Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PARKING ASSIST MONITOR SYSTEM
RM33C0E _56 Audio / Visual / Telematics _065452 PARK ASSIST / MONITORING _0329721 PARKING ASSIST MONITOR SYSTEM C

PARK ASSIST / MONITORING  PARKING ASSIST MONITOR SYSTEM  C1625  Open or Short in Steering Angle Sensor +B  


DESCRIPTION

This DTC is stored if the rear television camera assembly receives a signal via CAN communication from the steering sensor that indicates a power supply problem.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1625 Open or Short in Steering Angle Sensor +B Open or short in steering sensor power source
·

Harness or connector

·

Steering sensor



WIRING DIAGRAM

E224380E96
1.125,3.219 2.875,3.396 1.75,0.177 10 false : CAN Communication Line 3.229,0.604 3.583,0.781 0.354,0.177 10 false BAT 3.229,1.708 3.563,1.885 0.333,0.177 10 false ESS 5.25,2.177 6.719,2.865 1.469,0.688 10 false Rear Television Camera Assembly 2.021,1.344 3.031,1.521 1.01,0.177 10 false ECU-IG1 NO. 2 1.948,0.792 3.063,1.01 1.115,0.219 10 false ECU-DCC NO. 1 0.385,1.188 1.76,1.417 1.375,0.229 10 false from IG1-NO. 1 Relay 0.385,0.625 2.344,0.927 1.958,0.302 10 false from Auxiliary Battery 3.229,2.344 4.635,2.76 1.406,0.417 10 false Steering Sensor 3.031,0.51 3.156,0.688 0.125,0.177 10 false 4 3.031,1.052 3.156,1.229 0.125,0.177 10 false 9 3.031,1.604 3.156,1.781 0.125,0.177 10 false 6 3.229,1.156 3.531,1.333 0.302,0.177 10 false IG 3.219,2.177 3.563,2.354 0.344,0.177 10 false K71

CAUTION / NOTICE / HINT

NOTICE:

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the parking assist monitor system may be needed.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM>CALIBRATION


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (STEERING SENSOR POWER SOURCE)
a.

Disconnect the K71 steering sensor connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
K71-9 (IG) - K71-6 (ESS) Power switch on (IG) 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (STEERING SENSOR POWER SOURCE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (STEERING SENSOR POWER SOURCE)
a.

Disconnect the K71 steering sensor connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K71-6 (ESS) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
K71-4 (BAT) - K71-6 (ESS) Power switch off 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR