Bus Check" screen of the GTS.

Click here(Click here)

·

Communication stop history for "Motor Generator" is indicated on the "Communication Bus Check (Detail)" screen of the GTS. (The Lost Communication Time value for "Motor Generator" is 6 or more.)

Click here(Click here)

·

Communication system DTCs (DTCs that start with U) that correspond to "Motor Generator Control ECU Communication Stop Mode" in "DTC Combination Table" are output.

Click here(Click here)


·

Inverter with converter assembly branch line or connector

·

Power source circuit of inverter with converter assembly

·

Inverter with converter assembly ground circuit

·

Inverter with converter assembly



WIRING DIAGRAM

C348700E06
0.667,1.51 2.74,1.885 2.073,0.375 10 false No. 2 CAN Junction Connector 0.354,1.51 0.771,1.76 0.417,0.25 10 false A67 1.708,1.021 2.125,1.271 0.417,0.25 10 false 19 1.74,0.438 2.156,0.688 0.417,0.25 10 false 8 5.365,0.417 5.781,0.667 0.417,0.25 10 false 1 5.375,0.99 5.792,1.24 0.417,0.25 10 false 7 5.677,0.563 6.177,0.833 0.5,0.271 10 false CANH 5.667,2.083 6.083,2.333 0.417,0.25 10 false +B2 5.688,3.313 6.104,3.563 0.417,0.25 10 false IGCT 4.063,1.938 4.75,2.26 0.688,0.323 10 false PCU 3.833,3.156 4.604,3.396 0.771,0.24 10 false IGCT NO. 2 1.615,2.063 2.938,2.365 1.323,0.302 10 false from IGCT Relay 5.677,3.771 6.094,4.021 0.417,0.25 10 false GND1 5.667,4.135 6.083,4.385 0.417,0.25 10 false GND2 5.25,4.76 5.667,5.01 0.417,0.25 10 false A48 5.563,4.76 6.927,5.333 1.365,0.573 10 false Inverter with Converter Assembly 5.677,1.146 6.177,1.417 0.5,0.271 10 false CANL 5.385,1.938 5.802,2.188 0.417,0.25 10 false 5 5.385,2.615 5.833,2.813 0.448,0.198 10 false 6 5.344,3.188 5.792,3.385 0.448,0.198 10 false 12 5.354,3.635 5.802,3.833 0.448,0.198 10 false 24 5.354,4.031 5.802,4.229 0.448,0.198 10 false 23 5.688,2.74 6.104,2.99 0.417,0.25 10 false +B

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the power switch on (IG) and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (INVERTER WITH CONVERTER ASSEMBLY BRANCH LINE)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the A48 inverter with converter assembly connector.


c.
C349824C11
1.479,0.25 1.896,0.51 0.417,0.26 1.333,1.677 1.333,0.625 1.333,0.625 1.167,0.625 true 0.635,1.833 1.292,1.833 true 0.073,0.052 0.385,0.25 0.313,0.198 10 false *a 0.76,0.573 1.198,0.771 0.438,0.198 10 false CANH 0.25,1.781 0.688,1.979 0.438,0.198 10 false CANL 1.563,0.302 2,0.5 0.438,0.198 10 false A48
*a Front view of wire harness connector
(to Inverter with Converter Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A48-1 (CANH) - A48-7 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω



Result:
Result
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY)

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
C349824C12
1.479,0.25 1.896,0.51 0.417,0.26 1.823,1.698 1.823,0.781 1.823,0.781 1.656,0.781 true 1.969,1.833 2.854,1.833 true 1.938,1.688 1.938,0.771 1.938,0.771 2.083,0.771 true 1.958,3 1.823,3 1.823,3 1.823,2.083 true 2.083,2.823 1.948,2.823 1.948,2.823 1.938,2.073 true 0.073,0.052 0.385,0.25 0.313,0.198 10 false *a 1.354,0.729 1.792,0.927 0.438,0.198 10 false +B2 2.927,1.771 3.365,1.969 0.438,0.198 10 false IGCT 1.563,0.323 2,0.521 0.438,0.198 10 false A48 2.167,0.698 2.604,0.896 0.438,0.198 10 false +B 2.167,2.76 2.604,2.958 0.438,0.198 10 false GND1 2.021,2.938 2.458,3.135 0.438,0.198 10 false GND2
*a Front view of wire harness connector
(to Inverter with Converter Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A48-23 (GND2) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω
A48-24 (GND1) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω



b.

Reconnect the cable to the negative (-) auxiliary battery terminal.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A48-5 (+B2) - Body ground Power switch on (IG) 11 to 14 V
A48-6 (+B) - Body ground Power switch on (IG) 11 to 14 V
A48-12 (IGCT) - Body ground Power switch on (IG) 11 to 14 V



Result:
Result
OK
NG



OK

REPLACE MG ECU (REPLACE INVERTER WITH CONVERTER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)