Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › 2017.09–2020.08
RM33C0E _57 Power Source / Network _065454 NETWORKING _0329710 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Grille Shutter Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Grille Shutter Communication Stop Mode Any of the following conditions are met:
·

Communication stop for "Grill Shutter" is indicated on the "Communication Bus Check" screen of the GTS.

Click here(Click here)

·

Communication stop history for "Grill Shutter" is indicated on the "Communication Bus Check (Detail)" screen of the GTS. (The Lost Communication Time value for "Grill Shutter" is 6 or more.)

Click here(Click here)

·

Communication system DTCs (DTCs that start with U) that correspond to "Grille Shutter Communication Stop Mode" in "DTC Combination Table" are output.

Click here(Click here)


·

Swing grille actuator assembly branch line or connector

·

Power source circuit of swing grille actuator assembly

·

Swing grille actuator assembly ground circuit

·

Swing grille actuator assembly



WIRING DIAGRAM

w/ End Shaft Switch
C405259E01
0.26,1.844 0.719,2.042 0.458,0.198 10 false A66 0.583,1.844 2.635,2.146 2.052,0.302 10 false No. 1 CAN Junction Connector 1.688,1.333 2.146,1.531 0.458,0.198 10 false 10 1.729,0.719 2.188,0.917 0.458,0.198 10 false 4 5.375,0.729 5.833,0.927 0.458,0.198 10 false 6 5.375,1.323 5.833,1.521 0.458,0.198 10 false 5 5.625,0.875 6.26,1.177 0.635,0.302 10 false CAN-P 5.604,2.469 6.063,2.667 0.458,0.198 10 false +B 5.625,1.458 6.135,1.656 0.51,0.198 10 false CAN-N 5.385,2.344 5.844,2.542 0.458,0.198 10 false 1 5.604,3.063 6.063,3.26 0.458,0.198 10 false GND 5.375,2.938 5.833,3.135 0.458,0.198 10 false 3 3.781,2.281 4.844,2.542 1.063,0.26 10 false ECU-B NO. 2 1.625,2.469 3.104,2.75 1.479,0.281 10 false from Auxiliary Battery 5.25,4.083 5.708,4.281 0.458,0.198 10 false z26 5.542,4.083 6.885,4.49 1.344,0.406 10 false Swing Grille Actuator Assembly

w/o End Shaft Switch
C350998E59
0.26,1.844 0.719,2.042 0.458,0.198 10 false A66 0.583,1.844 2.635,2.146 2.052,0.302 10 false No. 1 CAN Junction Connector 1.688,1.333 2.146,1.531 0.458,0.198 10 false 10 1.729,0.719 2.188,0.917 0.458,0.198 10 false 4 5.375,0.729 5.833,0.927 0.458,0.198 10 false 6 5.375,1.323 5.833,1.521 0.458,0.198 10 false 5 5.625,0.875 6.26,1.177 0.635,0.302 10 false CANP 5.604,2.469 6.063,2.667 0.458,0.198 10 false +B 5.625,1.458 6.135,1.656 0.51,0.198 10 false CANN 5.385,2.344 5.844,2.542 0.458,0.198 10 false 1 5.604,3.063 6.063,3.26 0.458,0.198 10 false GND 5.375,2.938 5.833,3.135 0.458,0.198 10 false 3 3.781,2.281 4.844,2.542 1.063,0.26 10 false ECU-B NO. 2 1.625,2.469 3.104,2.75 1.479,0.281 10 false from Auxiliary Battery 5.208,4.083 5.667,4.281 0.458,0.198 10 false A46 5.542,4.083 6.885,4.49 1.344,0.406 10 false Swing Grille Actuator Assembly

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the power switch on (IG) and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK VEHICLE TYPE
a.

Check vehicle type.


