Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › 2017.09–2021.02
RM33C0E _58 Vehicle Interior _065458 METER / GAUGE / DISPLAY _0330016 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Odo/Trip Switch Malfunction  


DESCRIPTION

In this circuit, the combination meter assembly detects ODO/TRIP switch (trip switch) signals via a direct line.

WIRING DIAGRAM

E369056E01
2.042,2.604 2.75,2.802 0.708,0.198 10 false Trip Switch 1.656,2.615 2.021,2.813 0.365,0.198 10 false K111 1.927,1.115 2.604,1.469 0.677,0.354 10 false ODO/TRIP Switch 4.5,3.167 6.344,3.365 1.844,0.198 10 false Combination Meter Assembly 4.51,2.99 4.875,3.188 0.365,0.198 10 false K20 4.646,2.042 5.01,2.24 0.365,0.198 10 false SW3 4.656,0.844 5.021,1.042 0.365,0.198 10 false ODO 2.677,0.854 2.948,1.031 0.271,0.177 10 false A/B 2.792,2.042 2.948,2.229 0.156,0.188 10 false E 3.01,2.042 3.167,2.229 0.156,0.188 10 false 1 4.448,2.042 4.604,2.229 0.156,0.188 10 false 5 4.438,0.844 4.594,1.031 0.156,0.188 10 false 1 3.021,0.854 3.177,1.042 0.156,0.188 10 false 3 5.719,0.5 5.99,0.719 0.271,0.219 10 false 5 V

CAUTION / NOTICE / HINT

NOTICE:

When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.


PROCEDURE

1.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Combination Meter / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Combination Meter > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
ODO/TRIP Change Switch ODO/TRIP switch (Trip switch) OFF or ON OFF: Switch released
ON: Switch pushed
-
Body Electrical > Combination Meter > Data List
Tester Display
ODO/TRIP Change Switch
50003 409 2
OK:

ODO/TRIP switch (trip switch) condition displayed on the GTS changes with the actual switch operation.



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

2.INSPECT TRIP SWITCH
2.INSPECT TRIP SWITCH


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (TRIP SWITCH - COMBINATION METER ASSEMBLY)

NG

3.CHECK HARNESS AND CONNECTOR (TRIP SWITCH - COMBINATION METER ASSEMBLY)
a.

Disconnect the K20 combination meter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K111-3 (A/B) - K20-1 (ODO) Always Below 1 Ω
K111-1 (E) - K20-5 (SW3) Always Below 1 Ω
K111-3 (A/B) or K20-1 (ODO) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR