Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PARKING ASSIST MONITOR SYSTEM
RM33C0E _56 Audio / Visual / Telematics _065452 PARK ASSIST / MONITORING _0329721 PARKING ASSIST MONITOR SYSTEM Y

PARK ASSIST / MONITORING  PARKING ASSIST MONITOR SYSTEM  HOW TO PROCEED WITH TROUBLESHOOTING  


CAUTION / NOTICE / HINT

HINT:
·

Use the following procedure to troubleshoot the parking assist monitor system.

·

*: Use the GTS.



PROCEDURE

1.VEHICLE BROUGHT TO WORKSHOP
Result:
Proceed to
NEXT



NEXT

2.CUSTOMER PROBLEM ANALYSIS
2.CUSTOMER PROBLEM ANALYSIS
a.

Ask the customer about the problems and the conditions at the time the malfunction occurred to make sure the problem symptom was not temporarily caused by radio waves in the surrounding environment.

HINT:

The parking assist monitor display may be temporarily distorted due to radio waves around the vehicle.

Problem Symptom Cause

*: DTCs output as "Hist" will not be output again after DTCs are cleared.

Both of the following conditions are met:
·

The problem symptom indicates a parking assist monitor display malfunction and the problem symptom cannot be reproduced.

·

DTC C1622 is output as "Hist" only.*


The display may be temporarily distorted when the vehicle is close to an object that transmits radio waves, such as a telecommunication tower, an airport or a truck equipped with a transceiver.



Result:
Proceed to
NEXT



NEXT

3.INSPECT AUXILIARY BATTERY VOLTAGE
3.INSPECT AUXILIARY BATTERY VOLTAGE
a.

Measure the auxiliary battery voltage with the power switch off.

Standard Voltage:

11 to 14 V


If the voltage is below 11 V, replace or recharge the auxiliary battery before proceeding to the next step.


Result:
Proceed to
NEXT



NEXT

4.SYSTEM CHECK
4.SYSTEM CHECK
a.

Check the vehicle specification.


Result:
Result Proceed to
w/ Navigation System A
w/o Navigation System B



A

5.CHECK NAVIGATION SYSTEM

B

6.CHECK AUDIO AND VISUAL SYSTEM
5.CHECK NAVIGATION SYSTEM

Result:
Result Proceed to
Navigation system is normal A
Navigation system is abnormal B



A

7.CHECK COMMUNICATION FUNCTION OF CAN COMMUNICATION SYSTEM*

B

6.CHECK AUDIO AND VISUAL SYSTEM

Result:
Result Proceed to
Audio and visual system is normal A
Audio and visual system is abnormal B



A

7.CHECK COMMUNICATION FUNCTION OF CAN COMMUNICATION SYSTEM*

B

7.CHECK COMMUNICATION FUNCTION OF CAN COMMUNICATION SYSTEM*
a.

Use the GTS to check if the CAN communication system is functioning normally.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM


Result:
Result Proceed to
CAN communication system DTCs are not output A
CAN communication system DTCs are output B



A

8.CHECK FOR DTC*

B

8.CHECK FOR DTC*
a.

Check for DTCs and make a note of any codes that are output.

Chassis > Parking Assist Camera > Trouble Codes
50001 85
Body Electrical > Navigation System > Trouble Codes
50001 212

b.

Clear the DTCs.

Chassis > Parking Assist Camera > Clear DTCs
50002 85
Body Electrical > Navigation System > Clear DTCs
50002 212

c.

Recheck for DTCs. Try to prompt the DTC by simulating the original activity that the DTC suggests.

Chassis > Parking Assist Camera > Trouble Codes
50001 85
Body Electrical > Navigation System > Trouble Codes
50001 212

Result:
Result Proceed to
No DTCs are output A
DTCs are output B



A

9.PROBLEM SYMPTOMS TABLE

B

11.ADJUST, REPAIR OR REPLACE
9.PROBLEM SYMPTOMS TABLE

Result:
Result Proceed to
Fault is not listed in Problem Symptoms Table A
Fault is listed in Problem Symptoms Table B



A

10.OVERALL ANALYSIS AND TROUBLESHOOTING

B

11.ADJUST, REPAIR OR REPLACE
11.ADJUST, REPAIR OR REPLACE
Result:
Proceed to
NEXT



NEXT

12.CONFIRMATION TEST
12.CONFIRMATION TEST
Result:
Proceed to
NEXT



NEXT

END