Result:
Result Proceed to
w/ End Shaft Switch A
w/o End Shaft Switch B



A

2.CHECK FOR OPEN IN CAN BUS LINES (SWING GRILLE ACTUATOR ASSEMBLY BRANCH LINE)

B

4.CHECK FOR OPEN IN CAN BUS LINES (SWING GRILLE ACTUATOR ASSEMBLY BRANCH LINE)
2.CHECK FOR OPEN IN CAN BUS LINES (SWING GRILLE ACTUATOR ASSEMBLY BRANCH LINE)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the z26 swing grille actuator assembly connector.


c.
C378928C31
1.5,0.104 1.865,0.396 0.365,0.292 2.281,1.885 2.115,1.885 2.115,1.885 2.115,1.219 true 1.781,1.885 1.948,1.885 1.948,1.885 1.948,1.219 true 0.125,0.125 0.438,0.323 0.313,0.198 10 false *a 1.583,0.177 1.896,0.375 0.313,0.198 10 false z26 2.365,1.823 2.885,2.031 0.521,0.208 10 false CAN-P 1.292,1.823 1.813,2.031 0.521,0.208 10 false CAN-N
*a Front view of wire harness connector
(to Swing Grille Actuator Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z26-6(CAN-P) - z26-5(CAN-N) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω



Result:
Result
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (SWING GRILLE ACTUATOR ASSEMBLY)

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
C349838C29
1.458,0.156 1.875,0.417 0.417,0.26 1.156,1.802 1.313,1.802 1.313,1.802 1.313,1.229 true 1.771,1.833 1.625,1.833 1.625,1.833 1.625,1.229 true 0.115,0.083 0.427,0.281 0.313,0.198 10 false *a 1.875,1.771 2.313,1.969 0.438,0.198 10 false GND 0.927,1.75 1.365,1.948 0.438,0.198 10 false +B 1.573,0.208 2.01,0.406 0.438,0.198 10 false z26
*a Front view of wire harness connector
(to Swing Grille Actuator Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z26-3 (GND) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω



b.

Reconnect the cable to the negative (-) auxiliary battery terminal.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
z26-1 (+B) - Body ground Power switch off 11 to 14 V



Result:
Result
OK
NG



OK

REPLACE SWING GRILLE ACTUATOR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

4.CHECK FOR OPEN IN CAN BUS LINES (SWING GRILLE ACTUATOR ASSEMBLY BRANCH LINE)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the A46 swing grille actuator assembly connector.


c.
C378928C08
1.5,0.104 1.865,0.396 0.365,0.292 2.281,1.885 2.115,1.885 2.115,1.885 2.115,1.219 true 1.781,1.885 1.948,1.885 1.948,1.885 1.948,1.219 true 0.125,0.125 0.438,0.323 0.313,0.198 10 false *a 1.583,0.177 1.896,0.375 0.313,0.198 10 false A46 2.365,1.823 2.885,2.031 0.521,0.208 10 false CANP 1.292,1.823 1.813,2.031 0.521,0.208 10 false CANN
*a Front view of wire harness connector
(to Swing Grille Actuator Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A46-6(CANP) - A46-5(CANN) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω



Result:
Result
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (SWING GRILLE ACTUATOR ASSEMBLY)

5.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
C349838C17
1.458,0.156 1.875,0.417 0.417,0.26 1.156,1.802 1.313,1.802 1.313,1.802 1.313,1.229 true 1.771,1.833 1.625,1.833 1.625,1.833 1.625,1.229 true 0.115,0.083 0.427,0.281 0.313,0.198 10 false *a 1.875,1.771 2.313,1.969 0.438,0.198 10 false GND 0.927,1.75 1.365,1.948 0.438,0.198 10 false +B 1.563,0.219 2,0.417 0.438,0.198 10 false A46
*a Front view of wire harness connector
(to Swing Grille Actuator Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A46-3 (GND) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω



b.

Reconnect the cable to the negative (-) auxiliary battery terminal.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A46-1 (+B) - Body ground Power switch off 11 to 14 V



Result:
Result
OK
NG



OK

REPLACE SWING GRILLE ACTUATOR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)